Frigidaire Guard, Shield, Barrier Parts

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Wave Guide Cover is an OEM part for Frigidaire microwaves. The cover prevents food particles and moisture from entering the wave guide, helping to maintain the efficiency and safety of the microwave.

Causes of a bad wave guide cover can include exposure to high heat, splatters from food and liquids, or regular wear and tear. 

Symptoms of a bad wave guide cover include:

• Sparks or arcing inside the microwave
• Uneven cooking or heating
• Visible burns, cracks, or discoloration on the cover
• Noise or rattling sounds during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement cover restores a clean, secure fit over an opening on your appliance, helping shield internal components from dust, moisture, and debris. Replace a damaged or missing cover to maintain proper protection and appearance. What it does:

• Shields internal parts from grease, dust, and debris intrusion
• Helps maintain proper airflow and component protection as designed
• Reduces vibration or rattling from loose or broken panels
• Restores a finished, factory look when the original is cracked or missing

• 1 cover

• Disconnect power to the appliance before servicing
• Note fastener locations and orientation for correct reinstallation
• Reuse original screws/clips unless your unit specifies otherwise
• Use gloves and caution—panel edges and surrounding metal can be sharp

This replacement water tube routes water within the refrigerator's internal water system. Installing a fresh, intact tube helps stop leaks and restores reliable water flow to the dispenser and ice maker. What it does:

• Carries water between components such as the inlet valve, reservoir, dispenser, and ice maker
• Maintains a sealed, kink-free path for proper flow and pressure
• Common signs of failure: leaks or puddling, weak or no dispenser flow, ice maker not filling, brittle or discolored tubing

• One tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the original routing; take photos to match length and path
• If trimming, cut ends square and fully seat into the existing push-to-connect or compression fittings
• Restore water and check all connections for leaks before powering the unit back on

This replacement cover is a protective panel used in the microwave assembly. It shields internal components from grease and debris and restores a clean, secure barrier when the original cover is cracked, burned, or missing.

• Shields internal components from food splatter, steam, and grease
• Helps maintain proper airflow and safe operation inside the cavity
• Common signs it's needed: cover is warped, cracked, scorched, loose, or missing
• Reduces arcing/sparking or buzzing caused by a damaged or contaminated cover

• Disconnect power before servicing; allow hot surfaces to cool
• Remove screws or release tabs to take off the damaged cover; reuse existing hardware if applicable
• Clean surrounding area to remove grease or debris, then seat the new cover fully and secure without overtightening
• For microwaves, internal high voltage can remain even when unplugged.

This mullion guide secures and aligns the refrigerator's vertical door trim so doors close evenly and seals engage properly. Replacing a worn or broken guide helps restore door alignment and reduce drafts at the center seam. What it does:

• Holds the mullion/vertical trim in place and keeps the trim flush with the cabinet
• Guides the doors during closing to maintain even gaps and seal contact
• Prevents the mullion from shifting, rattling, or catching when doors open or close
• Common symptom: loose, misaligned, or damaged center trim causing wind, noise, or uneven door gaps

• Disconnect power before starting service and work on a stable surface
• Remove the mullion/trim and any surrounding gaskets or screws as needed to access the guide
• Use appropriate trim/removal tools to avoid damaging adjacent plastic or gasket material
• Reinstall hardware securely and verify doors close and seals engage properly after installation

This replacement extension support restores proper alignment and secure mounting for the appliance component it attaches to, helping stop misalignment, rubbing, or loose parts and letting the appliance operate smoothly. What it does:

• Replaces a worn, broken or missing extension support used to secure or extend a nearby panel, drawer, or assembly.
• Helps stop rattling, uneven movement, or binding caused by a damaged support piece.
• Restores proper spacing and mounting so associated parts track and close correctly.
• Works as a direct-fit replacement when the original extension is damaged or missing.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle edges carefully; use basic hand tools and keep original fasteners if reusing them.
• If mounting hardware is missing or damaged, source matching screws/clips separately.

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

A replacement protective shield that covers and protects internal appliance components from debris, moisture and incidental contact. Restores protection to damaged or missing shields to help maintain safe, reliable operation. What it does:

• Covers and protects wiring, connectors or nearby parts from accidental contact and debris
• Helps prevent moisture or food particles from reaching sensitive components
• Replace if the shield is cracked, warped, missing or allows exposed parts
• Reduce rattles or contact-related noises caused by loose or damaged shields

• Shield

• Disconnect power to the appliance before starting any repair
• Use care around sharp edges; wear gloves and eye protection
• Remove fasteners holding the old shield; reuse or replace screws as specified by the manufacturer

This small replacement sleeve protects and guides a moving component in the appliance to reduce wear and ensure smoother operation. It helps maintain correct alignment where parts slide or rotate, preventing metal-on-metal contact. What it does:

• Acts as a protective liner or guide for a rotating or sliding shaft or pin
• Reduces wear and friction between mating parts
• Helps stop scraping, squeaking, or uneven movement around the fitted area
• Supports proper part alignment for reliable operation

• One replacement sleeve as shown

• Replace only with the exact part number to ensure correct fit
• Inspect mating shaft/pin for wear and clean before installing the sleeve
• Apply light lubricant only if specified by the manufacturer; avoid over-lubrication
• Disconnect power and follow all safety guidelines before servicing the appliance

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners