Parts for Kenmore 417.99390110 (41799390110, 417 99390110): Drum Parts

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Top panel for laundry center units. Covers and protects the upper surface. Replace if cracked, chipped, discolored, or damaged from wear and tear.

Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.

For a complete drum bearing and shaft kit order 5303281153.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

Dryer not heating or clothes staying damp? This heating element restores proper drying. Moderate DIY repair—requires disassembly and multimeter testing.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Metal heat deflector that mounts near the dryer heating element. Replace if warped, cracked, or damaged to restore proper heat distribution and protect wiring.

Front drum bulkhead for dryers. Mounts inside cabinet to support rotating drum. Replace if cracked, worn, or damaged to restore proper drum rotation.

The Lower Front Felt Seal is an OEM part for Frigidaire dryers. This seal prevents hot air from escaping the dryer drum, ensuring optimal drying efficiency and preventing heat loss. It also helps reduce noise and vibration during operation.

Causes of a faulty lower front felt seal can include wear and tear over time, damage from foreign objects or excessive heat, or adhesive failure. These factors can result in air leakage, increased drying time, or excessive lint buildup.

Symptoms of a front felt seal may include:

• Air leakage around the dryer door or front panel
• Excessive lint accumulation near the dryer opening
• Unusual noises or vibrations during the operation

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Note: For the Hi-Temp Adhesive, order part number 5308027429. Additional parts to check are the rear drum bearing kit 5303281153 and the front felt glide assembly 5303937139.

White front control panel touch pad for washer dryer combos. Replaces cracked, scratched, discolored, or worn touch pad panels on the front control area.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

A single replacement screw fastener used to secure trim, panels, or internal components. Fits specific Frigidaire appliance locations to restore proper fastening and alignment where factory hardware is missing or damaged. What it does:

• Secures plastic trim, brackets, or metal panels in refrigerators and freezers
• Restores proper alignment and prevents rattling or loose parts
• Replaces stripped, corroded, or lost hardware to maintain appliance function
• Works wherever the original factory screw was specified

• One replacement screw

• Use the correct screwdriver or bit to avoid damaging the screw head
• Do not overtighten; snug until seated to prevent cracking plastic or stripping threads
• Replace only with the exact factory part for proper fit and function
• Unplug the appliance or turn off power first if working near electrical components

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

This electrical wire harness routes power and signals between a refrigerator's control components, helping restore proper electrical connections for lights, controls and other powered features. Install the correct harness to replace damaged or frayed wiring. What it does:

• Provides factory-style wiring and connectors to link control boards, switches, lights and compressors
• Restores broken, burned or corroded conductor paths that can cause intermittent or total loss of powered functions
• Ensures correct plug-and-play connections using OEM-style terminals and keyed housings
• Helps eliminate electrical shorts or open circuits caused by damaged harness sections

• One complete wire harness

• Disconnect power (unplug or switch off circuit breaker) before servicing electrical components
• Match connector shapes and keyed positions; do not force connectors or modify terminals
• Route harness along original clips/channels and secure with retained mounts or zip-ties as needed
• Inspect and repair both sides for a reliable connection

Replacement drying rack for washer dryer combo units. Installs inside drum for air-drying delicate items. Order a new rack if yours is cracked or missing.

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

This replacement label restores the appliance's factory rating and identification information so service techs can model, serial, and electrical data at a glance. Durable printed adhesive for interior or exterior mounting. What it does:

• Displays model, serial, and electrical/rating information used for service and parts lookup
• Restores worn or unreadable identification after age or damage
• Preserves safety and compliance markings that belong on the appliance

• Clean and dry mounting surface before applying to ensure good adhesion
• Peel backing and align carefully; press firmly to remove air bubbles
• Avoid installing over vents or moving parts; do not cover safety or operating controls
• If label is near live electrical components, disconnect power before accessing the area

This part has been discontinued by the manufacturer and is no longer available.

This service data sheet supplies the technical information needed for diagnosis and repair, helping identify wiring, component locations, and service specifications quickly. What it does:

• Shows wiring diagrams and circuit layouts to trace electrical issues
• Notes component locations and part references for informed troubleshooting
• Summarizes common diagnostic points and test values used by service techs
• Helps speed accurate diagnosis and reduces time spent searching manuals

• One printed service data sheet

• For technician use only; keep with the appliance service records
• Follow all safety procedures and disconnect power before testing
• Use the information as a supplement to full service manuals and OEM instructions

Vertical spring adjuster insert.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.