Crosley Refrigerator Parts

Installation of the new handle after receiving a very timely shipment from appliance parts pros was simple. I lined up the top of the handle (hooked 90 degrees over the door) and then swung the handle down to meet the corresponding lower screw. The bottom slid and locked into place, then I screwed the top bolt in. Voila! Read more

I replaced the defrost thermostat and the defrost timer. That corrected the problem. Be careful when ordering your parts. I put in my model# and they gave me a defrost timer that was incorrect. I had to return at my cost and order the correct one. Don't assume because you put in your model# that the part is correct. On each part there is a box to put in your model# to check to see if it fits your model. Don't assume that because you put your model# in before that it fits. If not sure, call them... Read more

Ordered parts on Monday, they arrived on Wednesday. Very very pleased. Read more

My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more

I removed the fresh food ice maker found the drain tube for ice maker frozen. This was causing the back of the unit to rust out. This also caused the water to run down the back of the unit the into the duct work and into the freezer causing ice buildup. I then defrosted the freezer removed the rear duct work and the freezer drain pan cover. I found the freezer drain was not draining. I removed the exterior rear cardboard cover and located the freezer drain tube removed it and found that it was... Read more

Changed the Frigidaire Icemaker Fill Tube Part # 241796405 (AP5671747) about a week ago and so far the Frigidaire Refrigerator seems to work fine. Did not use other ordered parts. Recently ice formed around internal evaporator fan and it started making loud noise when then fan and compressor, etc were running. A long winded history noted below if interested: I have been fighting with this Frigidaire Refrigerator for about 3 to 4 years, started out with the evaporator fan making noise when ice... Read more

• Leaking

Changed the Frigidaire Icemaker Fill Tube Part # 241796405 (AP5671747) about a week ago and so far the Frigidaire Refrigerator seems to work fine. Did not use other ordered parts. Recently ice formed around internal evaporator fan and it started making loud noise when then fan and compressor, etc were running. A long winded history noted below if interested: I have been fighting with this Frigidaire Refrigerator for about 3 to 4 years, started out with the evaporator fan making noise when ice... Read more

Removed the worn gasket, cleaned the door, snapped on the new gasket. Read more

Replace dispenser micro switch. Also replaced broken faceplate and rusty screws. Appliance parts Pro YouTube video was helpful in diagnosis and disassembly. Parts arrived quickly. Read more

Remove old handle: (2) large Phillips-head screws where it attaches to top edge of refrigerator door, back out (1)set screw lower end off handle- needs very small hex wrench. Retain screws: none supplied with new handle. Place new handle in place (need to back out the set screw on bottom of handle to slide it fully into place before tightening). Install (2) screws on top end, and snug the lower setscrew. DONE. Read more

Refrigerator door gasket. I ordered one gasket from you guys, it was so easy to replace. Everything is working fine Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more

Replaced the broken dispenser with a new one. Read more

Replaced hose that came with the new washer with this longer one. Read more