Dishrack

This dishwasher rack tine row bracket secures the fold-down tine row to the rack so it pivots and locks correctly. Replacing a cracked or missing bracket helps restore stable plate support and smooth loading.

• Secures the fold-down tine row to the dishrack
• Allows the tine row to pivot between upright and flat positions
• Helps keep dishes from tipping during cycles
• Common symptoms: tines won't stay up, row flops loosely, bracket is cracked/missing

• Disconnect power to the dishwasher before servicing
• Pull out the rack and locate the affected fold-down tine row
• Release the old bracket and snap the new bracket onto the rack wires
• Verify the tine row pivots and latches smoothly before returning the rack

This lower dishrack assembly restores smooth loading and organized spacing for plates, bowls, and cookware. Replace a rusted, bent, or missing rack to prevent snags and keep items positioned correctly for reliable wash performance.

• Organizes and supports dishes on the lower level during wash cycles
• Rolls in and out along the tub rails for easy loading and unloading
• Maintains proper spacing and clearance so the lower spray arm can rotate
• Typical symptoms: rusted or flaking coating, broken/bent tines, wobbling rack, binding wheels, items tipping over

• Open the door, fully extend the old lower rack, and lift it off the rails to remove
• Transfer any clip-on holders or dividers from the old rack to the new rack as needed
• Align the new rack's wheels with the rails and slide it into place
• Verify the lower spray arm spins freely with the rack installed

Color: gray. Measures about 3 inches high by 2-1/2 inches deep.

Color: gray. Measures about 3 inches high by 2-1/2 inches deep.

This replacement basket restores organized storage inside your appliance. It securely holds items in place to prevent tipping or falling through, helping you load, access, and clean with confidence.

• Provides a dedicated compartment to keep smaller items contained and upright
• Replaces a cracked, warped, or missing basket
• Helps prevent items from contacting moving parts or obstructing spray/airflow
• Common signs it's time to replace: broken tabs, split seams, or the basket no longer seats correctly

• Disconnect power before servicing
• Open the appliance and remove the old basket; retain any reusable brackets or rack components
• Seat the new basket fully into its designated location
• Do not overload; verify it's stable and clears moving parts before use

This left-hand dishrack support mounts to the rack/rail assembly to hold the rack level and guide it in and out. Replacing a worn support restores smooth rack travel and proper alignment to prevent binding, sagging, or derailment.

• Supports the dishrack on the left side and keeps it level
• Helps the rack slide smoothly without catching or rubbing
• Replaces a cracked, warped, or missing support
• Common symptoms: rack falls off track, binds when sliding, sits unevenly, or makes scraping noises

• Disconnect power and turn off water before servicing
• Pull the rack forward, remove it from the rails, and release the old support's locking tabs/fasteners
• Snap or fasten the new support in the same orientation; reinstall the rack and check for smooth travel

The Tine Row Clip is an OEM replacement part for Whirlpool dishwashers. This part secures the lower basket's tine rows in place to properly support dishes during cleaning. The tight fit of the tine row clip is crucial for optimal functionality of the lower dish rack. This clip is used to hold the tines in place on a dishwasher rack.

Causes of a bad tine row clip can include wear and tear leading to cracks or breaks, or damage from impact if the lower rack is mishandled.

Symptoms of a bad tine row clip include:

• Loose or unstable lower dish rack
• Dishes sliding around or falling through the lower rack during the cycle
• Noise from racks or pieces moving inside the tub
• Difficulty loading or removing dishes from the lower rack

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

This replacement dishrack restores secure loading and proper spacing so wash water reaches every item. Replacing a bent or rusty rack helps prevent tipped dishes and marks from flaking rust, and keeps loading/unloading smooth when the rack rollers are intact.

• Holds plates, bowls, and cups in place during wash and rinse cycles
• Maintains spacing for spray coverage and drying airflow
• Rolls in and out along the rails when paired with functional rack rollers
• Common symptoms include broken or bent tines, flaking coating or rust, items tipping, or difficulty sliding the rack

• Disconnect power to the dishwasher before servicing
• Open the door, pull the rack forward, release rack stops/end caps if present, and slide the old rack off the rails
• Transfer any reusable accessories from the old rack to the new rack as required by your model
• Slide the new rack onto the rails, reinstall rack stops, and verify smooth travel before running a cycle

The Adjuster Assembly (RH) is an OEM part for Whirlpool dishwashers. This right-hand adjuster assembly is responsible for adjusting the height of the dishwasher's upper rack, allowing for flexibility in loading various dish sizes and improving cleaning efficiency.

