Frigidaire Dishwasher Parts

Retainer clip secures dishrack components in position. Replace if your dishwasher's clip is cracked, bent, or missing to restore proper fit.

This is the user control and display board located on the front panel of the dishwasher. It contains the buttons, display, and interface circuitry that allow you to select wash cycles, options, and monitor cycle status. Replace this board if the display is blank or flickering, buttons are unresponsive, or the dishwasher does not respond to cycle selections.

Front-mounted dishwasher control panel with touch pad buttons and display. Replace when buttons stop responding, panel is cracked, or display is damaged.

Fix a dishwasher that won't drain or leaves standing water. This drain pump assembly removes water at cycle end. Moderate DIY repair, 30-45 minutes.

This spray arm assembly distributes high-pressure wash water inside the dishwasher and spins to cover the racks. Replacing a cracked or clogged arm restores proper spray coverage for cleaner dishes and consistent wash performance. What it does:

• Rotates as water flows to spray dishes evenly across the tub
• Channels water from the circulation pump through precision jets
• Helps resolve poor cleaning results or spots left on dishes
• Addresses issues like a spray arm that won't spin, clogged nozzles, or visible damage

• 1 spray arm assembly

• Disconnect power at the breaker and turn off the water supply before servicing
• Remove the rack if needed to access the arm
• Release the locking tabs or unthread the retaining cap to remove the old arm
• Seat the new arm fully, secure the retainer, and confirm it spins freely before a test cycle

Secures dishwasher thermostat to base for accurate temperature sensing. Replace if loose or broken to prevent overheating. Verify fit by model number.

Dishwasher stuck mid-cycle or won't start? This control board manages cycle timing and operation. Intermediate DIY repair restores normal function.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Fix a dishwasher that won't start when the door is closed. This door latch assembly engages the closure mechanism so your unit recognizes the door is secure.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

If your dishwasher won't start, cycles won't advance, or buttons don't respond, the control board may have failed. This board regulates all functions.

Replacement screw for dishwashers. Secures panels, brackets, and trim to keep components properly aligned. Replace missing, stripped, or corroded screws.

Tension spring that mounts on the side of your dishwasher to control door movement. Replace if broken, worn, or missing to restore smooth operation.

Black

Fix a dishwasher that won't start, has no lights, or only runs certain cycles. This switch assembly restores proper signaling to the control board.