Frigidaire Burner & Related Parts

Burner cap sits atop the gas burner base to distribute flame evenly. Replace if cracked, warped, discolored, or missing to restore proper heat distribution.

Surface burner crown that mounts on sealed gas burners to distribute gas through flame ports. Replace if worn, clogged, cracked, or missing.

Replacement surface burner head for gas ranges and cooktops. Distributes gas through precision ports for even flame. Needed when original is clogged, damaged, or corroded.

Replace a gas range burner valve that's broken, stuck open, or causing hard-to-adjust flames. Moderate DIY repair requires raising the stovetop.

Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.

This is a top burner gas valve that controls the flow of gas to a surface burner on a gas range. It connects to the burner control knob and regulates the flame from low to high settings. Replace this valve if a surface burner won't ignite, the flame is difficult to adjust, or you detect a gas smell even when the knob is in the off position.

This is the bake burner tube located inside the bottom of the oven cavity in a gas range. It distributes gas evenly to produce a consistent flame for baking and roasting. Replace this burner tube if you notice uneven heating, weak or irregular flames, or visible damage such as corrosion or holes in the tube.

Burner base mounts and houses the gas burner on your cooktop surface. Replace if cracked, discolored, or damaged to restore proper burner placement.

Replace a cracked, chipped, or missing burner cap on your gas range or cooktop. Restores a clean look and protects the burner assembly underneath.

Surface burner cap sits atop the burner head to shape and center the flame. Replace if cracked, chipped, or missing to restore proper flame distribution.

This is the gas supply tube that delivers fuel from the gas valve to the bake burner at the bottom of a gas range oven. It may include the orifice fitting that meters the correct gas flow for proper combustion. Replace this tube assembly if you notice uneven oven heating, a weak or absent bake burner flame, or if you detect a gas odor indicating a cracked or damaged supply tube.

Replacement surface burner for gas range cooktops. Installs directly onto the burner base. Order when your existing burner is cracked, clogged, or missing.

This is a black burner cap that sits on top of a gas range surface burner head. It distributes the gas flame evenly around the burner for consistent heating. Replace this cap if it is cracked, chipped, warped, or heavily corroded, which can cause uneven flames, poor ignition, or yellow/orange flame color.

Natural gas burner orifice meters gas flow to range burners. Replace worn or clogged orifices for stable flame. Used for LP to natural gas conversions.

The Burner Valve is an OEM component specifically designed for Frigidaire ranges. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Causes of a bad burner valve can include wear over extended usage periods, damage from water, or gas blockage impeding operation. 

Symptoms of a bad burner valve include:

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance  
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Replacing with this OEM valve restores full functionality to the range cooktop. Compatible with existing gas lines, it supports safe and reliable cooking performance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.
 

This valve-to-regulator tube carries fuel between the pressure regulator and gas control valve, maintaining a sealed path for proper ignition and stable flame. Replace if the tube is kinked, damaged, or leaking.

• Provides a rigid, factory-formed connection between the pressure regulator and valve
• Helps ensure correct gas flow to the burner system
• Failure signs include weak or no flame, delayed ignition, repeated clicking, or a gas odor
• Visible kinks, corrosion, or stripped fittings indicate the tube should be replaced

• Disconnect power and shut off the gas supply; ventilate the area before servicing
• Use two wrenches to back up fittings; avoid twisting the regulator or valve bodies
• Route the tube without kinks and tighten flare connections securely
• Leak-test all joints with an approved solution—never an open flame—before restoring service.