Electrolux Spring Parts

The Suspension Spring Kit is an OEM replacement part for Frigidaire front-loading washing machines. These suspension springs are positioned at the top front of the washer, underneath the tub, to help support the weight of the drum during operation.

Over many cleaning cycles, suspension springs can wear down and lose their ability to dampen vibration.

Symptoms of bad suspension springs include:

• Excessive shaking or rattling of the washing machine
• Loud banging or knocking noises coming from inside the washer
• The tub moving excessively during washing and spinning

It is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Inner Bellow Spring Clamp is an OEM replacement part for Frigidaire front-loading washing machines. It anchors the interior bellow seal in the proper sealing position.

Causes of replacement include torsion fatigue from years of door opening/closing stresses. Mineral buildup may also restrict needed tension if left unchecked.

Symptoms consist of:

• Visible water leakage from the base of the washer door during active cycles
• Looseness permitting shifting or twisting of bellow position
• Inability to achieve proper water-tight integrity checks

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

This replacement spring restores the correct tension in the affected mechanism on your appliance, helping parts return smoothly and stay aligned. A fatigued or broken spring can cause loose action, noise, or improper engagement—this fixes it fast. What it does

• Provides return tension to the related mechanism so parts move and reset correctly
• Helps maintain alignment and reduces looseness or rattle during operation
• Supports smooth engagement/disengagement of linked components
• Common symptoms: weak/loose action, parts not returning to position, squeaking/rattling, visible break or deformation

• 1 spring

• Disconnect power; for gas appliances, shut off gas. For washers, also turn off water supply.
• Support the component under spring tension before removal to prevent sudden release.
• Note or photograph original routing and anchor points to match orientation on reassembly.
• Inspect related brackets/clips; replace any that are bent, worn, or corroded.

This rear shock absorber kit stabilizes the washer tub by damping movement and vibration. Replacing a worn shock restores smoother, quieter spins and helps prevent the drum from banging the cabinet or the machine from walking. What it does:

• Dampens tub movement to control vibration during wash and spin
• Helps prevent banging/thumping noises and cabinet contact
• Reduces "walking" or excessive shaking of the washer
• Can help minimize out-of-balance interruptions

• One rear shock absorber kit

• Disconnect power and turn off water before servicing
• Support the tub/drum to relieve load before removing the shock
• Remove retaining pins/bolts; install the new shock in the same orientation and transfer any reusable hardware
• For consistent damping, replacing shocks in pairs or as a complete set is commonly recommended

This front shock absorber kit stabilizes the washer's tub during spin to reduce vibration and noise. Replacing worn dampers helps restore smooth operation and protects the cabinet and suspension from excessive movement.

• Dampens and controls tub movement during wash and spin
• Helps reduce shaking, "walking," and loud thumping/banging noises
• Can help when the washer won't reach or maintain full spin due to imbalance
• Replaces weakened or damaged front shock mounts/dampers

• Disconnect power and water before servicing
• Access shocks per your model's procedure; support the tub to relieve load
• Install with mounts aligned and fasteners tightened securely; verify free tub movement
• Many replace shocks in pairs to maintain balanced damping

This torsion spring mounts in the dispenser to return the ice chute door/flapper to the closed position after dispensing. Replacing a weak or broken spring helps stop warm air leaks, frost, and ice clumping in the chute.

• Provides the closing force for the dispenser ice door
• Helps seal the ice chute to reduce frost and moisture intrusion
• Typical symptoms: ice door won't close fully, frost/ice buildup around the chute, cubes dropping after dispensing, or air leakage at the dispenser
• Replace if the spring is broken, deformed, or has lost tension

• Disconnect power before servicing; shut off water if working near the dispenser area
• Remove dispenser trim/bezel and control panel to access the ice door assembly; support wiring harnesses
• Note spring orientation and preload before removal; install the new spring on the same hinge posts in the same direction
• Manually cycle the flapper to ensure smooth return and a full seal before reassembly

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

The Spring is an OEM part for Frigidaire washing machines. It is a component that assists the movement of the inner basket or tub during the wash cycle. The spring plays a crucial role in dampening vibrations and absorbing shocks to provide stability, preventing excessive noise and movement.

Causes of a spring failure can include wear and tear over time, exposure to heavy loads or unbalanced loads that put excessive strain on the spring, or damage due to impact or mishandling.

