Electrolux Pump

The Frigidaire Drain Pump is an OEM part for Frigidaire washing machines. It plays a crucial role in the washer's operation by removing water from the wash tub at the end of each cycle, ensuring your clothes are properly drained before the spin cycle. 

Causes of a bad drain pump can include blockages from debris such as coins, lint, or small items that escape from clothing, as well as motor or impeller damage. Electrical failures can also impair pump function, leading to inadequate water removal.

Symptoms of a bad Frigidaire Drain Pump include:

• Water not draining completely from the washer
• Unusual noises, like humming or buzzing, indicating the pump is struggling
• Washer stopping mid-cycle
• Water pooling around the base of the machine

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drain Pump is an OEM part for Frigidaire washing machines. It's engineered to efficiently remove used water from the washer at the end of each wash cycle, playing a critical role in the appliance's ability to prepare for the next load.  

Causes of a bad drain pump include blockages from small items or debris, mechanical failure due to wear and tear, or electrical issues preventing the pump from operating. 

Symptoms of a bad Drain Pump include:

• Water not draining from the washer
• Unusual noises coming from the pump area, indicating a blockage or failure
• The washer not completing its cycle
• Error codes displayed on the washer related to draining issues

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Drain Pump is an OEM replacement part for Frigidaire front load washers. Located inside the base of the washing machine tub, it actively pumps out water through the drain hose after each cycle completion. Efficient drainage is vital for preventing standing water issues.

Causes of a bad drain pump can include mineral or scale buildup within the pump chamber or impeller over time. The water valve may fail to open fully, blocking drain flow. Bearings may wear, causing the impeller to jam.

Symptoms of a bad drain pump are:

• Incomplete water draining after the cycle
• An accumulation of water remaining in the tub
• Leaking from the base
• Error codes could indicate drainage problems.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore.

This drain pump assembly actively removes water from the washer tub during drain and spin cycles, helping prevent standing water and cycle interruptions. Replacing a worn pump restores proper draining and reliable cycle completion.

• Pumps water from the tub through the drain hose to the household drain
• Common symptoms: no drain or slow draining, water left in tub, cycle stops due to drainage issues
• May present with unusual pump noises (buzzing/grinding) or leaks at the pump housing
• Restores proper water evacuation to allow cycles to finish

• Unplug the appliance and turn off water supply before servicing
• Expect residual water—use towels or a shallow pan when removing hoses
• Access the pump (front lower or rear panel varies by model); disconnect wiring and hoses, and transfer any brackets/grommets from the old pump if needed
• Clear the drain filter, sump, and hose of debris; then test for leaks after installation

This replacement pump moves water/condensate through your appliance so it can drain or recirculate as designed. Replacing a weak or failed pump restores proper water removal and helps prevent leaks, overflows, or nuisance shutoffs.

• Moves collected water from the sump/collection area to a drain hose or internal passage
• Maintains correct water level to prevent overflow conditions
• Common failure signs: water won't pump out, leaks near the base, or loud buzzing/grinding from the pump
• May trigger "bucket full," drain, or pump-related error indicators, depending on the model

• Disconnect power before servicing; allow unit to cool, and expect residual water in the lines or pan
• Note hose routing and wiring connections; transfer any clamps, grommets, or fittings from the old pump if reused
• Ensure hoses are fully seated and not kinked; tighten connections and check for leaks after reassembly
• Test operation after installation and water is expelled properly

The Pump Assembly is an OEM part for Frigidaire washing machines. This assembly includes both the pump and its mounting bracket, working together to remove water from the washer tub. During drain cycles, the pump works vigorously to expel soiled water through the drain hose and out of the machine.

Causes of a bad pump assembly can include residue buildup clogging the pump mechanism over time, worn impeller blades with reduced efficiency, or damage to internal components that restrict water flow.

Symptoms of a failed pump assembly involve issues with drainage, including:

• Water not fully exiting the machine after drain cycles
• Extended drain times with gradual emptying
• Leaks or flooding observed around the rear of the machine

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This water pump moves water through your washer as designed. A properly working pump helps ensure correct water flow and drainage, preventing standing water and cycle interruptions.

