Dryer Axle, Roller, Pulley Parts

Shaft that the idler pulley rotates on in your dryer. Replace if worn, wobbling, or causing squealing. Helps maintain proper belt tension and alignment.

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque

This assembly includes the roller shaft and rear support bracket that holds a drum support roller in place inside the dryer. It allows the drum to rotate smoothly on its rear support rollers. Replace this part if the dryer is making squealing, thumping, or rumbling noises, or if the existing shaft is worn, bent, or seized.

Motor drive pulley for dryer drum belt. Installs on motor shaft to transfer power and spin the drum. Replace if worn, cracked, or causing belt slippage.

Replaces a worn, damaged, or misaligned dryer motor pulley. Guides the drive belt and transfers motor power to the drum for proper rotation.

This base shaft is the support shaft that helps the washer's tub or drum stay aligned and rotate smoothly. Replacing a worn shaft restores proper drum support and reduces noise, wobble, and uneven operation. What it does:

• Provides a stable pivot and support for the tub/drum during operation
• Transfers rotational force from the drive components to the drum assembly
• Prevents excessive wobble, vibration, and metal-on-metal contact when intact
• Worn or damaged shafts can cause noise, drum misalignment, or premature bearing wear

• Disconnect power and water supply before servicing; follow all safety precautions
• Replacement typically requires removing the cabinet and drum assembly for access
• Inspect adjacent bearings, seals, and mounting hardware and replace if worn
• Use appropriate tools and follow the OEM service manual

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.

This is a drum roller assembly that supports the dryer drum as it rotates during a cycle. The rollers allow the drum to spin smoothly and quietly on its support shaft. Replace this part if your dryer is making thumping, squealing, or rumbling noises during operation, or if the drum is not turning freely.

Belt tensioner idler arm for dryers. Mounts to the drum support frame to maintain proper belt tension. Replace if cracked, broken, or worn springs.

Supports and helps rotate the dryer drum smoothly. Replace when roller is worn, damaged, or causing friction. Installs on the drum support system.

Motor pulley for dryers. Mounts on the motor shaft to drive the drum belt. Replace if cracked, worn, or causing belt slippage during operation.

Drum roller assembly for dryers. Supports and rotates the drum smoothly. Replace if worn, cracked, or causing squeaking noises during operation.

Right-side idler arm and pin assembly for your dryer's belt tensioning system. Replacement needed when arm is bent, broken, or pin is worn or missing.

Roller shaft for dryer drum support system. Replaces broken, worn, or damaged shafts that cause drum rollers to fail. Essential structural component.

Belt pulley mounts to the dryer motor shaft to drive the drum belt. Replace if pulley is cracked, worn smooth, wobbling, or causing belt slippage.