Frigidaire Burner & Related Parts

The Burner Cap is an OEM replacement part that fits Frigidaire ranges. It is responsible for covering the small burner igniter on the cooktop. Over time, the cap can become damaged from heat exposure and food debris. Causes of failure include cracking, warping, and corrosion. 

Symptoms of a bad burner cap include:

• Uneven or abnormal flame
• Ignition issues
• Improper fit and wobbling

This burner cap is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, and Kenmore ranges.

The Regulator is an OEM part for Frigidaire cooktops. It is responsible for regulating the flow and pressure of gas entering the appliance, ensuring safe and efficient operation.

A bad regulator can be caused by faulty internal components, wear and tear over time, or damage due to improper handling. Signs of a faulty regulator include uneven heating, weak flame, or gas leaks.

Symptoms of a bad regulator can include:

• Uneven heating of burners or oven 
• Weak or inconsistent flame 
• Gas leaks around the regulator 

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This genuine replacement cap restores a clean, finished look and helps protect the underlying fastener or opening on your appliance. Replace a missing or damaged cap to keep components covered and looking factory-fresh.

• Covers and protects an exposed screw, hinge, or opening from dust and debris
• Restores the appliance's finished appearance
• Helps maintain secure retention of the underlying component
• Common signs of failure: missing or broken cap, cap won't stay in place, cosmetic wear, visible exposed fastener/opening

• Disconnect power before servicing; if working near water or gas lines, shut those off as applicable
• Gently pry off the old cap; avoid scratching surrounding surfaces
• Align and press the new cap until it seats/snaps securely

This small cap snaps into the center of a control knob. It refreshes the appearance and helps keep moisture and debris out of the knob interior so the control stays protected and easy to use. What it does:

• Provides a finished cover for the center of a control knob
• Helps protect the knob interior from spills and debris
• Restores a clean look when the original cap is missing or damaged
• Addresses a loose or rattling knob insert

• 1 control knob cap

• Disconnect power to the appliance for safety before working near controls
• Pull the knob straight off the control shaft; remove any remnants of the old cap
• Align tabs and snap the new cap into the knob firmly
• Reinstall the knob on the shaft and verify smooth operation

The Surface Burner Cap is an OEM part for Frigidaire ranges. It fits over the surface burner, providing a protective cover while ensuring proper gas flow and flame distribution.

A bad surface burner cap can be caused by wear and tear, damage, or improper cleaning. When the burner cap becomes faulty, it can result in issues such as uneven flames, inefficient heating, or difficulty in maintaining a consistent temperature.

Symptoms of a bad surface burner cap include:

• Uneven or flickering flames
• Difficulty in reaching desired temperatures
• Excessive gas odor during burner operation

Replace your faulty surface burner cap with this genuine OEM Frigidaire part to restore your cooktop. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

LP Conversion Kit lets you convert a natural-gas cooktop or range to run on propane (LP), helping burners operate safely at the correct orifice size and pressure. Use the kit when changing fuel type or when burner flames perform poorly. What it does:

• Converts burner fuel delivery so the appliance can operate on propane (LP).
• Restores expected flame shape and heat output after switching fuel types.
• Helps address ignition issues, sputtering, weak flames, or yellow/tall flames caused by incorrect orifice sizing.
• Ensures the appliance meets manufacturer fuel-type requirements when properly converted.

• Follow the manufacturer's LP conversion instructions exactly; improper conversion can be hazardous.
• Shut off gas supply and disconnect power before starting; test all connections for leaks after installation.
• Keep the kit parts and conversion instructions for future service or warranty reference.

Protective cap that covers a terminal or post on select Frigidaire appliances, helping keep dirt, moisture and accidental contact away from electrical connections for safer operation and longer component life. What it does:

• Covers and protects electrical terminals/posts from dust, moisture and corrosion
• Helps reduce the risk of shorting from accidental contact with nearby metal parts
• Maintains a secure, insulated connection where a terminal or post is exposed
• Useful when replacing damaged or missing covers to restore normal protection

• Disconnect power to the appliance before inspecting or replacing electrical components
• Remove the old or damaged cap and press the replacement firmly over the terminal/post until fully seated
• Inspect surrounding wiring and terminals for corrosion or damage; replace if needed

The Burner Cap is an OEM replacement part that fits Frigidaire ranges. It is responsible for covering the medium burner igniter on the cooktop. Over time, the cap can become damaged from heat exposure and food debris. Causes of failure include cracking, warping, and corrosion. 

