Electrolux Dispenser Parts

The Ice Door Bracket is an OEM part for Frigidaire refrigerators. It is a critical component of the ice dispenser mechanism, designed to support and align the ice door properly. This bracket ensures the ice door opens and closes smoothly, maintaining an airtight seal to prevent warm air from entering the freezer compartment and causing frost buildup.

Symptoms of a bad Ice Door Bracket include:

• The ice dispenser door failing to close completely, which can lead to ice melting and freezer burn.
• Excessive frost or ice accumulation near the dispenser area.
• Unusual noise when the dispenser is activated, indicating misalignment or instability.

Causes of a bad ice door bracket can include mechanical stress from repeated use, accidental damage from impact, or wear and tear that weakens the structural integrity of the bracket.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Frigidaire dishwashers. This assembly is responsible for dispensing detergent and rinse aid at the appropriate times during the dishwashing cycle, ensuring that dishes are cleaned and rinsed effectively.

Causes of a bad detergent dispenser assembly can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process. Over time, these issues can compromise the dispenser's functionality.

Symptoms of a bad detergent dispenser assembly include:

• Improper dispensing of detergent or rinse aid
• Residual detergent left in the dispenser after the cycle
• Dishes not being cleaned properly
• The dispenser door not opening or closing correctly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Dispenser Actuator is an OEM part for Frigidaire refrigerators. It is responsible for activating the water dispenser when you press a glass or container against it, allowing water to flow from the dispenser.

You should replace this water dispenser actuator if it stops functioning properly. Causes of a bad actuator can include wear and tear from frequent use, damage from excessive force or impact, or electrical faults within the actuator mechanism.

Symptoms of a bad water dispenser actuator include:

• Water not dispensing when the actuator is pressed
• The actuator sticking or not returning to its original position
• Unusual noises when attempting to dispense water
• Water dispensing intermittently or uncontrollably

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Door Seal is an OEM part for Frigidaire refrigerators. This seal is designed to create an airtight barrier around the ice dispenser door, preventing warm air from entering the freezer and maintaining optimal temperature inside the ice compartment. Please note, this listing is for the seal only, other components are sold separately.

Over time, the ice door seal can become worn out or damaged due to frequent use, exposure to varying temperatures, and regular opening and closing. Causes of a bad ice door seal include cracking, tearing, or loss of elasticity, which can lead to air leaks.

Symptoms of a bad ice door seal include:

• Frost or ice buildup around the ice dispenser
• Warm air entering the freezer compartment
• Increased energy consumption
• Water or condensation around the ice dispenser area
• The ice door not closing properly or sealing tightly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Door Center is an OEM part for Frigidaire refrigerators. This component is part of the ice dispenser system, managing the release of ice through the dispenser chute. It helps prevent cold air from escaping the freezer, maintaining energy efficiency and preserving the ice supply.

You should replace the ice door center if it becomes damaged or fails to seal properly. Causes of a bad ice door center can include regular wear and tear, damage from repeated use, or build-up of ice and debris obstructing its movement.

Symptoms of a bad ice door center include:

• Ice dispenser not working correctly
• Ice build-up around the dispenser area
• Warm air entering the freezer, causing ice to melt or clump
• Increased energy consumption due to poor sealing

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dispenser Drip Tray is an OEM replacement part for Frigidaire refrigerators. It is located below the water and ice dispenser and collects any accidental spills or drips that occur during use. The drip tray helps prevent moisture accumulation on interior surfaces that could lead to mold or mess. It measures about 11 inches wide by 4 inches deep.

Symptoms of a bad dispenser drip tray include:

• Unpleasant odors emanating from unaddressed spills or drips
• Visible water staining or residue buildup below dispenser

Causes of failure are typically just general wear and tear from prolonged use. 

This replacement part is also compatible with models produced by Electrolux, Gibson, Kelvinator, and Kenmore. 

The Dispenser Frame is an OEM part for Frigidaire refrigerators. It provides structural support for the ice and water dispenser assembly, ensuring that all components are securely held in place and function properly. The frame measures about 11x 12 inches

Causes of a bad dispenser frame can include repeated use, physical impact, or exposure to moisture, which can lead to cracks, warping, or breakage. A damaged frame can compromise the functionality of the dispenser, leading to leaks or misalignment of the dispensing components.

Symptoms of a bad Dispenser Frame include:

• The dispenser assembly becoming loose or wobbly
• Leaks around the dispenser area
• Difficulty in dispensing ice or water properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models

The Detergent Drawer is an OEM part for Frigidaire washing machines. It holds and dispenses detergent at the appropriate times during wash cycles. The drawer is designed with compartments to separate powder and liquid detergents for optimized cleaning.

Causes of a bad detergent drawer can include leaks from cracks in the plastic material, malfunctions in the electronic components that control dispensing, or damage to the drawer itself.

Symptoms of a bad Detergent Drawer include:

• Incorrect or insufficient detergent amounts dispensed during cycles
• Residue, puddles, or leaks of detergent inside the washer tub or housing
• Odors or mold growth near the detergent area
• The drawer failing to open or close fully

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Dispenser Assembly is an OEM part for Frigidaire dishwashers. It is responsible for dispensing detergent and rinse aid during the dishwashing cycle, ensuring that the correct amounts are released at the appropriate times for optimal cleaning and drying performance.