Causes of a bad adjuster assembly include wear and tear from frequent use, damage due to overloading the rack, or breakage of the plastic components.

Symptoms of a bad Adjuster Assembly include:

• Difficulty in adjusting the upper rack height
• The upper rack not staying in the desired position
• The rack being uneven or unstable
• Issues with loading and unloading dishes

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Keep utensils organized and secure during the wash. This dishwasher silverware basket replaces a cracked or missing basket so flatware stays upright for thorough cleaning, helps prevent small items from slipping through the rack, and streamlines loading. What it does:

• Holds silverware and small utensils in the rack throughout wash and rinse cycles
• Keeps pieces separated and upright to improve cleaning and drying performance
• Helps prevent loose items from contacting the spray arm or falling to the tub bottom
• Replace if the basket is cracked, warped, or missing sections, or if utensils tip over or come out dirty

• 1 silverware basket

• No tools required: slide out the rack, lift out the old basket, and set the new basket in the same location
• Ensure the basket is seated securely and does not interfere with spray-arm rotation
• Load knives and sharp items with points down; avoid nesting spoons for best results

This is one half of the silver basket. For a complete basket you will need to order two(2).

The Tine Row Holder is an OEM part for Whirlpool dishwashers. It is responsible for securing the tines in the dishwasher's rack, keeping them in place to hold dishes, glasses, and utensils securely during the wash cycle.

Over time, the tine row holder can become damaged due to normal wear and tear, repeated loading and unloading of dishes, or accidental mishandling.

Symptoms of a bad tine row holder include:

• Tines that are loose or fall out of place
• Difficulty in loading dishes securely
• Uneven or inadequate cleaning due to improperly spaced items

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Gray. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For white order 675679. To attach these tine tips you will need to order the dishrack gray touch-up paintWP676455.

The Lower Dishrack is an OEM part for Whirlpool dishwashers. It provides space for arranging and securely holding your dishes during the dishwashing cycle.

A bad lower dishwasher dishrack can be caused by regular wear and tear, exposure to hot water and cleaning agents, or accidental damage. If you notice rusting, chipping, or broken tines on the dishrack, it may indicate a problem with the rack itself.

Symptoms of a bad lower dishwasher dishrack include:

• Rust stains or residue on your dishes after a wash cycle
• Difficulty in loading or unloading dishes 
• Unstable or wobbling dishes during the wash cycle
• Limited space or reduced capacity for dishes

Replace your faulty lower dishwasher dishrack with this genuine OEM part to restore your dishwasher. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Dishrack Stop is an OEM part for Whirlpool dishwashers. This part prevents the upper dishrack from being pulled out too far, acting as a safety stop to keep the rack securely in place. One stop per package. Located at the end of the rails that hold the upper rack.

Causes of needing to replace the Dishrack Stop can range from it breaking or becoming dislodged due to excessive force or mishandling, to general wear and tear over time.

Symptoms of a bad or missing Dishrack Stop include:

• The ability to pull the dishrack completely out of the dishwasher tub
• The dishrack becoming dislodged or falling out during operation
• Potential damage to the dishwasher interior or the dishrack itself

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Tine Clip is an OEM replacement part for Whirlpool dishwashers. This clip is designed to secure the tines in the dishwasher rack, keeping them properly aligned to hold dishes and utensils in place during the wash cycle. It ensures stability and maximizes the rack's capacity and efficiency.

Symptoms of a bad Tine Clip include:

• Tines becoming loose or collapsing during the wash cycle
• Difficulty in organizing dishes due to unstable tines
• The clip appearing cracked, broken, or missing

Causes of a failing Tine Clip can include regular wear from repeated use, stress from heavy loads, or accidental damage during loading and unloading. A damaged clip may lead to inefficient cleaning and reduced rack usability.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.