Frigidaire Dishwasher Dishrack

The Rack Assembly is an OEM part for Frigidaire dishwashers. This assembly provides a stable and organized space for placing dishes, glasses, and utensils during the dishwashing cycle. 

Causes of a bad rack assembly can include rust or corrosion from prolonged exposure to water, physical damage from heavy or improperly placed items, and wear and tear over time. 

Symptoms of a bad rack assembly include:

• Dishes not staying securely in place
• Visible rust or corrosion
• Broken or bent tines
• Difficulty sliding the rack in and out

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This dishwasher rack tine row bracket secures the fold-down tine row to the rack so it pivots and locks correctly. Replacing a cracked or missing bracket helps restore stable plate support and smooth loading.

• Secures the fold-down tine row to the dishrack
• Allows the tine row to pivot between upright and flat positions
• Helps keep dishes from tipping during cycles
• Common symptoms: tines won't stay up, row flops loosely, bracket is cracked/missing

• Disconnect power to the dishwasher before servicing
• Pull out the rack and locate the affected fold-down tine row
• Release the old bracket and snap the new bracket onto the rack wires
• Verify the tine row pivots and latches smoothly before returning the rack

This replacement basket restores organized storage inside your appliance. It securely holds items in place to prevent tipping or falling through, helping you load, access, and clean with confidence.

• Provides a dedicated compartment to keep smaller items contained and upright
• Replaces a cracked, warped, or missing basket
• Helps prevent items from contacting moving parts or obstructing spray/airflow
• Common signs it's time to replace: broken tabs, split seams, or the basket no longer seats correctly

• Disconnect power before servicing
• Open the appliance and remove the old basket; retain any reusable brackets or rack components
• Seat the new basket fully into its designated location
• Do not overload; verify it's stable and clears moving parts before use

This is the complete lower dishrack that slides in and out on the tub rails. It provides a stable place to load plates, bowls, and larger cookware on the bottom level and restores smooth rolling and proper dish placement when the original rack is worn or damaged.

• Holds and organizes dishes on the lower level of the dishwasher
• Restores smooth rolling and proper alignment of the lower rack
• Common failure signs include broken or rusted tines, wobbling or derailed rack, and difficulty rolling the rack in/out
• Helps when dishes are not staying in place or the rack no longer supports loads properly

• Disconnect power before servicing
• Pull the old rack straight out of the tub; transfer any usable accessories if applicable
• Slide the new rack onto the existing rail tracks; ensure wheels are seated on both sides
• Test smooth movement and clear door closure before running a cycle

Used on the upper rack track

This small retainer clip secures a mating part in the correct position inside your appliance, helping prevent movement, premature wear, and noise. Replace a cracked, bent, or missing clip to restore a tight, reliable hold.

• Provides a positive hold to keep the component properly seated
• Maintains alignment to reduce vibration and rattling during operation
• Helps prevent parts from backing out or disconnecting over time
• Common signs of failure: loose or misaligned component, rattling, clip that falls off, or visible damage

• Disconnect power; if working near any water connections, also shut off the water supply
• Note the clip's original orientation and position before removal
• Use needle-nose pliers or a small flat-blade screwdriver to release/install; avoid deforming mating tabs
• Ensure full engagement and that the secured part is firmly held before reassembly and testing

The Rack Stop is an OEM part for Frigidaire dishwashers. It serves an important purpose by preventing loaded dishes from shifting forward during wash cycles.

Causes of a bad rack stop can include wear and tear from regularly loading and unloading dishes, as well as minor impacts that cause cracks or breaks. Over time, the mounting screws may also loosen.

Symptoms of a bad rack stop include:

• Dishes shifting forward during wash cycles
• Gaps appearing around the dish rack where dishes are not fully secured
• Noise from dishes banging together or rattling around more than usual
• Potential damage to more delicate dishware

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This mounting bracket secures a small appliance component in place to restore proper alignment and stable operation. It provides a simple, durable replacement for worn or broken mounting points. What it does:

• Secures internal components or assemblies to the cabinet or frame to prevent movement
• Restores proper alignment so linked mechanisms operate smoothly
• Helps stop rattling or loose parts that occur when the original holder breaks
• Fits in the original mounting location and works with the appliance's factory hardware

• One replacement holder/mounting bracket as pictured

• High-level replacement — typically accessed by removing the related cover or panel
• Use appropriate hand tools; keep fasteners organized for reassembly
• Disconnect power (unplug appliance or shut off circuit) before starting any repair

This replacement refrigerator door handle restores a secure grip for opening and closing the fridge. It replaces a cracked, loose, worn or broken handle so the door operates safely and looks finished. What it does:

• Provides a sturdy grip to open and close the refrigerator door
• Replaces handles that are cracked, chipped, loose or no longer secure
• Helps maintain proper door alignment and a finished exterior appearance
• Prevents further damage from using a compromised handle

• Check that this handle matches the mounting holes and orientation on your door before installation
• Tighten screws evenly; over-tightening may crack plastic components
• Disconnect power to the appliance before working in tight areas or near electrical components as a precaution