Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Indicator light lens covers the pilot lamp opening on your range control panel. Replace when cracked, discolored, or missing to restore visibility.
Purchased the triple burner and dual burner element. I added my model of stove and I was able to pull up diagrams of the stove parts. The parts were easy to find using the diagrams and the burner elements were marked 17 & 15 so I placed my order. Parts were here in a couple of days. The tricky part was figuring out how to get into the stove top. I was a few youtube videos to see different replacement. My husband and I got the stove top off and flipped it over on the counter. We looked at... Read more
Connects washer outer tub to drain pump, channeling water out during drain cycle. Replace if cracked, leaking, deteriorated, or damaged by pests.
Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.
Removed some screws, opened the top of the wash machine, unplugged some wires to remove the part, plugged the wires back into the mew part, put the new water valve into place, secured the water valve with the screw, put the top back on the wash machine, and replaced all remaining screws! Real Simple! Read more
This replacement filter traps debris and contaminants within your appliance's system to help protect internal components and maintain proper performance. Swapping a clogged or damaged filter can restore flow/airflow, reduce odors and buildup, and support efficient operation. What it does:
Color: white. Measures about 1-1/2 inches in diameter.
This is an easy fix, but Appliance Parts Pros make finding the correct part easy. I looked at many sites to get a new knob, as I was tired of using pliers to start the dryer. The images on the grid are worth their weight in gold! Read more
Washer won't advance cycles or stops mid-cycle? This timer sequences fill, wash, drain, and spin stages. Moderate DIY repair restores cycle control.
Watched instructional viedeos on how to replace timer. Read more
One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Washer won't start or spin? A broken lid switch actuator prevents the safety switch from engaging. This plastic striker restores proper operation in 5 minutes.
Replace the broken switch Read more
Washer overfilling or underfilling? The water level pressure switch senses tub pressure to control fill cycles. DIY repair in 20 minutes or less.
Called appliance parts and asked, what was the fix. Told it was fill switch and that I could order it. I was amazed that I received the part the next day without even asking for overnight delivery. I installed the part in less then 20 min. Problem fixed.. Read more
Fix additives not dispensing or standing water in the drawer with this siphon insert. Restores proper bleach and softener flow. Simple 5-minute repair.
Washer drum baffle mounts inside the tub to lift and tumble laundry. Replace if cracked, broken, or missing to prevent snags and restore quiet operation.
Removed old baffle. Had to cut it out with a multi-purpose tool. Replaced with new one. Job was not too bad, and only took about 15-20 minutes. The best part was the fast delivery time for the part. Ordered the PM of one day, and had it in the early morning of the next day. (OUTSTANDING!!!) Read more
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.
I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more
Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.
Installed a new Ignitor & Thermal Fuse. Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.