Crosley Refrigerator Parts

This shelf trim is the molded edge piece for your refrigerator shelf. It snaps in place to restore a clean, secure lip that helps keep items in place and limits spills from reaching shelves below. What it does:

• Attaches to the edge of a refrigerator shelf to create a finished barrier
• Helps retain items and contain minor spills
• Restores stability when the original trim is cracked or missing
• Common symptoms: broken or loose trim, items sliding off the shelf, trim won't stay attached

• 1 shelf trim

• Disconnect power and remove food from the affected shelf before servicing
• Lift out the shelf or bin and place it on a flat, protected surface
• Release the old trim's tabs and slide or unsnap it from the shelf—avoid forcing or flexing
• Align the new trim and press until fully seated; reinstall the shelf or bin

The Door Switch Assembly is an OEM replacement part for Whirlpool refrigerators. It is responsible for turning the light on when you open the refrigerator door and turning it off when the door is closed. It ensures that the light functions properly, allowing you to easily locate and retrieve items from your refrigerator.

Symptoms of a faulty door light switch include:

• Interior light not turning on when the door is opened
• Interior light staying on even when the door is closed

A bad door light switch can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as the interior light not turning on or off when you open or close the door, it may be time to replace the door light switch.

This Whirlpool replacement part is also compatible with Sears/Kenmore models.
 

Left Hand

The Kickplate Grille is an OEM part for Frigidaire refrigerators. It is positioned at the bottom of the refrigerator, serving both aesthetic and functional purposes by covering the machinery and components located there, while also facilitating proper airflow to these parts to prevent overheating.

Causes of a bad Kickplate Grille can include physical damage such as cracks, warping, or breakage, often resulting from accidental impacts or general wear and tear. 

Symptoms of a bad Kickplate Grille include:

• Noticeable gaps or looseness in the grille's fit against the refrigerator frame
• Increased operational noise due to insufficient cooling of internal components
• Visual unappeal due to damage or discoloration

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Note: Damper Control w/ two switches, if you need a Damper Control with one switch, order part# {AP5688411}

The Shelf Support is an OEM part for Frigidaire refrigerators. This part provides stability and support for refrigerator shelves, ensuring that they remain securely in place and can hold the weight of stored items.

Causes of a bad shelf support can include accidental impacts, overloading the shelves with heavy items, or wear and tear over time. 

Symptoms of a bad shelf support include:

• Shelves that do not stay securely in place
• Sagging or tilting shelves
• Cracks or visible damage on the supports
• Difficulty in adjusting or repositioning shelves

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This temperature control regulates the cooling system to maintain the set temperature. Replacing a failing control restores stable temperatures and dependable operation so your appliance cools as expected. What it does:

• Monitors internal temperature and cycles the cooling system on/off to hold the setpoint
• Lets you adjust the desired temperature via the control
• Helps prevent overcooling and warm spots
• Common symptoms of a bad control: temperature doesn't match setting, unit runs constantly or won't run, no change when adjusting the control, erratic cycling

• 1 temperature control assembly

• Disconnect power before servicing
• Note wire positions; move connectors one at a time to the new control
• If a sensing bulb/capillary is present, route it carefully without kinks or sharp bends
• After installation, set to a mid setting and allow up to 24 hours for temperatures to stabilize

The ice auger and crusher blade crush and shave the ice that dispenses on a refrigerator. This part can be used to repair a refrigerator that is no longer dispensing ice. Sometimes when the ice dispenser malfunctions and makes a loud noise but doesn't dispense cubed or shaved ice, the problem is with the auger and crusher blade. Perform a visual inspection of the auger and crusher blade to ensure no external damage is done to the components.Disconnect the refrigerator from its power source before starting this repair. Open the freezer door to access the ice bucket and dispenser area. The bucket is held in place by fastening clips that can be pushed to remove the bucket. Lay the bucket flat on its back with the auger and blade facing upwards. Remove the old auger and crusher blade by removing the four hex screws. Remove the helix end-cap from the old auger system and replace it with the new one. Repeat these steps in reverse to install the new component.This Whirlpool ice auger and crusher is a genuine OEM product sourced directly from Whirlpool. The part listed is only available individually and is not included with any other parts or original appliances. This part is compatible with Whirlpool, Amana, Kenmore, and Maytag appliances.

