General Electric Cooktop Parts

This igniter assembly creates the spark that lights a gas burner, helping restore quick, reliable ignition. Replacing a damaged or shorted igniter can address burners that won't light, intermittent ignition, or repeated clicking without flame.

• Generates a high-voltage spark at the burner to ignite gas
• Ceramic-insulated electrode focuses the spark for consistent lighting
• Failure can cause no spark at a specific burner, delayed ignition, or constant clicking
• Visible cracks, carbon tracking, or damaged lead are common replacement indicators

• Disconnect power and shut off gas before servicing
• Allow the appliance to cool; handle the ceramic insulator carefully to avoid breakage
• Route the lead away from heat and moisture; secure connections firmly
• Align the electrode tip correctly with the burner for reliable ignition

This 6-inch surface element restores steady, even heat to the small burner on your electric range. Replace a burned-out coil to get back to reliable boiling, simmering, and everyday cooking performance.

• Converts electrical power into heat at the 6-inch burner position
• Helps when the small surface burner won't heat or heats unevenly
• Common signs include visible hot spots, blistering, or burned/loose terminals
• Seats in the drip bowl and connects to the proper surface element receptacle

• Disconnect power at the breaker or unplug the range; allow the element to cool before servicing
• Lift the old element from the drip bowl and pull straight out from the receptacle; avoid twisting or bending the coil
• Inspect the element receptacle for heat damage; replace the receptacle if contacts are burned or loose
• Fully seat the new element and ensure it sits level in the drip bowl before use

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

This switch mounts on the surface burner gas valve stem and closes the circuit to the spark igniters when you turn the knob. Replace a worn switch to restore reliable ignition and eliminate nuisance or no-click conditions.

• Activates the spark module for the selected burner when the knob is turned
• Common symptoms: no spark/click on that burner, intermittent lighting, or continuous clicking after flame is lit
• Helps correct single-burner ignition issues caused by a failed valve switch
• Typical wear item from use, heat, or moisture exposure around the cooktop

• Disconnect power and shut off gas before servicing
• Remove the burner knob and access the valve/switch at the manifold
• Note wire positions and transfer one at a time to the new switch
• Ensure the switch seats on the valve stem and test for proper spark before reassembly

This is a medium burner bowl, also sometimes known as a drip pan, and it is made for ranges, stoves, and cooktops. This is a genuine replacement part made by General Electric. The burner bowl is situated underneath the heating element and is able to catch any food or debris that falls when cooking. The bowl or drop pan is there to catch any and all waste so that the user may easily clean up after the heat is turned off and the appliance is cooled down.A new medium burner bowl might be needed if the current one is damaged in any way including being broken or bent so that is it not fully secure under the burner. This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with ranges, stoves, or cooktops made by General Electric.

Includes 12 washers.

This part is the lens for a small appliance light on select GE cooking products. It covers and diffuses the lamp, protecting the opening and restoring a clean, finished appearance so status illumination is easy to see.

• Covers and diffuses a panel/indicator light so it's visible without glare
• Helps shield the lamp cavity from grease, moisture, and debris
• Restores proper appearance if the original lens is cracked, missing, or discolored
• Common symptoms: missing or broken lens, cloudy/yellowed lens, exposed indicator lamp

• Disconnect power to the appliance before servicing
• Access the lens from the rear of the panel or mounting area; release retaining tabs or hardware
• Seat the new lens fully and align any tabs before securing
• Restore power and verify the indicator light shines through clearly

This indicator light cover is the protective lens for the status light on a range or cooktop. It shields the opening and diffuses the light so on/hot indications stay visible while helping keep dust and moisture out.

• Protects the indicator opening and retains the light assembly in the control panel
• Diffuses the light for clear on/hot visibility
• Restores a finished look and helps keep debris and moisture out of the panel
• Replace if the lens is cracked, discolored, loose, or missing

• Disconnect power to the appliance before servicing
• Access the control panel, release the old cover's retaining tabs, and remove
• Seat the new cover fully so tabs engage; transfer any clip/gasket from the original if present
• Restore power and verify the indicator light is clearly visible and the cover is secure

Color: Black. Small

This 8-inch surface burner element is the plug-in coil used on many electric ranges. Replacing a worn or failed element restores reliable heating and more even cooking performance on your stovetop.

