Frigidaire Refrigerator Dispenser Parts

The Dispenser Module is an OEM part for Frigidaire refrigerators. It is a component located within the refrigerator door that is responsible for dispensing water and ice. The dispenser module houses the necessary valve assemblies, sensors, actuators and tubing required to deliver chilled water and ice on demand when the dispenser lever is engaged. It is designed to seamlessly integrate within the refrigerator door panel for convenient access.

Causes of a bad dispenser module can include buildup of mineral deposits or contaminants within the internal components that disrupt water flow or sensor functions over time. Mechanical wear and tear of plastic or rubber seals and valves is also common.

Symptoms of a bad dispenser module include:

• Slow or intermittent water flow from the dispenser
• Ice cubes dispensed one at a time instead of in batches
• Water or ice dispensing that doesn't work at all
• Leaks or water droplets below the dispenser area
• Error codes related to the dispenser on the control board

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This refrigerator dispenser actuator is the paddle/lever you press with your glass to start ice or water dispensing. Replacing a cracked or worn actuator restores smooth operation and consistent switch engagement at the door dispenser.

• Engages the dispenser micro switch to initiate ice or water dispensing
• Provides the user-facing paddle/lever in the dispenser recess
• Helps the dispenser return to its rest position after you release
• Common symptoms: no dispense when pressed, intermittent response, broken/loose paddle, sticking or continuous dispense if jammed

• Unplug the refrigerator and shut off the water supply before servicing
• Carefully remove the dispenser trim/escutcheon to access the actuator; protect the finish and avoid breaking locking tabs
• Note spring and pivot orientation; transfer any reusable hardware to the new actuator
• Reassemble, restore power/water, and test both ice and water dispensing

This replacement cover restores a clean, finished look and protects the designated area of your appliance. Replacing a damaged or missing cover helps keep components shielded and secure so the unit functions and looks as intended. What it does:

• Shields and conceals the specific opening or component it's designed for
• Helps prevent debris and accidental contact with internal parts
• Restores proper fit and appearance when the original cover is cracked or missing
• Common signs it's needed: broken tabs, cracks, warping, or a cover that won't stay in place

• 1 cover

• Disconnect power before servicing
• Remove any retaining screws or release tabs; note orientation for reassembly
• Transfer and reuse original screws/clips if applicable
• Do not overtighten fasteners to avoid cracking the new cover

The refrigerator dispenser cover module is an OEM part for Frigidaire refrigerators. This grey module serves as an aesthetic cover that helps protect the dispenser mechanism. It is designed to blend in with the exterior of the refrigerator sheltering its internal components. 

Causes of a bad dispenser cover can include wear and tear over time, exposure to impacts or damage, or cracks that compromise its protective functionality. 

Symptoms of a bad dispenser cover include:

• Exposure of internal dispenser parts  
• Leaks around the dispenser area
• Loose or misaligned fit within the refrigerator
• Cracks or splits in the plastic material

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drip Tray is an OEM replacement part that fits Frigidaire refrigerators. It is responsible for catching water drips and spills under the water dispenser. Over time, the tray can crack or warp leading to leaks. Causes of failure include loss of the part, accidental damage, and wear over time. 

Symptoms of a failing drip tray include:

• water on the floor
• improper fit allowing leaks
• cracks or breaks in the tray

The drip tray is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, Crosley, and Kenmore refrigerator models

Kit includes ice and water actuator arms.

This ice dispenser lever is the actuator you press with your glass to release ice from the freezer door. A worn or broken lever can keep the door dispenser from dispensing ice or make it hard to activate.

• Transfers your push at the dispenser pad to the ice dispenser switch
• Helps restore normal ice dispensing from the door chute
• Common symptoms: lever broken, loose, or stuck; no ice dispensed when pressed
• May cause intermittent dispensing if the actuator is worn or misaligned

• Unplug refrigerator before service; wear cut-resistant gloves
• Remove dispenser trim and control panel as needed to access the lever
• Note spring and pivot orientation; transfer any reusable hardware
• Test dispenser operation before reinstalling trim

The Dispenser Module is an OEM part for Frigidaire refrigerators. It is an electronic component that controls the dispensing functions within the appliance's door or panel. This includes releasing filtered water, ice, and crushed ice on demand.

Causes of a bad dispenser module can include component malfunctions, circuit failures, or software glitches interrupting the dispensing process. 

Symptoms of an issue include:

• The dispenser not releasing any water, ice or crushed ice when tapped  
• Dispensing inconsistent amounts or none at all between uses
• Error codes shown related to the dispenser functions
• Operational noises from the dispenser that shouldn't occur

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Dispenser Module Cover is an OEM part for Frigidaire Refrigerator. It is the decorative plastic shroud that fits externally over the ice and water dispenser components.

Causes can be normal wear from frequent use of the dispenser, impacts from children or pets pressing on the area, or damage from attempted cleaning with improper chemicals over time.

Symptoms of a bad dispenser module cover include:

• Cracked, faded or stained external appearance
• Exposed wires and components vulnerable to liquid intrusion
• Cover not properly sitting flush or securely clipping into place

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This dispenser drip tray sits beneath the refrigerator's ice/water dispenser to catch drips and small spills, helping keep the area cleaner and reducing moisture on the door and surrounding surfaces.

• Collects water and ice drips under the dispenser
• Helps contain minor spills during dispensing
• Protects the door surface from moisture and staining
• Common signs of wear: cracked or missing tray, water pooling in the dispenser area, tray not sitting flush

• Disconnect power before working around the dispenser area
• Lift the old tray straight up and out of the recess
• Clean and dry the dispenser pocket to remove residue
• Align and press the new tray down until it sits flat and secure

The Frigidaire Refrigerator Water Filter Cover is an OEM part for Frigidaire refrigerators. It serves as a protective casing for the water filter, ensuring it is shielded from damage and securely in place within the appliance. This cover helps maintain the aesthetic integrity of the interior of your refrigerator while also providing easy access for filter changes.

Causes of a bad water filter cover can include physical damage such as cracks or breaks, which may occur from accidental impacts or during the filter replacement process.  

Symptoms of a bad Water Filter Cover include:

• Difficulty in accessing or replacing the water filter
• Loose fit that can lead to vibration or noise
• Visible damage like cracks or warping

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The refrigerator dispenser module overlay is an OEM part for Frigidaire refrigerators. This overlay sits atop the dispenser module providing additional protection and aesthetic appeal.

Symptoms of a bad dispenser overlay include:

• Cracks or breaks exposing underlying parts
• Misalignment or looseness within the refrigerator 
• Discoloration or wear affecting appearance
• Inability to fully or securely cover the dispenser module

Causes of a bad overlay can include damage from impact, repeated opening and closing of the refrigerator door, or general wear over time. 

This Frigidaire OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This dispenser drip tray sits at the base of the refrigerator's ice/water dispenser. It catches small drips and splashes to help keep the dispenser recess and door front cleaner and drier. What it does:

• Collects minor drips and splashes from the ice and water dispenser
• Helps protect the door finish and surrounding area from moisture
• Replace if the tray is cracked, warped, stained, or missing
• Common signs include water pooling in the dispenser recess or a loose, ill-fitting tray

• 1 dispenser drip tray

• Pull the old tray straight out of the dispenser recess; no tools are typically required
• Clean any mineral deposits or debris in the recess before installing the new tray
• Align and seat the new tray flat and flush in the opening
• Disconnect power and shut off water