Dishwasher Panel Parts

The Console Assembly is an OEM part for Frigidaire dishwashers. As the control interface, it houses buttons and lights to program wash cycles and monitor status. The assembly covers and protects internal control boards.

Symptoms of a bad console assembly include:

• Non-functioning or unresponsive buttons  
• Water intrusion behind surfaces
• Cracks, chips, or clouding that compromise appearance
• Inability to power on the dishwasher

Causes can be normal wear and tear over time, accidental impact damage, or moisture-related issues. Periodic cleaning helps prevent deterioration. 

This OEM Frigidaire replacement console assembly is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore branded dishwashers. 

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

Inner door panel replaces the interior face of the appliance door, restoring a clean surface and proper support for door components so the door can close and seal as intended. Ideal when the door liner is cracked, dented, or visibly worn. What it does:

• Serves as the interior surface of the door and supports the inner glass or window.
• Provides a mounting surface for latches, seals, and related hardware to help maintain a proper door closure.
• Reduces rattling, visible damage, or interior door gaps that can affect operation.
• Protects internal door components from debris and normal wear.

• Disconnect power and unplug the appliance before starting any repair.
• Use basic hand tools to remove door trim or screws; keep all fasteners for reassembly.
• Handle inner glass and sharp edges carefully—wear gloves and eye protection.
• Refer to the appliance's service manual or OEM instructions for model-specific removal and reinstallation steps.

The Panel Facia is an OEM part for Bosch dishwashers. It is the front control panel of your dishwasher, providing a clean and polished look.

A bad panel facia can occur due to wear and tear over time, accidental damage, or exposure to moisture and cleaning agents. Signs of a faulty facia include cracks, discoloration, or a loose fit that compromises the aesthetic appeal of your dishwasher.

Symptoms of a bad panel facia include:

• Cracks or visible damage on the surface
• Discoloration or fading
• A loose or missing panel

Replace your damaged or worn-out panel facia with this genuine OEM Bosch part to restore the appearance of your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

This control panel mounts on the appliance's door and provides the push-button interface for selecting cycles and options. Replacing a cracked or unresponsive console restores reliable button operation and a clean, factory look. What it does:

• Houses the user-interface buttons and indicator windows used to select cycles/options
• Provides a rigid mounting surface for the door's UI components
• Helps protect internal wiring at the top of the door
• Typical symptoms: buttons don't respond or work intermittently, unit won't start when Start/Resume is pressed, selections change unpredictably, or the console is cracked/loose

• One console assembly

• Disconnect electrical power; turn off the water supply if needed
• Open the door and remove the inner-door perimeter screws to separate the console from the inner panel
• Note and transfer any reusable parts from the old console as required; make secure, straight ribbon/harness connections
• Reassemble the door, restore power, and run a quick function check before final tightening

This control panel is the user-interface assembly on the front of your appliance. It provides the labeled button area to choose cycles and settings and replaces a worn, cracked, or unresponsive console.

• Interfaces with the appliance's main control to register your selections
• Houses the keypad/buttons and cycle/option labels
• Common symptoms include unresponsive or intermittent keys, cracked or warped panel, and worn/peeling labels
• Can help resolve moisture-damaged or sticky/stuck button issues

• Disconnect power at the breaker before servicing
• Support the console while removing screws to avoid straining wiring
• Transfer any brackets, trim, nameplate, or overlay from the original if applicable
• Align tabs and fully seat any ribbon/plug connectors; avoid pinching wires and test operation before final reassembly

The Dishwasher Front Door Panel is an OEM part for Whirlpool brand dishwashers. Forming the outer surface of the door, this stainless panel provides a protective barrier and the surface for mounting handle components. 

Causes of a bad front door panel can include damage from repetitive closure stresses, impacts from loaded dishes, or cracks developing from regular cleaning chemicals.

Symptoms of a bad front door panel include:

• Cosmetic damage detracting from appearance
• Obstructions preventing proper latching of the door  
• Leaks forming at the door gasket sealing surface

This OEM replacement is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models. 

This part is a genuine OEM replacement control panel intended for use with dishwasher models.The control panel allows the user to select the desired cycles of the dishwasher. It houses the buttons and the display. The control panel could become broken or start to malfunction over time, which might include the buttons getting stuck or jammed, or the display failing to light up. When replacing any appliance part, the appliance should be turned off and unplugged from power to prevent potentially serious injuries from occurring. This part was manufactured by Whirlpool. This control panel is sold individually. It is intended for use with dishwasher models manufactured by Whirlpool, Maytag, Jenn-Air, Amana, Admiral, Norge, and other brands.

This console cover graphic is the labeled overlay that mounts on the appliance control console, restoring clear, readable control markings and the console's finished appearance for easier control use and improved cosmetics. What it does:

• Replaces faded, cracked, or peeling control labels so settings and icons are legible
• Restores the visible markings around buttons and knobs for accurate operation
• Covers and protects the underlying console surface from everyday wear
• Improves the appliance's appearance by replacing damaged or discolored graphics

• Disconnect power to the appliance before starting any repair
• Typically installs using the console's existing screws or clips; align carefully before fastening
• Handle the graphic by the edges to avoid fingerprints or damage to the printed surface
• After installation, restore power and verify all controls operate and labels align correctly

The Dishwasher Front Lower Cover is designed to protect and enhance the front appearance of your Samsung dishwasher. This genuine OEM part ensures a seamless fit, maintaining the integrity and aesthetic of your appliance. Crafted from durable materials, the front lower cover provides robust protection against scratches, stains, and everyday wear, extending the life of your dishwasher. Its precise design allows for easy installation, enabling you to restore your dishwasher's functionality without any hassle. The Dishwasher Front Lower Cover not only improves the visual appeal of your kitchen but also helps in maintaining the efficiency of your appliance by safeguarding internal components. Compatible with a wide range of Samsung dishwasher models, this genuine OEM part guarantees compatibility and reliability. If your original front lower cover is cracked, missing, or damaged, the Dishwasher Front Lower Cover is the perfect solution to keep your appliance looking and working like new, providing you with peace of mind and a better kitchen experience.

The Control Module Front Cover is an OEM part for Bosch dishwashers. This front cover protects the internal control board governing all dishwasher functions.

Causes of a bad control module front cover can include cracked or broken plastic from overtightening, damage due to impact or handling, or warping over time.

Symptoms of a bad control module front cover include:

• Lights and controls malfunctioning or not responding
• Water or debris entering the control area
• Loose or missing front cover exposing internal parts
• Damage allowing for short circuits or shock hazards

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Color: White.

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

This replacement dishwasher door forms the hinged front of the tub. Replacing a bent or damaged door restores proper alignment and latching so cycles can run correctly and the wash chamber remains properly contained.

• Creates the front barrier of the wash chamber and supports the latch/handle area
• Aligns with the door gasket to promote a proper seal
• Restores correct closing and latching so the cycle can start
• Common symptoms: difficulty closing, cycle won't start due to door not latching, visible dents/warping, poor seal along the gasket

• Disconnect power and turn off the water supply before servicing
• Support the door and carefully relieve hinge spring tension during removal
• Transfer any reusable components from the old door to the new one as needed
• Run a test cycle to ensure proper latching