This evaporator fan motor circulates cold air across the evaporator coils and through the freezer and fresh-food sections to maintain even temperatures. Replacing a failed or noisy motor restores proper airflow and dependable cooling performance.

• Drives the evaporator fan blade to move air over the coils and throughout the cabinet
• Helps maintain consistent temperatures between freezer and refrigerator compartments
• Failure symptoms include weak/no airflow, the fan not running, loud squealing/rumbling, or the fresh-food section warming up
• Poor airflow can also lead to frost or ice buildup on the freezer back panel

• Disconnect power before servicing; wear cut-resistant gloves and eye protection
• Access the motor behind the freezer's rear panel; use caution around sharp metal and evaporator fins
• Note wire positions; transfer the fan blade and any brackets/grommets from the original motor; secure wiring connections
• Ensure the blade spins freely; engage the door switch when testing and strong airflow after reassembly

The Door Hinge is an OEM part for Whirlpool dryers. This hinge ensures the secure attachment of the dryer door to the appliance, allowing it to open and close smoothly. Right-hand hinge. For the left hinge use AP3047600

Causes of a bad door hinge can include regular wear and tear, accidental impacts, or overloading the door.

Symptoms of a bad door hinge include:

• Door not closing properly
• Door sagging or misaligned
• Difficulty opening or closing the door
• Noises or squeaking when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: White

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

The refrigerator dispenser cover module is an OEM part for Frigidaire refrigerators. This grey module serves as an aesthetic cover that helps protect the dispenser mechanism. It is designed to blend in with the exterior of the refrigerator sheltering its internal components. 

Causes of a bad dispenser cover can include wear and tear over time, exposure to impacts or damage, or cracks that compromise its protective functionality. 

Symptoms of a bad dispenser cover include:

• Exposure of internal dispenser parts  
• Leaks around the dispenser area
• Loose or misaligned fit within the refrigerator
• Cracks or splits in the plastic material

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This water inlet valve controls the flow of household water into the refrigerator system. Replacing a failing valve restores reliable water supply for functions like ice making and dispensing.

• Opens and closes to allow water into the refrigerator as commanded
• Common failure signs: no ice production, slow or no water from dispenser, intermittent fill, or leaks at the valve area
• May cause humming from the valve when energized but not filling

• Unplug refrigerator and shut off the water supply before starting
• Have a towel ready to catch any residual water
• Transfer any mounting hardware or fittings from the old valve if reused
• After installation, restore water and power, then check all connections for leaks

This evaporator defrost heater melts frost from the freezer's evaporator coil during the automatic defrost cycle, restoring proper airflow and cooling. Replacing a failed heater helps prevent recurring ice buildup and temperature swings.

• Heats the evaporator coil at set intervals to clear ice
• Maintains airflow so the fresh food section and freezer cool consistently
• Common signs of failure: heavy frost on the back freezer panel or evaporator
• Other symptoms may include warm refrigerator temperatures, reduced airflow, or fan noise from ice contact

• Disconnect power before servicing; wear appropriate PPE
• Access the heater behind the freezer's rear panel; defrost ice with warm air/steam—avoid sharp tools
• Reinstall in the original position; keep wiring clear of the fan and moving/hot parts; ensure secure harness connections
• After reassembly, verify the defrost cycle per service instructions; if frost returns, also check the defrost thermostat/bi-metal and control

The Grille is an OEM part for Whirlpool refrigerators. This part is typically located at the bottom or top of the refrigerator and serves both functional and aesthetic purposes. It allows for proper airflow to the condenser and other internal components while providing a finished look to the appliance.

Causes of a bad grille can include general wear and tear, accidental impacts, or accumulation of dust and debris over time. 

Symptoms of a bad grille include:

• Visible cracks or breaks in the grille
• Reduced cooling efficiency
• Increased dust or debris buildup
• Loose or misaligned grille
• Unusual noises due to restricted airflow

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.