Crosley Refrigerator Parts

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

The Light Switch is an OEM part for Frigidaire refrigerators. It is designed to control the interior lighting of the refrigerator; the switch activates when the door is opened and deactivates when closed. 

Causes of a bad Light Switch can include mechanical wear from frequent use, which may cause the switch to fail to engage or disengage properly. Electrical issues such as short circuits or loose connections can also prevent the switch from functioning correctly.

Symptoms of a bad Light Switch include:

• The refrigerator light staying on when the door is closed
• The light not turning on when the door is opened
• Flickering or intermittent lighting when the door position changes

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This compressor start device briefly energizes the compressor's start winding to get it running, then disengages automatically. Replacing a weak or open PTC can restore cooling and stop the repeating hum-click from the compressor area.

• Provides the initial boost for the compressor to start, then opens as the PTC warms
• Helps the compressor start reliably on each cooling cycle
• Works with the compressor's overload protector to safeguard the motor circuit
• Common symptoms of failure: not cooling, compressor won't start, rapid clicking or hum-click every few minutes, intermittent cooling after power cycling

• Disconnect power and pull the unit forward to access the compressor compartment
• Remove the start-device cover; note wire positions
• Pull the old start device straight off the compressor terminals; avoid bending the pins
• Align the new device with the C–S–R terminals in the same orientation, push on fully, reconnect wires, reinstall cover, and restore power
• Inspect the mating overload protector and terminal connectors for heat damage before reassembly

The Frigidaire Defrost Heater is an OEM replacement part compatible with select Frigidaire brand refrigerators. This part is designed to maintain optimal freezer temperature and prevent frost buildup. 

Symptoms of a bad part:
• Excessive frost buildup in the freezer
• Freezer not cooling properly
• Loud clicking or buzzing noises

Causes of a bad part:
• Age and wear and tear
• Power surge or electrical issues
• Dirty or clogged condenser coils
• Malfunctioning thermostat

This defrost heater is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerators.
 

The Electronic Control Board is an OEM replacement part for Frigidaire freezers. It functions to operate all freezer systems and components through electronic programming and input received from sensors. 

Causes of a failed control board can include moisture damage impairing circuitry over time, power surges disrupting electronics, or logic and memory failures.

Symptoms of a problematic control include:

• The freezer failing to cool or freeze properly
• Lights or other features not functioning as expected
• Error codes appearing regarding control faults  
• Sensors and components not responding to control signals

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is the complete horizontal ice dispenser bucket assembly with crusher. It fits 22 cubic foot refrigerator models. For 20 cubic foot models order WP2209778. For 25 and 27 cubic foot models order WPW10312300.

This water inlet valve kit restores proper water flow to your refrigerator's ice maker and/or dispenser. Replace a sticking, leaking, or failed valve to resolve no-ice, no-dispense, or slow-fill issues and help prevent water leaks.

• Controls water from the household supply to the ice maker and/or water dispenser on demand
• Opens when energized and closes to seal off flow when inactive
• Common symptoms include no ice production, no or slow water dispensing, dripping at the fill area, leaks near the valve, or unusual buzzing/clicking from the valve
• Helps maintain consistent, reliable filling performance

• Unplug the refrigerator and shut off the water supply before servicing
• Place a towel or container to catch residual water and relieve line pressure
• Note tube and wire locations; transfer bracket/fittings as needed and tighten all connections securely
• Restore water and power, check carefully for leaks, and purge air from the system per manufacturer guidance

Color: Grey

The Icemaker Fill Tube is an OEM replacement part for Whirlpool refrigerators. It delivers water to the icemaker, allowing it to produce ice cubes. It is responsible for directing water from the water inlet valve to the icemaker tray, where it freezes into ice cubes.

A bad fill tube can occur due to wear and tear, blockages, or damage. If you notice symptoms such as no ice production, leaking water, or ice cubes with an unusual shape or size, it may be time to replace the fill tube.

