Crosley Washer Leg Or Foot

The Front Leveling Foot is an OEM part for Whirlpool washing machines. It is designed to support and stabilize the washer by allowing users to adjust the height and level the appliance on uneven floors. Proper leveling ensures smooth operation and minimizes vibrations and noise during wash cycles.

Causes of a bad Front Leveling Foot can include physical damage from excessive force, wear and tear from frequent adjustments, or corrosion due to exposure to water or laundry chemicals. Over time, these factors can compromise the foot’s ability to maintain stability, leading to operational issues.

Symptoms of a bad Front Leveling Foot include:

• The washing machine rocking or wobbling during operation
• Increased vibration and noise
• The washer being unlevel, affecting wash performance
• Difficulty in adjusting the foot

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rear Leveling Leg is an OEM part for Whirlpool washing machines. It provides support and adjustment capability to compensate for uneven surfaces or flooring. By adjusting the height of the rear leveling leg, you can achieve a balanced and stable position for your appliance.

Causes of a faulty or damaged rear leveling leg can include regular use, accidental impact, or wear and tear. A damaged leveling leg can lead to an unstable appliance, increased vibrations, or difficulty in maintaining a level position.

Symptoms of a bad rear leveling leg may include:

• Appliance wobbling or rocking during operation
• Uneven distribution of weight
• Difficulty in aligning the appliance with adjacent units or countertops

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.

Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.

Symptoms that may indicate the need for a replacement leveling leg:

• Uneven or unstable washing machine
• Excessive shaking or vibration during spin cycles
• Difficulty in leveling the washer during installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Rubber grommet for motor mount stud.

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

Leg, adjustable (w/nut)

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.

• Supports and self-levels the rear of the cabinet to maintain stability on uneven floors
• Helps address wobbling/rocking, excessive vibration, rattling or "walking," and an appliance that won't sit level
• Replaces a rear leg that is missing, cracked, or worn
• Promotes smoother operation by helping the unit sit properly level

• Disconnect power; if applicable, turn off the water supply
• With assistance, carefully tilt the appliance to access the rear base
• Remove the damaged rear leg from its mount and install the new leg, ensuring it seats fully
• Lower the unit, verify level with a bubble level, and adjust front legs as needed for final leveling

This leveling foot adjusts the height and balance of your appliance so it sits stable and operates correctly. Replacing a worn or missing foot helps reduce vibration, noise, and unwanted movement during use.

• Supports and stabilizes the appliance by adjusting height at the base
• Helps correct rocking, excessive vibration, or walking during operation
• Can resolve rattling noises caused by uneven footing
• Aids proper door alignment and smooth operation when leveled

• Unplug power and shut off water (if applicable) before servicing
• Tilt or carefully raise the appliance to access the foot
• Thread the new foot in by hand; adjust to level with a bubble level
• Tighten any jam nut or lock mechanism if present; recheck level after placement

This adjustable leveling leg helps stabilize and properly level your appliance on uneven floors. Replacing a worn or missing leg reduces wobble and vibration so doors align and the unit operates smoothly.

• Screws into the base to raise or lower a corner for precise leveling
• Helps prevent rocking, vibration, and rattling during use
• Promotes even weight distribution to protect the cabinet and flooring
• Restores proper door/drawer alignment once the unit is level

• Disconnect power; shut off water supply before servicing
• Carefully pull or tip the appliance to access the leg; use a helper for safety
• Start threads by hand, then adjust height with a wrench—do not over-extend
• Verify level front-to-back and side-to-side; recheck after moving or loading

This leveling foot adjusts the height of your appliance to keep it stable and level on uneven floors. Replacing a worn or missing foot can reduce rocking, vibration, and noise for smoother, safer operation.

• Threads into the base to provide height adjustment
• Helps level the appliance front-to-back and side-to-side
• Restores stability to reduce wobble, vibration, and rattling
• Replace if cracked, stripped, broken, or missing

• Disconnect power; shut off water or gas if applicable
• Carefully raise or tilt and support the appliance to access the foot
• Unthread the old foot; hand-thread the new foot to avoid cross-threading, then adjust with a wrench as needed
• Level the appliance side-to-side and front-to-back; tighten any lock nut if equipped

Single unit. Includes foot pad.

This leveling leg threads into the base of your appliance to level and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking, walking, and vibration, protecting the machine and floor for smoother, quieter operation. What it does:

• Provides adjustable height to level the appliance on uneven floors
• Stabilizes the cabinet to reduce vibration and noise
• Replaces a cracked/missing foot or leg with stripped threads
• Helps address rocking, walking, excessive vibration, rattling, or difficulty leveling

• 1 leveling leg

• Disconnect power; turn off water supply and move/tilt the appliance safely with a helper
• Thread the new leg by hand to avoid cross-threading
• Adjust all legs until the unit is level front-to-back and side-to-side
• If the leg uses a jam nut, tighten it to lock the setting; recheck level after initial use

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor