Estate Parts

• No heat or not enough heat

I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more

Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more

First, just for safety sake, unplug the unit. I took the three screws out of the latch end of the door and pried both the inner (black) frame off and the outer (white frame) being careful not to crack the inner frame as I wanted to reuse it. I removed the screws holding the old handle on and reused them to fit the new handle to the new frame. I then had to take the glass from the broken frame, clean it, and reuse it on the new frame. You need clear silicone sealer to hold the glass firmly in... Read more

Ordered a new one from Appliance Parts Pros.Fast delivery and a great price on the handle. Read more

I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer. Read more

Ordered a replacement panel. Item arrived exactly as described. Used the Youtube instructions. Took all of 5 minutes to replace. Thanks! Read more

After tossing a couple for refrigerators to clean the storage area - we had one good one left taken from an apartment where the resident bought a newer-bigger one. Another resident's went bad - froze in the freezer - but 65 F in the lower refrigerator unit. Not my job but I decided to check it - diassembled the freezer plastic - fan didn't run - took it out and direct powered it - dead! I went on line and reviewed numerous Goolgle hits - yours was easiest to work in - put in the OEM P/N - you... Read more

• Will not stop filling with water
• Will not fill with water

Reviewed troubleshooting tips and identified problem as "water level switch". Watched repair video, which was very helpful. Ordered part on a Sunday, which arrived the following Tuesday. Repair was easy the fix was successful. Read more

Simple replacement of new glass Read more

Replaced water reservoir that had become contaminated with ??? Also had to replace the water filter, because the water contaminated it also. Cost was about $150, for two filters and the reservoir. The first filter was replaced because I did not know the reservoir was contaminated, and no water was coming out of the dispenser. Since the water in the ice maker did not come through the reservoir, there was no smell or contamination there. The new filter enabled water to come through the dispenser,... Read more

• Door won't close

My microwave was stainless steel. I ordered the part for stainless steel, but it was not identical in color. It was black and not the gray color of stainless steel. However, I removed the stainless steel (the actual metallic) frame from my broken grille (bent back a few metal tabs and pried loose the adhesive tape with a putty knife). Then I placed it on my new black plastic part and reassembled to the microwave. I find that it looks perfectly acceptable and maybe even nicer with the black as... Read more

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem. Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light

Called a repairman and he told us we needed to change a bunch of parts and would cost over $400! Decided to do some research online and found suggestions to replace the spark igniter. Decided to give it a try. Took about 10min to replace and oven is now working perfectly, for a total of $30! Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more