Crosley Washer Spring Parts

When I removed the cabinet, all of the springs appeared in tact, I had already replaced the counter balance spring so I knew that was not the issue. None of the suspension springs or brackets were broken but they did look worn/rusty so I replaced all of the brackets (2 in front and 1 large in back), all of the suspension spring retainers, and all of the suspension springs and it fixed the issue! I plan to also replace the Self leveling leg spring which is an easy fix since it's on the back of... Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more

Replace the drum drive belt and tension pulley assy. Read more

Replaced Snubber Ring installed spring kit. Watched installation video, found it very helpful to plan repair. The washer runs like new now. Read more

My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

Replaced springs and shocks. Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

Watched the video a few times for door boot seal replacement. It was a lot of help! The spring is the hardest to replace and I did enlist the help of my wife. Everything went back on great. If you have to replace the front panel (with the buttons) be mindful that the buttons are spring loaded and will come out. I did not lose any and it went back together just fine. A little touch up paint on the washer and it all looks brand new and works great. And the parts came in quicker than... Read more

Ordered part, took 2 people to lift washer tub while one hook new hook into place Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more

Store that sold the washer could not get the parts needed for 3 weeks due to delivery from factory. I told them I could get them with a week, I did and I was able to get a repairman in to do the job in 2 hours. Thanks to you. I didn't have the tool to replace the springs, that is why I had to get a serviceman in. I did not want to take the chance that the bracket was broken either. Read more