General Electric Cooktop Parts

This spark module controls surface-burner ignition on gas cooktops and ranges, sending high-voltage pulses to the igniters when you turn a knob. Replacing a failed module restores quick, consistent sparking so burners light reliably.

• Generates and routes high-voltage pulses to the surface burner igniters
• Triggers sparking when a burner knob is turned to the Ignite/Light position
• Common symptoms: no spark or clicking on any burners; multiple burners won't ignite; weak or intermittent sparking
• Restores dependable ignition performance across the surface burners

• Disconnect electrical power and shut off gas supply before servicing
• Access the module behind the control area or beneath the cooktop, depending on model
• Label and transfer wires one at a time to the new module to maintain correct placement
• Mount securely and ensure a good ground; test burner ignition before reassembly

This LP orifice spud meters gas to a range burner when using liquid propane. Replacing a worn or incorrect jet helps restore proper flame size and clean combustion during LP setup or conversion.

• Meters LP gas to the burner for correct flame height and color
• Helps resolve large yellow flames, soot, and poor simmering caused by an incorrect/blocked spud
• Supports safe operation when converting from natural gas to LP per the manufacturer's instructions
• Can improve ignition and flame stability when the original jet is damaged or clogged

• Disconnect power and shut off the gas supply; allow the appliance to cool before servicing
• Remove the existing spud with the correct wrench and install the replacement snugly—do not overtighten
• Perform any required air-shutter/burner adjustments per the service instructions
• After installation, leak-check with a soapy water solution; LP conversions should comply with local codes

Medium. Color: Grey. It measures about 3 inches in diameter.

Large. Color: Grey. It measures about 3-1/2 inches in diameter.

This switch harness assembly links the cooktop burner knob switches to the ignition circuit so the burners spark when you turn a knob. Replacing a damaged harness restores consistent lighting and can stop intermittent or continuous clicking during use.

• Routes electrical signals from the surface burner switches to the spark module
• Triggers igniters to click when a knob is turned to Lite
• Typical symptoms: no spark on any burner, constant clicking, or sporadic ignition
• Physical clues: heat-damaged insulation, broken connectors, or moisture intrusion

• Disconnect electrical power and shut off gas before servicing.
• Access location varies by model; remove knobs and lift the cooktop or front panel to reach the harness.
• Label or photograph wire routing; transfer connectors one at a time to avoid miswiring.
• Route wires away from sharp edges and hot surfaces; reassemble, restore power, and test each burner.

This relay board works with the main control to switch power to high-load oven components. Replacing a failing board can restore consistent heating and reliable performance across bake, broil, and convection functions. What it does:

• Switches high-voltage power to oven elements and fans as directed by the control
• Loss of heat in one or more modes (bake/broil/convection) is a common failure symptom
• Intermittent or erratic heating, long preheat, or heat stopping mid-cycle
• Visible burn marks or heat damage on the board

• Disconnect power at the breaker or fuse box before servicing
• Access location varies by model (rear panel or control compartment)
• Photograph wiring and move connectors one at a time to the new board
• Handle by the edges and use anti-static precautions; reuse existing hardware

Color: black. Measures about 2 inches in diameter.

1200W Element Control

Ranges and ovens have grate feet installed on the underside of their cooktop grates. This rubber piece keeps the stovetop from getting scratched by the grate when there is pressure applied. With use, misplacement, or other damages, there is a requirement for one more replacement grate foot pieces.A stovetop with scratches on the surface indicates a missing grate foot. There are four grate foot parts on each grate. The replacement of a grate foot is a simple process. Remove the grate covering the area where a visual inspection has determined there is a missing foot grate. Clean the area thoroughly. Apply the new foot grate. Reposition the grate on the stovetop. Wear gloves for safety. It's recommended to unplug the appliance while doing the replacement to prevent accidental activation of the cooktop.This grate foot is an authentic OEM replacement part. It is sold as an individual unit. It is made of high-quality, durable rubber. The piece is sourced directly from the manufacturer. It is compatible with several models of ranges and cooktops. The grate foot fits in appliances produced by General Electric, RCA, and Hotpoint.

H Burner

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

• 1 hold-down bracket

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

This 9-inch dual radiant surface element kit replaces a failed burner on a smooth-top electric range or cooktop, restoring dependable, even heating and letting you choose a smaller or larger heating area to match your cookware.

• Provides two selectable heating zones (inner and outer rings) to match pot size
• Heats cookware evenly across the chosen zone on glass-ceramic cooktops
• Typical symptoms include no heat, only one ring working, slow or uneven heating, or intermittent operation
• Restores burner performance after internal failure of the element assembly

• Disconnect power at the circuit breaker before servicing; 240V shock risk
• Allow the cooktop to cool completely; protect the glass surface while working
• Photograph wiring and transfer leads one at a time to matching terminals on the new element
• Ensure the element seats correctly in its support brackets; test both inner and outer rings before final reassembly

This bracket secures the cooktop/main top to the appliance chassis to keep the surface stable and properly aligned. Replacing a bent or missing bracket can eliminate looseness, rattles, and visible gaps so the top seats correctly.

• Anchors the cooktop/main top to the frame
• Maintains proper spacing and alignment of the top
• Helps prevent vibration and movement during use and cleaning
• A damaged or missing bracket can cause a loose, uneven, or rattling cooktop

• Disconnect power and, for gas units, shut off the gas supply before servicing
• Access the bracket location per your model's service procedure (top may need to be lifted or removed)
• Transfer and reuse mounting screws/clips from the original bracket if required
• Install in the same orientation, check alignment, and tighten fasteners securely before restoring service

This is a burner head, and it is intended for use ranges or stove top ovens. This is a genuine replacement part made by General Electric. Burner heads are used on the top of stoves or ranges to provide heat.A new burner head might be needed if the current one is unable to turn on or off. Another way to determine if a new burner head is needed is if the knobs indicate the burner should be putting off heat but the burner head does not feel hot to the touch. Be sure the current burner head is fully connected before determining whether a new one is needed.This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with ranges or stoves made by General Electric.

Liquid propane. Simmer burner

This economic nut is a small replacement fastening nut that restores secure connections for appliance components. It replaces worn or missing hardware so panels and internal parts stay firmly seated and reduce vibration. What it does:

• Secures components and panels by threading onto the matching stud or bolt to hold assemblies in place
• Prevents loose or rattling panels and hardware caused by a missing or damaged nut
• Restores proper fit for user-accessible panels and internal brackets where this nut is specified
• Simple hardware replacement to regain stable mechanical connections

• Disconnect power and water (if applicable) and follow basic electrical safety before servicing the appliance
• Use the matching size wrench or socket; thread-on by hand first to avoid cross-threading, then snug—do not overtighten
• Inspect mating stud or bolt for damage; replace hardware that is stripped, corroded, or deformed