• Moves water to support wash and drain operations per your model's design
• Common fix for a washer that won't drain or leaves water in the tub
• Addresses loud humming, grinding, or rattling from the pump area
• Can resolve cycle pauses or errors related to draining/pumping
• Symptoms can include water leaking from the pump housing or hose connections

• Disconnect power and water supply; expect residual water and protect floors with towels or a pan.
• Access location varies by model; remove the appropriate panel, then note and transfer hose and wire connections to the new pump.
• Inspect and clear obstructions in hoses/filters; replace worn clamps or gaskets and ensure secure, leak-free connections.
• Run a short test cycle and recheck for leaks before full use.

The Drain Pump is an OEM part for Frigidaire washing machines, crucial for removing used water from the machine at the end of each wash cycle. This pump ensures that water is efficiently expelled, allowing clothes to move to the spin cycle properly dried.  

Causes of a bad part can stem from blockages by small garments, coins, or debris within the pump or the drain hose, mechanical failure within the pump itself, or electrical issues preventing the pump from operating.  

Symptoms of a bad Drain Pump include:

• The washer not draining water, leaving clothes soaking wet after the cycle.
• A humming sound when the machine reaches the drain cycle, indicating the pump might be powered but blocked.
• Error codes displayed on the washer that signify draining issues.
• Water leakage from the bottom of the washer if the pump or its hoses are damaged.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Pump Assembly is an OEM part for Frigidaire washing machines. This part is responsible for draining the water from the washer at the end of each wash cycle.  

Causes of a bad Washer Pump Assembly can include:

• Obstructions in the pump or its inlet/outlet hoses, which can hinder water flow.
• Wear and tear on the pump's motor or impeller, reducing its effectiveness in water evacuation.
• Electrical issues, such as faulty wiring or connections, that prevent the pump from operating.

Symptoms of a failing Washer Pump Assembly include:

• Water not draining properly from the machine.
• The washer fails to enter the spin cycle due to the presence of excess water.
• Unusual noises during the drain phase, indicating a struggling or damaged pump.
• Error codes displayed on the washing machine that indicate drainage problems.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This drain pump assembly removes water from the tub at the end of wash and rinse cycles, helping your appliance complete cycles and prevent standing water.

• Pumps wastewater out through the drain hose to the household drain
• A failing pump can cause slow or no draining, cycle interruptions, or error codes related to draining
• May also present as water left in the tub or an inability to start the spin/drain portion of a cycle

• Unplug appliance and shut off water supply before service
• Have towels or a pan ready—residual water will drain when hoses are removed
• Note wire and hose orientations before disconnecting; transfer any mounting hardware from the original if reused
• After installation, check for leaks and run a short drain cycle to verify operation

This circulation pump and motor assembly recirculates wash water through the spray arms so dishes get clean. Replace it to restore strong spray and quiet operation when the wash motor fails, becomes noisy, or leaks at the pump.

• Recirculates water from the sump through the spray arms during wash cycles
• Maintains proper water pressure and flow for effective cleaning
• Replaces a seized, weak, or noisy wash (circulation) motor
• Common symptoms: no spray or poor cleaning; humming or grinding from the pump; water leaking beneath the tub near the motor/pump

• Disconnect power and turn off the water supply before servicing
• Remove the toe panel; pull the dishwasher out as needed for under-tub access
• Place a towel to catch residual water; label/photograph wire and hose locations and transfer clamps from the original assembly
• Clean sealing surfaces; seat the assembly fully and test for leaks before reinstallation

Replacement pump assembly that moves water through the appliance to clear standing water and restore normal draining. Installs as a direct swap to address drainage problems and reduce water-related cycle interruptions. What it does:

• Pumps and removes water from the appliance to prevent pooling or overflow.
• Drives normal drain cycles so wash or rinse functions complete properly.
• Can resolve common symptoms such as water remaining in the tub, poor draining, or unusual motor/impeller noise during drain.
• Works with the appliance's existing hoses and wiring to circulate or discharge water as designed.

• Disconnect power and turn off water supply before starting any repair.
• Drain residual water from the appliance and be prepared for some spillage when removing the old pump.
• Label or photograph wiring connections before disconnecting; reconnect wires to matching terminals.
• Inspect hoses and seals while installing; replace any damaged clamps or gaskets to prevent leaks.