Symptoms of a failing medium burner cap include:

• Uneven or abnormal flame
• Ignition issues
• Improper fit and instability

This cap is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, and Kenmore ranges

This replacement cap covers and protects a small opening or fastener on your appliance. It restores a clean, finished appearance and helps keep out dust and moisture when the original cap is missing or damaged. What it does:

• Covers a screw hole or open end as designed on the unit
• Helps block debris and moisture and can reduce rattles
• Maintains a clean, finished look and protects underlying hardware
• Replace if the original cap is cracked, loose, deformed, or missing

• 1 cap

• Disconnect power and allow any hot surfaces to cool before servicing
• Use a non-marring tool to gently remove the old cap to avoid scratching
• Align and press/snap the new cap into place; do not force
• If the cap conceals a fastener, the fastener is secure before reinstalling the cap

This surface burner cap sits atop the gas burner head to distribute flame evenly and protect the burner from spills, helping restore steady flames and reliable ignition when the original cap is worn, warped, or missing.

• Distributes flame for more even heating across cookware
• Shields the burner head from boil-overs and debris
• Supports proper ignition when correctly seated and level
• Common signs it's needed: missing cap, chips/cracks, warping, uneven or yellow flames

• Allow the cooktop to cool completely; shut off gas/power if performing additional service
• Remove the grate, lift off the old cap, and clean the burner head surface
• Center the new cap on the burner head so it sits flat and does not rock
• Test the burner; if ignition is delayed or flames are uneven, reseat the cap

Restore strong, even flame on your large burner. This sealed burner head replaces the 12K position on gas ranges/cooktops, helping recover reliable lighting and consistent heat when the original head is clogged, corroded, or damaged.

• Directs gas through calibrated ports to deliver a stable, even flame on the 12K burner position
• Helps address: burner won't light or lights intermittently; weak, uneven, or yellow flames; flame lifting or sputtering
• Replace when ports are clogged beyond cleaning, or the head is warped, cracked, or corroded
• Seats over the orifice and spark igniter in sealed-burner designs

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove grate and cap; lift off or unthread the old head, retaining any mounting screw
• Clean the mating surface; align the new head over the orifice and igniter so it sits flat; if screw-retained, tighten snugly only
• Reinstall cap and grate; restore gas/power and confirm proper ignition and flame

This replacement cap covers and protects its designated opening or fastener on your appliance. It restores a clean, finished look and helps shield internal areas from dust and wear when the original cap is missing or damaged. What it does:

• Covers a specific opening, fastener, or trim end to protect the area
• Helps keep moisture, grease, and debris out of the assembly
• Restores proper fit and finished appearance
• Typical symptoms include a cracked, loose, discolored, or missing cap

• 1 cap

• Disconnect power and, if applicable, shut off gas/water before servicing
• Note the cap's orientation; gently unclip, pry, or unthread the original per model design
• Seat the new cap fully and avoid forcing or overtightening
• The cap is secure and does not interfere with moving parts

Replacement snap-on cap that restores a finished appearance and helps protect underlying components from dirt and accidental contact. Fits original mounting locations to cover exposed hardware and improve appliance safety and aesthetics. What it does:

• Covers and protects exposed hardware, terminals or posts to reduce debris buildup and accidental contact.
• Restores a clean, finished look to panels, trim or appliance edges.
• Helps reduce rattling or vibration noise caused by missing trim pieces.
• Use when the original cap is cracked, broken, missing or when exposed fasteners are visible.

• Always disconnect power (and water, if applicable) before attempting any repair.
• Remove the damaged cap by hand or with a small pry tool; press the replacement cap onto the mounting post until fully seated.
• Avoid excessive force during removal/installation to prevent damage to the mounting post or surrounding trim.
• If mounting posts or clips are damaged, replace those components to ensure a secure fit.

This burner cap sits on top of a gas cooktop surface burner to shape and protect the flame for even heating and safe operation. It restores proper flame pattern and helps keep the burner head clean. What it does:

• Covers the burner head to direct gas flow and create an even flame
• Helps prevent food and spills from clogging the burner ports
• Can improve ignition consistency and reduce yellow or uneven flames
• Replaces cracked, warped, or missing caps that cause poor heat distribution

• One replacement burner cap

• Ensure the appliance is OFF and completely cool before servicing
• Lift off the old cap and set the new cap in the correct position on the burner head
• No special tools required; verify the cap sits flat and centered before use
• Inspect for cracks or heavy corrosion; replace if damaged

The Gas Burner is an OEM replacement part for Frigidaire gas wall ovens and cooktops. It facilitates safe and efficient cooking by providing a controlled source of flame. 

Symptoms of a bad gas burner include: 

• Uneven or unpredictable heating across the burner surfacea
• Flames not igniting or not staying ignited
• Burner components cracking, rusting, or becoming discolored
• Gas smells coming from the burner area

Causes of gas burner issues can be wear over time, contamination of ports/orifices affecting gas flow, or damage to ignition components. Ceramic burner materials may also degrade with heavy use or exposure.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.