Dryer Belt

The Belt is an OEM component specifically designed for Whirlpool brand dryers. Located inside the dryer drum, this durable belt rotates the drum and tumbles clothes during cycle operation.  

Symptoms of a bad belt include:

• Clothes taking an excessively long time to dry
• The dryer drum refuses to spin or turn over
• Squealing, grinding, or slipping belt noises 

Causes can range from standard wear and tear over years of use to stretching from overloading. Cracks or splits also weaken belts.

Replacing the belt with a genuine Whirlpool OEM part restores the proper drum rotation needed for efficient drying. This ensures clothes are fluffed and dried thoroughly every cycle. The replacement belt is compatible with dryers from brands including Maytag, KitchenAid, and Jenn-Air.

The drive belt is an OEM part for Frigidaire electric dryers. It acts as a link, transferring power from the dryer motor to turn the tumbling drum. During each drying cycle, the belt works diligently to rotate the drum and toss clothes in heated air.

Causes of belt failure involve normal wear and tear over time. Stretching, cracking, and dry rot are all contributors. Oiling or overloading the dryer can accelerate belt wear. 

Symptoms of a bad belt can include : 

• The dryer failing to start or stop 
• Excessive noise during operation
• Visible cracks or separation in the belt

This OEM replacement belt is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryers. 

This Drive belt keeps the washer's transmission and tub turning by transferring motor power to the drum. Replaces a worn or broken belt to restore normal agitation and spinning performance. What it does:

• Transfers motor torque to the transmission/drum so the washer agitates and spins
• Stops slippage that can cause slow or no spin/agitate cycles
• Helps eliminate squealing or burning-rubber noises when the belt is worn
• Prevents further motor/drive damage from a broken or glazed belt

• Disconnect power and water supply before starting any repairs
• Remove access panels and shift the drum to relieve belt tension for removal
• Inspect pulleys, idler, and motor shaft for wear or debris before installing the new belt
• Route the belt according to the OEM diagram, then test run the machine

Replacement 4PH 2371 drive belt for residential dryers. Restores proper drum rotation and tumble so clothes dry evenly while reducing slipping, squealing, or burning-rubber odors caused by a worn or broken belt. What it does:

• Transfers motor power to rotate the dryer drum for normal tumbling.
• Replace if the drum won't turn, slips under load, squeals, or you notice a burning-rubber smell.
• For appliances that use a 4PH-2371 style drive belt—verify model fit before ordering.
• Helps prevent further wear to the drive system when installed with worn components inspected.

• Always disconnect electrical power (and gas supply if applicable) before starting service.
• Follow the appliance service manual for correct belt routing and proper tensioning.
• Inspect the idler pulley, motor shaft, drum glides, and support rollers; replace any worn parts while accessible.
• After installation, restore power and run a short test cycle to ensure smooth, even drum rotation.

The Belt is an OEM part for GE dryers. This part is responsible for transferring power from the dryer's motor to the drum, enabling it to rotate and tumble your clothes during the drying cycle.

A bad drum drive belt can occur due to wear and tear, stretching, or snapping. If you notice symptoms such as the drum not spinning, unusual noises during operation, or clothes not drying properly, it may be time to replace this belt.

Symptoms of a bad drum drive belt include:

• Drum not spinning
• Unusual noises during operation
• Clothes not drying properly

Restore your GE dryer by replacing the faulty drum drive belt with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Drum Drive Belt is an OEM part for GE electric dryers. It transmits rotational force from the motor to turn the dryer drum during operation.

Causes of a bad belt include cracks, breaks, or excessive stretching from repeated use over time. 

Symptoms include: 

• Drum fails to spin or rotates sluggishly during cycles
• Squealing, slipping, or grinding noises from the drive system  
• Burning rubber smell coming from inside dryer chamber

This GE OEM replacement belt helps optimize dry time and prevent damaged clothes from inefficient spinning. Compatible with some Hotpoint, RCA, and Kenmore models as well, it maintains smooth drum rotation.