Electrolux Support Parts

The Shock Absorber Kit is an OEM part for Frigidaire washing machines. It is a comprehensive kit that includes 2 shock absorbers, 1 locking pin, 4 lock nuts, and a set of instructions. These shock absorbers play a vital role in reducing vibrations and absorbing shocks during the washing cycle, providing stability and minimizing excessive movement.

Causes of a bad shock absorber can include wear and tear over time, exposure to heavy loads or unbalanced loads that put excessive strain on the absorbers, or damage due to impact or mishandling.

Symptoms of a bad Shock Absorber include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises
• The washer moving or walking during the operation
• Leaks due to increased stress on the tub and other components

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This rear shock absorber kit stabilizes the washer tub by damping movement and vibration. Replacing a worn shock restores smoother, quieter spins and helps prevent the drum from banging the cabinet or the machine from walking. What it does:

• Dampens tub movement to control vibration during wash and spin
• Helps prevent banging/thumping noises and cabinet contact
• Reduces "walking" or excessive shaking of the washer
• Can help minimize out-of-balance interruptions

• One rear shock absorber kit

• Disconnect power and turn off water before servicing
• Support the tub/drum to relieve load before removing the shock
• Remove retaining pins/bolts; install the new shock in the same orientation and transfer any reusable hardware
• For consistent damping, replacing shocks in pairs or as a complete set is commonly recommended

This front shock absorber kit stabilizes the washer's tub during spin to reduce vibration and noise. Replacing worn dampers helps restore smooth operation and protects the cabinet and suspension from excessive movement.

• Dampens and controls tub movement during wash and spin
• Helps reduce shaking, "walking," and loud thumping/banging noises
• Can help when the washer won't reach or maintain full spin due to imbalance
• Replaces weakened or damaged front shock mounts/dampers

• Disconnect power and water before servicing
• Access shocks per your model's procedure; support the tub to relieve load
• Install with mounts aligned and fasteners tightened securely; verify free tub movement
• Many replace shocks in pairs to maintain balanced damping

Note: This is one shock absorber, order quantity needed.

The Shock Absorber is an OEM part for Frigidaire washing machines. The shock absorbers play a vital role in reducing vibrations during the spin cycle and absorbing mechanical shocks that occur with imbalanced or off-center loads. Their durable design effectively isolates the external structure from damaging reverberations.

Causes may involve age-related wear that diminishes shock absorbing qualities over thousands of machine cycles. Impact damage or broken mounts could also necessitate replacement. Installing this kit restores a quiet and stable washing performance to the appliance.

Symptoms of a bad shock absorber include:

• Excessive shaking or vibrating during operation, especially spin cycles
• Loud banging or knocking noises from the washer
• The washer moving or walking on the floor during use
• Leaks from external tub connections

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Shock Absorber is an OEM part for Whirlpool brand washing machines. It plays a vital role in reducing vibrations and absorbing shocks during the wash cycle, providing stability and minimizing excessive movement. 

Symptoms of a bad shock absorber include:

• Excessive shaking or vibrating during the wash cycle 
• Loud banging noises
• The washer moving or walking during the operation
• Leaks due to increased stress on the tub and other components

Causes of a bad shock absorber can include wear and tear over time, exposure to heavy loads or unbalanced loads that put excessive strain on the absorbers, or damage due to impact or mishandling. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This trunnion plate secures the washer's inner basket to the drive hub/trunnion, keeping the tub centered and stable during spin. Replace it if the basket feels loose, wobbles, or makes scraping/knocking noises from the hub area. What it does:

• Couples the inner basket to the trunnion/drive hub so the basket spins true
• Helps maintain alignment to reduce vibration and tub-to-basket contact
• Wear can allow play or slippage at the hub connection
• Common symptoms: wobble, scraping/grinding, excessive vibration, poor spin results

• One trunnion plate

• Disconnect power and wear cut-resistant gloves before servicing
• Access typically requires removing the agitator/wash plate and lifting out the inner basket
• Clean and inspect mating surfaces; align the plate correctly and tighten fasteners evenly
• Check related parts for wear and replace if needed

Note: Quantity of two brackets

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

This locking clip secures the fan/blower housing in place to keep the airflow path sealed and stable. Replacing a worn or missing lock helps eliminate rattles and air leaks for consistent, quiet operation. What it does:

• Secures the fan/blower housing to its mounting points to prevent movement
• Helps maintain a tight seal for proper airflow through the exhaust path
• May correct rattling, vibration, or scraping noises from the blower area
• A loose or missing lock can allow the housing to shift, causing air leaks and reduced performance

• Fan housing lock

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the blower/fan housing by removing the appropriate access panel(s)
• Note orientation, then release and replace the lock; ensure the housing seats fully and evenly
• Clear lint from the area and verify the blower wheel spins freely before reassembly and testing

Front plate restores the appliance's front-facing cabinet, protecting internal components and improving appearance. It replaces cracked, dented or worn front trim so the appliance looks finished and covers internal parts. What it does:

• Covers and protects internal components behind the appliance's front cabinet.
• Restores cosmetic appearance when the existing front is dented, cracked, or scratched.
• Helps maintain proper fit and alignment of adjacent trim and access points.
• Reduces exposure of internal components to dust and incidental contact.

• Always disconnect power (and water, if applicable) before beginning work.
• Removal typically requires removing fasteners, clips or adjacent trim panels—keep track of all screws.
• Handle carefully; edges may be sharp and panels can be awkward to position alone.

The Trunnion is an OEM part for Frigidaire washing machines. It allows the outer wash tub to rotate during agitation and the spin cycles. The trunnion is a heavy-duty, durable component designed to withstand the rigors of repeated cycles and turbulent wash motions.

Causes of a bad trunnion can be wear over extended use, damage from unbalanced loads that strain the pivot point, or fractures from impact or manual mishandling.

Symptoms of a bad trunnion include:

• Excessive vibration or shaking during operation
• Noisy or grinding sounds emanating from the tub area
• Difficulty starting or stopping tub motions
• The tub failing to rotate properly during cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This support is a molded mounting bracket designed to secure and stabilize appliance components, helping keep parts properly aligned and preventing sagging or movement during use. Durable plastic construction for reliable long-term positioning. What it does:

• Secures panels, assemblies, or internal components to the cabinet or frame
• Keeps parts aligned to prevent binding, rubbing, or uneven wear
• Supports weight to reduce stress on fasteners and adjacent parts
• Helps restore original fit and function after breakage or loss

• One support mounting bracket

• Disconnect power and, if applicable, water before beginning any repair
• Confirm correct orientation and seating before fastening; use factory screw locations
• Use appropriate, non-stripping fasteners and do not overtighten
• If the original part is damaged, remove all debris before installing new support