General Electric Range / Cooktop / Oven Parts

The Knob is an OEM part for GE appliances designed for use with various stove and oven models. This knob allows users to control the settings of their appliance, whether adjusting the temperature of the oven or setting the heat level on the stove. 

Symptoms of a bad knob include:

• Difficulty turning or adjusting the settings
• Knob slipping or failing to engage with the control mechanism
•  Cracks or breakage that prevent proper function

Causes of knob deterioration often include mechanical stress from frequent use, exposure to heat, or damage from cleaning products or impacts.

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This thermostat control knob replaces a worn or missing oven temperature selector. It attaches to the thermostat shaft so you can set the oven temperature again with a solid, positive feel and clear pointer alignment.

• Mounts on the thermostat shaft to select and adjust oven temperature settings
• Restores grip and control when the original knob is cracked, stripped, loose, or missing
• Helps ensure the control turns smoothly and the pointer lines up with the dial markings
• Freshens the appearance of the control panel

• Disconnect power and shut off gas supply before servicing
• Pull the old knob straight off; avoid bending the control shaft
• Align the flat/D-shaped opening with the shaft and press on firmly until fully seated
• Rotate through the full range to ensure smooth operation

Color: White. This is the right side end cap. For left side use WB07K10007.

Oven doors utilize door hinges to open and close efficiently. There is a door hinge attached to opposite ends of the door, and the part is also connected to the range. With time, the hinges can wear out, get damaged, or break off. When the hinges are no longer functioning correctly, replacement parts are necessary to continue using the appliance.An indication that there is a problem with the door hinge on an oven door is difficulty opening or closing or a door that partially slips on one side or the other out of position. A visual inspection will determine the condition of a door hinge. The replacement of the piece is simple. Unplug the range from its power source before starting the repair. Wear gloves for protection. Check the condition of both hinges before ordering. This door hinge is an authentic OEM replacement part. It is sourced directly from the manufacturer. The piece is sold as an individual unit. The door hinge fits several different models of ranges. The replacement part is compatible with appliances produced by General Electric, Hotpoint, and RCA. It is manufactured using high-quality, durable metal materials.

1900W Element Control

Restore safe, reliable heating with this bimetal limit switch. It senses excessive temperature inside your range or cooktop and opens the circuit to prevent overheating, then automatically resets once the area cools to a safe level.

• Monitors temperature and interrupts power when a preset limit is reached
• Automatically resets after cooling to resume normal operation
• Helps protect heating components, wiring, and controls from heat damage
• Common signs of failure: little or no heat, intermittent cycling, or overheating; fails continuity testing

• Disconnect power and allow the appliance to cool completely before servicing
• Access the switch location; note wire positions and transfer them one at a time to the new switch
• Mount the new switch in the same orientation; ensure proper thermal contact as designed
• Inspect connectors for heat damage, replace if needed, then reassemble and test operation

This glass touch assembly is the stainless front user-interface panel for the oven controls. It replaces a worn, cracked, or unresponsive touch keypad so you can select modes and temperatures and operate your appliance reliably.

• Provides the touch-sensitive keys for cooking modes, temperature, timer, and light functions
• Sends user inputs to the electronic control; failure can prevent starting or adjusting the oven
• Common symptoms: some keys don't respond, random beeping or key error codes, unable to set temperature
• Restores appearance when the front control glass is scratched or cracked

• Disconnect power at the breaker before servicing
• Support the panel and handle glass carefully; remove trim and mounting screws
• Move ribbon/plug connectors one at a time to the new assembly; avoid creasing flex cables
• Reinstall hardware and test all touch keys before final reassembly

This 250V 15A safety fuse protects the appliance's line circuit from overcurrent. When the original fuse has blown, replacing it can restore power and help safeguard internal components from further damage.

