Frigidaire Igniter

• Gas smell
• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

My Tappan Range, which I paid a grand total of $65.00 for, and have been using since Katrina, (Katrina in 2005 is how we measure time in South Mississippi.) I live in an old house, and I am old, too. Last winter was the coldest I can remember, and my husband (older than I and far more hard-headed) used the oven like a heater. I read all user's manuals, because I use only used stuff, I can download the manuals or read them online, and it clearly stated in there NOT to use the oven as a... Read more

My Kenmore 790.74139310 gas range was taking over 30 minutes to reach 350F. It used to take a little less than 10 minutes. The problem was the ignitor for the lower gas burner. It would glow but not pass sufficient current to increase the gas flow to the lower burner. Once at temperature, there is of course loss of heat when loading the oven with room temperature food. This took too long to recover, so we did not have proper temperature for proper cooking for the first 30 to 40 minutes. Food... Read more

Replaced igniter. Problems solved. Read more

Replaced ignitor. Very simple project. Read more

I have used this site before to fix my dishwasher, so I knew to check here first. I searched other's comments to troubleshoot my problem. Ordered the part and it arrived in only a couple of days. I should insert here that I am a 45 yo female, so if I could do this, anyone can. I watched the video and proceeded to replace the part. For my particular model, I didn't access the part from the back, but instead through the underside by removing the bottom drawer. Total from start to finish... Read more

Removed the bottom tin work in the oven and removed the burner tube. Tried to remove the igniter bracket but the screws were too tight for the Phillips head and couldn't get vice grips to clamp on the head, so I bent the bracket enough to remove and replace the igniter. Then reassembled. I give AppliancePros.com a 5 star rating. Site was easy to use, the part was delivered in under 2 days, and it was the correct part packaged carefully so the igniter was protected from breaking. Read more

• Won't start

This is a Montgomery Ward gas range made by Tappan. Parts are no longer offered for this appliance. So, I had to eyeball various ignitors to determine which one would work. I settled on the least expensive one and ordered two (Just in case there were "issues"). The parts arrived quickly but were not a simple drop-in replacement. The new ones were longer and smaller in diameter. I had to use the original bracket because it provided the electrical ground for the spark. I used a spring to... Read more

I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more

• No heat or not enough heat

Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more

Replaced all ignitors. Read more

We ordered a new ignitor and it came in two days just as promised. The only problem that we experienced was that the leads on the new ignitor were to short. We were able to find enough slack on the oven end to make it work. The oven is once again working great. The video was a little off on what need to be done to disconnect the ignitor. We actually had to flip the oven over to get to the bottom. We could not access the connector through the back. Read more

Read the reviews on your site and watched your video and decided it was worth a try to fix rather than to replace stove. Ordered the igniter for the oven then I also ordered the igniter for the broiler as it was sluggish as well. When you go, go all the way. Only problem I had was with the wire nuts, wish that something more substantial was provided. Got the stuff quickly, as promised and installed as per video and oven and broiler work like new. Thanks!!!!! Read more

As recommended in your repair video the likely cause was increased resistance in the igniter. Although I could not match the part by oven model number because of its age, I queried your site for oven igniters and matched the part by photo and description. The part that arrived was an exact match. After installation, the oven worked perfect both on auto and manual settings. Read more