Need Help?
Call or text
The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum.
Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.
Symptoms of a bad seal include:
This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more
If your gas burners won't light or igniters aren't sparking, the spark module likely needs replacement. DIY-friendly repair, typically 10-15 minutes.
I tried swapping the cables around by putting the cables from the burners that would light onto the ones that didn't light. When I did that the problem would move. So this is how i determined that the issue was with this module and not the burners or cables. Once this new module arrived it was simple to disconnect the old one and put the cables back on the new one. I tested it (holding by breath!) and then all of the burners started. HOORAY! Read more
Replacement drip pan installs below range surface burners to catch spills. Replace if rusted, discolored, scorched, or coated with buildup that won't clean.
Burner element was broken and partially melted. Didn't know if element or switch or kettle started it. Switch smelled burnt and bad; "burner on" light was on regardless of switch position. Traded with another burner switch; light went out. Ordered new infinity switch, burner element, plug for burner element, & drip pan. Watched Appliance Parts Pros videos (the plug one simplified that part). Replaced items. Range works fine. Received parts in one day with regular shipping. Great service! Read more
Integrated ignitor and orifice assembly for gas range burners. Replace when ignitor electrodes are damaged, orifice threads are stripped, or mounting holes are worn.
Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more
Burner cap covers the burner head on gas ranges and cooktops. Replace if cracked, chipped, broken, or missing to protect burner and ensure proper heat.
Ordered replacement parts Read more
Oven won't heat to correct temperature or won't turn off? The thermostat regulates oven heat. DIY repair typically takes 15-60 minutes with basic tools.
Removed old thermostat and pulled old thermocouple fron oven. ran new thermocouple to oven and put in clip, tistalled new thermostat using 2 phillips head screws, done. Read more
The Igniter and Orifice Assembly is an OEM part for Frigidaire ranges and cooktops, designed to provide a reliable source of ignition for the gas burners. This assembly includes the igniter, which produces a spark to light the gas, and the orifice, which controls the flow of gas to the burner.
Causes for replacement may include wear and tear on the igniter, clogging or damage to the orifice, or electrical failures that prevent the igniter from sparking.
Symptoms of a bad Igniter and Orifice Assembly include:
This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.
Replaced igniter and orifice assembly, and replaced spark module. Used the video for help, but the video doesn't show the top cover piece that needs to be taken off first. Also the screws for the igniter set were stuck from old grease or something and had to be drilled out. Overall the project was well worth my time for the cost vs replacement decision. AppliancePartsPros.com makes it so easy to choose a part and guesstimate the probably of choosing the right one. Read more
The Overlay is an OEM part for Frigidaire ranges. It is the control panel's interface layer, displaying the various functions and settings available for the range. This component is crucial for selecting and controlling the appliance's operations, ensuring user-friendly interaction with the cooking settings.
Common causes of a bad overlay include regular wear and tear, exposure to heat, or accidental damage.
Symptoms of a bad overlay include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Order the part from you all. Watched the video how to install, which was easy to understand. the part arrived A DAY EARLIER than we expected! How nice is that? and installed part, stove /oven works. everybody's happy. Read more
Gas burners won't ignite and there's no clicking sound? The spark module provides the electrical spark to light all burners. DIY repair in under 1 hour.
Replaced spark module - oven was less than two years old. Like a lot of new gas ovens, turning on any one burner to 'lite' sends sparks to all 5 top burners. The difficulty was getting to the spark module, as some generic videos show access to it from the upper panel on the back of the oven, but it wasn't there. Had to take off the entire top burner panel of the oven to get to the module, and then it was simple to replace the module by transferring the wires to the new one. I did see on... Read more
Oven won't heat or bake properly? A failed bake element is often the cause. This bottom heating element replacement is straightforward—most DIYers complete it in under 30 minutes.
Watched the video here, took the leap that burner was the problem and ordered it. Also found another vid on you tube that was more specific to my Kenmore. Tip: find out how to take off the oven door. For mine it was very easy but not detailed in the APP vid. I followed instructions in APP vid but also first took off back panel of range and tested resistance of old burner to ensure that was truly the problem (as suggested by other YT vid). Also, dis/connecting the wires from the back is easier... Read more
Fix F11 or F13 error codes, blank display, or total control panel failure. This gas range circuit board restores oven timers and functions. DIY-friendly.
We simply removed the back panel off the stove, removed four screws and unplugged the controller. It was so quick and easy. It took about five minutes to replace. Read more
Replacement overlay for range touch pad control panel. Installs over the control board buttons. Replace if cracked, peeling, worn, or labels are faded or illegible.
Turned off the power. Pulled out the stove. Removed back of upper part of stove. Removed old control board. Took photos with phone to make sure I got wires back on correctly. Only 1 wire was difficult to remove and required gentle rocking with pliers. Put the overlay on the new board. Placed all the clips and wires back on the new board. Turned on power to test. Tested ok. Turned power off and resecured the board and back on the stove. Repositioned the stove. Turned power back on. I... Read more
Oven won't light even with glowing igniter? Safety valve controls gas flow to burner. Moderately easy repair with gas line disconnect required.
My tenant thought that the oven safety valve was bad, but after some research, I found that the transfer of heat from the igniter had to be sufficient enough to cause the valve to open.Your agent confirmed this and reassured me that even if the igniter was glowing, there was a 99% chance that it wasn't getting hot enough. I ordered the igniter, and also the safety valve just in case, as we were going to be fixing this on Christmas eve, so the oven could be used for Christmas dinner. Your agent... Read more
Broil element not heating or burned out? This top heating element restores high-heat broiling for browning and crisping. DIY-friendly, 15-30 minute repair.
I replaced the element. I went on your site to order a new element, and had trouble locating the exact replacement. A young man named Kenneth came on live chat and assisted me. He found the correct one and assisted me with the order. It was all very smooth and quick. I received the part in two days ! Read more
Fix sparks, tripped breakers, or burnt connections at your range's power cord junction. Terminal block replacement takes about 5-10 minutes with basic tools.
I unplugged the stove ,cut the 50 amp cord off from the terminal block as it was burned took out the terminal block as it to was all melted .installed the new terminal block with a new stove cord back in business Read more
Replaces damaged or corroded 6-inch drip pan beneath your electric range stovetop element. Catches spills and debris. Install when original is rusted or worn.
I ordered 2 large ones and 2 small ones which arrived earlier than I was expecting. Read more