General Electric Range / Cooktop / Oven Parts

White front control panel for your range console. Restores clean appearance and secure mounting for controls. Replace if cracked, broken, or worn.

Secures the cooktop surface to the range chassis for stable alignment. Replace if bracket is bent, broken, or missing to eliminate looseness and gaps.

Seals the gap between your oven door and frame to maintain accurate temperatures. Replace when worn to restore proper heating and prevent heat loss.

White plastic end cap for the right side of your range. Replaces old, yellowed, cracked, or broken trim pieces. Restores a clean appearance.

Replacement oven door handle for ranges. Restores secure grip and finished appearance when original handle is cracked, broken, or missing. Installs on door.

Approx 3 inches in diameter

The Terminal Block is an OEM part for GE electric ranges. It serves as a critical junction point where the range's wiring connects to the heating elements, ensuring proper electrical flow and operation of the oven and cooktop. This component is essential for the safe and efficient functioning of your appliance.

Causes of a bad terminal block can include overheating due to electrical surges, corrosion from prolonged exposure to heat and moisture, or physical damage from improper installation or handling.

Symptoms of a bad terminal block include:

• The oven or burners not heating properly
• Visible signs of burn marks or corrosion on the block
• Electrical arcing or sparking
• Intermittent or no power to the heating elements

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

If your oven won't heat or displays error codes, the relay board may have failed. This assembly routes power to burners and heating elements.

Fix an oven that won't reach set temperature or has an indicator light that stays on. This thermostat regulates heat by cycling elements for accurate baking.

Burner won't ignite, flame won't adjust, or gas leaks? This top burner valve controls gas flow to your range's surface burners. Moderate DIY repair.

This plunger switch is the push-style electrical switch that completes a circuit when an actuator is depressed, restoring reliable on/off signaling. Use it to replace a worn or broken plunger switch that causes intermittent or non-responsive operation. What it does:

• Closes an electrical circuit when the plunger is pushed, sending a signal to the appliance control.
• Commonly used where a door, lever or dispenser actuator must register a position or user input.
• Can correct symptoms like intermittent operation, a dispenser or mechanism that won't activate, or a stuck/unresponsive actuator.
• Acts as a direct mechanical-to-electrical interface—no electronics required.

• Disconnect power (unplug or turn off breaker) before servicing to avoid shock.
• Remove the access panel or housing to reach the switch; note actuator orientation before removal.
• Disconnect terminals or harness, then swap the old switch for the new one; reconnect terminals securely.
• Test the plunger action and appliance function before reinstalling panels.

This 9-inch dual radiant surface element kit replaces a failed burner on a smooth-top electric range or cooktop, restoring dependable, even heating and letting you choose a smaller or larger heating area to match your cookware.

• Provides two selectable heating zones (inner and outer rings) to match pot size
• Heats cookware evenly across the chosen zone on glass-ceramic cooktops
• Typical symptoms include no heat, only one ring working, slow or uneven heating, or intermittent operation
• Restores burner performance after internal failure of the element assembly

• Disconnect power at the circuit breaker before servicing; 240V shock risk
• Allow the cooktop to cool completely; protect the glass surface while working
• Photograph wiring and transfer leads one at a time to matching terminals on the new element
• Ensure the element seats correctly in its support brackets; test both inner and outer rings before final reassembly

This is a genuine OEM replacement grease filter for use on cooktops. The air filter is used during cooking to filter smoke, grease, and other air contaminants from the air. When food is overheated, and smoke fills the kitchen, the air filter will pull the smoke from the air through the filter and out the exhaust. This helps to keep the air in the house odor and smoke-free. Odors can alter the way food tastes, so keeping the air and grease filter changed can help when serving food and how it is received. This filter also catches grease particles when cooking food in oil. These spatters will eventually clog the filter and necessitate the need to remove and replace it. If the filter is not removed, the air will not be able to circulate through it, and the filter will not work efficiently. Removal does not require tools. The filter is simply pulled out of the cavity and a new one placed in the cavity. The old filter should be discarded; this is not a filter that can be washed and reused. This filter is a black metal part that is sold individually. It is designed for stovetops and ranges manufactured by General Electric.

White plastic end cap that installs on the left side of your range control panel. Replaces cracked, yellowed, broken, or missing trim pieces.

This replacement range handle restores a secure, easy-to-grip handle for ranges that use part WB15X10225. It returns normal door operation and improves safety and usability for ovens with a damaged or missing handle. What it does:

• Replaces a cracked, broken or loose range/oven door handle.
• Provides a stable gripping surface for opening and closing the oven door.
• Stops handle wobble and prevents accidental detachment during use.
• Matches the factory-style fit and function for straightforward replacement.

• Disconnect power to the appliance before beginning any repair.
• Follow the range/oven manufacturer's door-removal and reassembly instructions when required.
• Basic hand tools are typically required; handle screws fasten securely to the door.

Replacement double burner assembly for gas range cooktops. Installs under the main top to route gas to two burner outlets. Replace if damaged or worn.