Symptoms of a bad fill tube include:

• No ice production or limited ice output
• Leaking water around the icemaker area
• Irregularly shaped or oversized ice cubes

Repair your refrigerator by replacing the faulty or damaged fill tube with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Refrigerator Drain Connector is an OEM part for Whirlpool refrigerators. It is responsible for directing water and condensation from the evaporator fan coil and defrost into the drain pan. 

Causes of a bad drain connector can include cracks, breaks or deformations caused by repeated thermal cycling or impact damage. Mineral or lime buildup inside the connector over many years can also restrict water flow.

Symptoms of a bad drain connector include:

• Water or condensation leaks around the connector area 
• Puddles or watermarks on the floor behind the fridge
• Slow drainage of water from the evaporator fan coil
• Mold or mildew growth near the connector or drain area

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This refrigerator defrost heater and thermostat assembly restores proper automatic defrosting. The heater melts ice buildup on the evaporator, while the thermostat shuts off power at the right temperature to protect components and keep cooling consistent.

• Heats the evaporator during the defrost cycle to clear frost and ice
• Thermostat opens the circuit as the coil warms, preventing overheating
• Helps restore airflow across the coil and stable fridge/freezer temperatures
• Common symptoms: heavy frost behind the freezer panel, poor cooling or warm temps, fan noise from ice contact, unit not defrosting

• Disconnect power before servicing; remove freezer shelves/bins and the rear panel to access the evaporator
• Carefully defrost built-up ice; note original wire routing and clip locations
• Transfer any brackets/clips and mount the new assembly in the same positions
• Ensure connectors are fully seated and wires are clear of the fan and moving parts before restoring power

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This upper door hinge supports the refrigerator/freezer door at the top pivot, keeping it aligned so the gasket seals and the door opens smoothly. Replacing a worn hinge helps restore proper door swing and reliable closing.

• Supports and pivots the door at the top hinge point
• Maintains door alignment for an even, consistent gasket seal
• Helps prevent door sagging, rubbing, or binding
• Worn hinge symptoms include misalignment, squeaks, poor sealing, or the door popping open

• Disconnect power; remove items from the door.
• Support the door to prevent dropping; remove hinge cover and mounting screws.
• Lift the door off the lower hinge, transfer any spacers/shims, and install the new upper hinge.
• Reinstall and align the door; tighten hardware and verify gasket contact all around.

This meat pan is the refrigerator's deli drawer. Replacing a cracked or missing bin restores smooth sliding access for meats and cheeses and helps keep the fresh food section organized.

• Creates a dedicated compartment for deli items in the fresh food section
• Slides on existing shelf rails for easy access
• Restores proper fit when the original bin is cracked, warped, or missing
• Common symptoms: broken or missing drawer, front lip cracked, drawer falls or won't slide smoothly

• Remove contents; pull the old drawer straight out from the rails
• Inspect and clean the rails; transfer any reusable parts from the old drawer if applicable
• Align the new pan on the rails and slide it fully into place
• If movement is tight, confirm the shelf cover and rails are seated and level

The Drip Tray is an OEM replacement part that fits Frigidaire refrigerators. It is responsible for catching water drips and spills under the water dispenser. Over time, the tray can crack or warp leading to leaks. Causes of failure include loss of the part, accidental damage, and wear over time. 

Symptoms of a failing drip tray include:

• water on the floor
• improper fit allowing leaks
• cracks or breaks in the tray

The drip tray is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, Crosley, and Kenmore refrigerator models

This compressor inverter control board powers and regulates the variable-speed compressor in your refrigerator by converting household AC into the controlled output the compressor needs. Replacing a failed inverter can restore compressor operation and normal cooling performance.

• Receives commands from the main control to vary compressor speed for efficient, steady cooling
• Converts AC line voltage to the controlled output required by the compressor motor
• Common symptoms of failure: refrigerator warm, compressor not running while fans/lights operate
• May also present as intermittent cooling, clicking or humming near the compressor, or visible damage on the module

• Disconnect power before servicing; this is a high-voltage component mounted at the compressor
• Note wire positions and transfer connectors one at a time; ensure all connections are fully seated
• Secure the module to the original mounting to maintain proper heat dissipation and vibration control