Frigidaire Dishwasher Gasket & Seal

This O-ring is a small rubber seal that restores a watertight connection at a plumbing or valve joint, helping stop drips and leaks and keep your appliance operating normally. What it does:

• Provides a flexible, compressible seal between two mating parts to prevent water leaks
• Commonly used on valve fittings, hose connections, and dispenser plumbing
• Symptoms a failing O-ring can cause: visible dripping, pooled water, or intermittent water flow
• Small, low-cost part that often resolves minor leaks when the correct size is used

• Turn off water supply (and power if applicable) before replacing the O-ring
• Remove the old O-ring and inspect mating surfaces for damage or debris; clean before installing the new ring
• Do not reuse a deformed or torn O-ring; install the correct size and seat it evenly
• After installation, restore water and check the connection for leaks; tighten fittings only as needed to avoid crushing the O-ring

This support is a replacement mounting bracket that helps secure internal components and keeps assemblies aligned for reliable operation. It restores proper fit and reduces noise caused by loose or shifted parts. What it does:

• Secures and stabilizes appliance panels or assemblies to prevent movement and rattling
• Restores proper alignment of connected components to improve operation
• Helps stop vibrations that can cause noise or wear on adjacent parts
• Common symptom fix: loose, cracked, or missing support causing rattling, misalignment, or unstable panels

• One support mounting bracket as shown

• Disconnect power to the appliance before starting any repair
• Use appropriate hand tools and keep fasteners organized during disassembly
• Inspect neighboring clips, screws, and mounting points; replace if damaged

Dishwasher door gasket seals the door to prevent water leaks. Replace if you notice leaking, worn edges, or poor sealing. Verify fit with your model.

Replace your dishwasher's O-ring seal to stop leaks and maintain proper water pressure. This wear part prevents water damage when worn or cracked.

Creates an airtight seal around your dishwasher door to prevent water leaks and improve cleaning performance. Replace when torn, cracked, or loose.

Dishwasher o-ring seal prevents leaks around pump and spray arm assemblies. Replace when cracked, brittle, or leaking occurs. Verify fit by model number.

Dishwasher O-ring seal prevents leaks in pump assemblies and spray arms. Replace when worn, cracked, or leaking. Verify fit with your model number.

Replace your dishwasher's O-ring seal to prevent leaks and maintain proper water flow. Essential when you notice dripping or moisture buildup. Verify fit with your model number before ordering.

Dishwasher door gasket foam creates a watertight seal to prevent leaks. Replace if you notice water escaping or the foam is compressed or torn.

This refrigerator door gasket creates an airtight seal around the door to help maintain proper temperature and energy efficiency. Replacing a damaged gasket restores sealing performance and helps prevent cold air loss. What it does

• Seals the refrigerator compartment to keep cold air in and warm air out
• Helps maintain consistent cooling and reduces frosting/condensation
• Prevents food spoilage related to poor door sealing
• Reduces excessive run time caused by air leaks

• One door gasket as shown

• Clean and dry the door frame before installing to ensure a proper seal
• Soften the gasket in warm water or use a hair dryer on low to ease positioning if needed
• Start installation at the corners, working around the door to seat the gasket evenly

This is a replacement O-ring seal designed to restore a watertight connection in compatible refrigerator water and ice system fittings. It helps stop leaks and prevents water damage when the seal is worn or damaged. What it does:

• Provides a compressible seal between mating water/valve fittings to prevent leaks
• Commonly replaced when fittings drip, puddle, or show visible seal wear
• Restores proper sealing for water supply, ice maker, or dispenser connections
• Small rubber part that maintains pressure integrity at a joint

• Turn off water supply and unplug the appliance before replacing the O-ring
• Inspect mating surfaces and replace any damaged fittings before installing the new O-ring
• Re-seat the O-ring carefully—avoid twisting or pinching the seal during installation