• Opens the circuit if excessive current or a short occurs, protecting internal parts
• Common symptom: unit completely dead—no display, lights, or response to controls
• Blown fuse will test open (no continuity) with a multimeter
• If a new fuse blows again, another component may be shorted and needs diagnosis

• Unplug the appliance before servicing; microwaves can retain a dangerous charge—discharge the high-voltage capacitor
• Access the fuse near the line filter/control area; note clip orientation
• Replace only with the same 250V 15A rating; never bypass or upsize the fuse
• If the replacement fuse blows immediately, stop and troubleshoot the root cause

Liquid propane. Main burner.

Radiant Surface Element 4400 Watts

This burner grates provide a stable surface on which to balance cookware and keep it squarely over the top of the flame on a gas range. This particular set includes all of the grates required to cover the burners on compatible range models. Over time, burner grates might become worn, dented, bent, corroded, or simply too damaged or dirty to use. No tools are needed to replace this part. Remove the old grates and slot the new ones into place. This part is a genuine OEM replacement burner grate set intended for use with gas range models. This part has been made by General Electric and has been sourced directly from the manufacturer. This part is made out of high-quality, durable, non-corrosive metal to ensure durability. This burner grate set is sold individually. It is intended for use with gas ranges manufactured by General Electric, Hotpoint, RCA, and other brands.

This drawer wedge aligns and stabilizes the lower drawer so it opens and closes smoothly and sits flush. Replacing a worn or missing wedge helps eliminate wobble, rubbing, and gaps for better everyday operation.

• Supports and centers the drawer for proper alignment on the slides
• Acts as a spacer/stop to reduce vibration and metal-to-metal contact
• Helps prevent binding and keeps the drawer from popping off the track
• Common symptoms: drawer crooked or sagging, won't close fully, rattles, or feels loose

• Disconnect power and allow the appliance to cool before servicing
• Pull the drawer out to the stops, release the side track tabs, and remove the drawer
• Note the original wedge's position; remove it and install the new wedge in the same orientation (reuse existing hardware if applicable)
• Reinstall the drawer on the rails and verify smooth operation and proper fit

Restore a cracked, shattered, or stained oven door panel with this bisque-finish glass. Replacing the damaged glass refreshes your range's appearance and helps the door assembly contain heat as designed.

• Forms part of the oven door assembly to help retain heat inside the cavity
• Replaces broken, chipped, or discolored glass panels
• Addresses cosmetic damage that can make the appliance look worn
• Color-matched bisque finish for compatible models

• Disconnect power and, for gas ranges, shut off gas; allow the oven to cool completely
• Wear cut-resistant gloves and eye protection; handle glass carefully and support the door
• Remove the door per your model's instructions and work on a padded surface
• Transfer any model-specific trim/handle as required; tighten fasteners evenly without overtightening

Color: Black. Measures about 2 inches in diameter.

This thermostat knob assembly is the user control that fits onto the temperature selector shaft. It lets you set and read temperatures and restores secure operation when the original knob is cracked, stripped, loose, or missing.

• Fits onto the thermostat/control shaft to select temperature settings
• Provides a firm grip and clear pointer alignment for accurate selection
• Common fix for knobs that are cracked, worn, melted, missing, or won't stay on
• Replacement is recommended

• Disconnect power and allow the appliance to cool before servicing
• Pull the old knob straight off the metal control shaft—do not bend the shaft
• Align the flat/D-shaped opening and indicator, then press the new knob fully onto the shaft
• Smooth operation through the full range of settings

Restore smooth temperature selection with this oven thermostat knob. It mounts on the thermostat shaft to let you choose the oven setting on models that use a mechanical thermostat, replacing cracked, stripped, or missing knobs.

• Turns the oven thermostat to set the desired temperature
• Replaces knobs that are cracked, stripped, loose, or missing
• Restores proper grip and engagement with the thermostat shaft
• Replacement is recommended if the knob won't stay on or is hard to turn

• Disconnect power; for gas ranges, also shut off the gas supply
• Pull the old knob straight off the thermostat shaft
• Align the new knob with the shaft orientation and press on fully—do not force
• Avoid bending or twisting the thermostat shaft during installation