Symptoms of a bad Spring include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises
• The washer moving or walking during operation
• Leaks due to increased stress on the tub and other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door latch spring restores the return tension in your microwave's door release mechanism so the latch engages and releases correctly. Replacing a fatigued or broken spring helps ensure safe door operation and reliable interlock switch activation.

• Provides the return force for the latch lever/door release button
• Helps door hooks engage fully and release smoothly
• Supports proper interlock switch actuation so the unit will run only when the door is closed
• Typical failure signs: door won't latch, "open/close door" error, door button sticks, or needing to hold the door shut to start

• Disconnect power. Microwaves can retain dangerous high voltage even when unplugged; discharge the capacitor
• Access the latch assembly behind the control panel; note the spring's orientation and attachment points
• Use needle-nose pliers to install without overstretching; inspect the latch lever and door hooks for wear
• Verify proper door closure and interlock switch operation before reassembly

This genuine replacement spring restores proper tension and smooth movement in the affected mechanism, helping your appliance operate reliably. Replacing a weakened or broken spring can reduce noise and correct misalignment caused by lost tension.

• Maintains tension and provides return force for connected levers, brackets, or linkages
• Helps keep components in position and minimizes excess play or rattling
• A weakened, stretched, or broken spring can cause poor engagement or inconsistent operation
• Common signs include parts not returning to rest, excess slack, or new noises from the area

• Disconnect power; also shut off water supply
• Note the spring's hook orientation and routing; take a reference photo before removal
• Control the spring with pliers and wear gloves/eye protection to avoid snap-back injuries
• Inspect related brackets/retainers and replace any worn components to ensure proper tension

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

This small but critical actuator spring restores return tension in a refrigerator's actuator mechanism, helping the lever reset to neutral after use so controls feel responsive and operation stops cleanly. What it does:

• Provides the return force for an actuator or lever so it moves back to its neutral position
• Helps the mechanism engage/disengage a switch cleanly
• Common symptoms of a weak or broken spring: lever sticks, feels loose, or doesn't spring back
• Contribute to intermittent activation or failure to stop when released

• 1 actuator spring

• Disconnect power; if working near the dispenser/water system, shut off the water supply
• Access the actuator mechanism and note the spring's exact orientation (take a photo before removal)
• Use needle-nose pliers to transfer the spring; do not over-stretch or deform it
• Wear cut-resistant gloves and eye protection; test lever return action before reassembly

This spring restores tension to the door lock mechanism so the latch returns to its proper position after operation. A worn or missing spring can cause a loose latch, difficulty locking, or a door that won't stay secured during a cycle.

• Returns the door lock latch to its resting position
• Helps ensure the door locks securely during operation
• Symptoms can include a floppy/loose latch, intermittent lock errors, or door not staying latched
• Also helps resolve issues where the door won't unlock smoothly

• Disconnect power before servicing
• Access the door lock assembly per your model's service procedure
• Note spring orientation during removal; install the new spring in the same positions
• Latch operation by gently opening/closing the door before reassembling

This control rod spring fits the refrigerator's ice maker shutoff arm. It restores proper tension so the ice maker cycles on/off correctly and stops making ice when the bucket is full.

• Maintains tension on the ice maker control/shutoff arm for reliable on/off operation
• Helps the arm return to position so the ice maker senses a full bin and pauses production
• A weakened or missing spring may cause an overfilling ice bucket, a loose arm, or inconsistent ice production
• Replaces damaged or stretched springs that prevent the control rod from moving smoothly

• Unplug the refrigerator and shut off water to the ice maker
• Empty the ice bin and access the shutoff arm pivot
• Note the spring's orientation; install with needle-nose pliers without bending the control rod
• Restore power/water and verify smooth arm movement and proper shutoff

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.

A replacement tension spring used to restore normal movement and positioning for the affected appliance component. Replaces a worn or broken spring to help parts return to their intended position and reduce loose or uneven operation. What it does:

• Provides tension or counter-force for a door, drawer or linkage so the part moves smoothly and returns to position.
• Restores alignment and prevents sagging, slamming, or parts that don't stay in place.
• Reduces noise and uneven movement caused by a stretched or broken spring.
• Useful when a worn spring causes intermittent operation or poor component response.

• Disconnect power and water before servicing. Wear eye protection and gloves — springs can release suddenly.
• Inspect mounting points, clips and anchors; replace any damaged hardware to ensure proper function.
• Use appropriate tools (needle-nose pliers, spring hook) and follow OEM instructions for safe installation.