Causes of a bad dispenser assembly can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process. These issues can prevent the detergent or rinse aid from being properly released.

Symptoms of a bad dispenser assembly include:

• Improper dispensing of detergent or rinse aid
• Insufficient cleaning or rinsing results
• Leaks or drips from the dispenser area
• The dispenser door not opening or closing correctly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dispenser Drawer Assembly is an OEM part for Frigidaire washing machines. It houses the mechanisms that dispense detergent and fabric softener into the wash drum at the appropriate times in each cycle. The dispenser drawer plays an important role in the automatic dosing of cleaning agents for optimized wash performance.  

Symptoms of a bad dispenser drawer include:

• Failure to dispense detergent or fabric softener 
• Dispenser drawer stuck open or closed
• Chemical leaks or exposure in the dispenser area  
• Electrical problems like buzzing or lights that won't illuminate
• Abnormal or incomplete cycle operation

Causes may include damage preventing proper opening/closing, worn dispenser components that malfunction, or electrical issues within the dispenser.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore washing machine models.
 

The Dispenser Module is an OEM part for Frigidaire refrigerators. This part controls and operates the water and ice dispenser functions.

Causes of a bad Dispenser Module can include electrical malfunctions, physical damage from impact or moisture, or general wear and tear over time.

Symptoms of a bad Dispenser Module include:

• Failure of the water or ice dispenser to operate
• Inconsistent or partial dispensing of water or ice
• Leaks or drips from the dispenser area
• Error codes or indicator lights related to the dispenser

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This refrigerator dispenser actuator is the paddle/lever you press with your glass to start ice or water dispensing. Replacing a cracked or worn actuator restores smooth operation and consistent switch engagement at the door dispenser.

• Engages the dispenser micro switch to initiate ice or water dispensing
• Provides the user-facing paddle/lever in the dispenser recess
• Helps the dispenser return to its rest position after you release
• Common symptoms: no dispense when pressed, intermittent response, broken/loose paddle, sticking or continuous dispense if jammed

• Unplug the refrigerator and shut off the water supply before servicing
• Carefully remove the dispenser trim/escutcheon to access the actuator; protect the finish and avoid breaking locking tabs
• Note spring and pivot orientation; transfer any reusable hardware to the new actuator
• Reassemble, restore power/water, and test both ice and water dispensing

The Cover is an OEM part for Frigidaire washing machines. This cover marks the location and type of detergent, bleach, or fabric softener to be used, ensuring proper distribution during the wash cycle. It provides clear guidance for correct detergent placement, contributing to optimal washing performance.

Causes of a bad cover can include wear and tear over time, damage from harsh cleaning agents, or physical impact resulting in cracks or faded markings.

Symptoms of a bad dispenser drawer compartment cover include:

• Faded or illegible markings
• Detergent not dispensing correctly
• Leaks or spills around the dispenser area
• Visible cracks or damage to the cover

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This dispenser assembly replaces a worn or damaged refrigerator dispenser to restore reliable dispensing of water and ice. It provides the dispenser housing and interface needed for proper user operation and sealing at the door. What it does:

• Houses the dispenser components and provides the push-lever/door opening for water and ice delivery
• Restores a broken, cracked or loose dispenser opening that causes poor engagement or cosmetic damage
• Helps stop minor leaks or drips at the dispenser area when seals and gaskets are intact
• Eliminates sticking or misaligned dispenser operation that prevents normal dispensing

• Disconnect power and shut off the water supply before beginning any work.
• Installation typically requires removing the refrigerator door panel(s) and detaching the old dispenser from the inner door; keep fasteners for reuse unless replacements are provided.
• Handle plastic parts gently to avoid cracking; inspect door seals and gaskets and replace if worn.
• After installation, restore power and water, then test dispenser operation and check for leaks.

A replacement dispenser assembly for refrigerator doors that secures dispenser components and restores normal dispenser function and appearance. Installs in the door to replace cracked, loose, or damaged dispenser housings and trim. What it does:

• Provides the mounting and trim for the door dispenser spout and controls.
• Restores proper alignment and fit when the original dispenser housing is cracked, broken, or loose.
• Helps stop rubbing or interference that can cause the dispenser lever or ice/water chute to stick.
• Addresses visible damage and improves the door's finished appearance.

• Disconnect power and shut off the water supply before starting work.
• Installation typically requires removal of the inner door panel and removal/installation of screws and clips; save all hardware.
• Handle door trim and any water lines carefully to avoid damage; check for leaks after reconnecting the water.

This handle assembly replaces a damaged or worn refrigerator door handle, restoring a secure grip and normal door operation. It provides an OEM-fit replacement that mounts in the factory handle location for a neat, finished look. What it does:

• Replaces a broken, cracked, or loose refrigerator door handle
• Restores a solid grip for opening and closing the door
• Helps prevent further damage to the door trim or handle mounting area
• Keeps the cabinet appearance consistent with the original finish

• Disconnect power and remove food from the door area before starting work
• Use appropriate hand tools to remove mounting screws or caps; retain fasteners for reassembly
• Align assembly with mounting posts and secure without over-tightening to avoid cracking
• If door trim or mounting hardware is damaged, inspect and replace as needed for a secure fit