• Provides heat to pots and pans when energized by the surface control
• Common fix for an element that won't heat or only heats partially
• Addresses visible coil damage such as breaks, blisters, or burned spots
• Corrects intermittent heating caused by an open or failing element

• Disconnect power to the range/unplug before servicing and ensure the element is cool
• Lift the old coil slightly, then pull straight out from the receptacle
• Inspect the receptacle/terminal block and drip bowl; replace if overheated or damaged
• Fully insert the new element terminals into the receptacle, seat the coil level, and test

This chamfered nut is a genuine fastener used to secure mating parts inside your appliance. It replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and proper alignment.

• Provides threaded clamping force to fasten components
• Helps maintain alignment and resist loosening from vibration and heat cycles
• Replaces rounded, stripped, corroded, or missing nut
• Typical symptoms: loose panels/brackets, rattling noises, or parts shifting out of place

• Disconnect electrical power; turn off gas supply before servicing
• Allow the appliance to cool completely; wear gloves and eye protection
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Match orientation/position to the original

Refresh your cooktop with this white burner drip bowl. It sits beneath a surface coil element to catch spills and splatters, reflect heat toward cookware, and help the element seat correctly for consistent performance and easier cleanup.

• Supports and centers the surface coil element
• Collects drips to protect the cooktop surface
• Reflects heat to aid efficient burner performance
• Restores appearance when the original bowl is stained, rusted, or warped

• Disconnect power to the range before servicing.
• Pull the surface coil straight out of the receptacle to remove it.
• Lift out the old bowl; align the locator notch on the new bowl and seat it flat.
• Reinsert the element fully and verify proper operation before restoring power.

The Burner Grate is an OEM part for GE gas ranges. This component supports cookware above the burner, allowing for even heating and stable placement of pots and pans during cooking. 

Causes of a bad burner grate can include prolonged exposure to high heat, accidental dropping or impact, or wear and tear from frequent use. A damaged grate can affect cooking efficiency and safety by causing instability for cookware.

Symptoms of a bad burner grate include:

• Cracks or chips in the grate
• Uneven or unstable cooking surface
• Rust or discoloration
• Difficulty in placing pots and pans securely

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dual radiant surface element sits beneath the glass cooktop and provides two heating zones to match your pan size. Replacing a failed element restores fast, even heating and proper control on the affected burner.

• Heats cookware via two concentric radiant circuits beneath the glass-ceramic surface
• Lets you select inner, outer, or both rings for small or large pans (via the burner control)
• Cycles with its internal limiter to maintain the temperature you set
• Common symptoms: no heat, only one ring heats, uneven or slow heating

• Disconnect power at the breaker before servicing
• Lift/remove the glass cooktop to access elements; support the glass to prevent stress or cracks
• Transfer wiring and any mounting brackets from the old element to the new one, moving one connection at a time and documenting positions
• Test the burner for proper operation before reassembly

The Knob is an OEM part for GE ranges and cooktops, designed to allow users to control the heat output of the stove's burners. This knob is a direct replacement for the original equipment, ensuring a perfect fit and proper function. It is typically made of durable materials to withstand the heat and frequent use associated with cooking.  

Over time, burner knobs can become worn or damaged due to heat exposure, cleaning chemicals, or accidental impacts. This wear can lead to difficulty in accurately setting the burner temperature or, in some cases, the knob may become loose or break off entirely.

Symptoms of a bad Burner Knob include:

• Difficulty in turning the knob or a lack of resistance 
• Faded or missing indicator markings 
• The knob no longer aligns correctly with the burner's settings 

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This six-point spark ignition module for gas cooktops/ranges converts line voltage into high-voltage pulses that fire the burner igniters. It restores consistent, reliable lighting across multiple burners when you turn a knob.

• Distributes high-voltage pulses to up to six surface-burner igniters when a burner switch is turned on
• Helps resolve no spark/click on all burners, no spark on some burners, intermittent ignition, or continuous clicking
• Replaces a module that produces weak, erratic, or no spark
• Ignition control only; it does not regulate gas flow or flame size

• Disconnect power and shut off gas before servicing
• Photograph and label all wires; transfer them one at a time to the matching terminals (six HV outputs plus power/ground)
• Mount securely in the original location and keep connections dry; after installation, ensure burner caps are seated and igniters are clean