General Electric Range / Cooktop / Oven Switch

Range burner not heating or stuck on high? This infinite switch controls power flow to surface elements. Direct replacement restores proper heat control.

Burner not heating or stuck on one temperature? This infinite switch restores variable heat control to your electric cooktop element. Moderate DIY repair.

This rotary switch replaces a worn or failed control selector to restore reliable function selection. It provides a direct, mechanical interface for choosing settings so controls respond properly when the knob is turned. What it does:

• Routes user input from the control knob to the appliance's control circuits
• Restores reliable selection when a knob won't change settings or clicks without engaging
• Stops intermittent or no-response behavior caused by worn switch contacts
• Supports normal operation of the affected control bank or function

• Disconnect power (unplug or switch off breaker) before starting any work
• Label or photograph wiring before removal to ensure correct reconnection
• Access may require removing a control panel or trim; keep fasteners and small parts organized
• After installation, restore power and verify all functions operate as expected

Burner won't heat properly or stuck at one temperature? This infinite switch restores variable heat control to your cooktop elements. Direct replacement.

Oven won't start or displays error messages? A faulty door latch switch prevents operation when the door signal fails. Direct replacement restores safety.

If your cooktop burner won't ignite or sparks continuously, the igniter switch may be faulty. This switch controls spark ignition for safe lighting.

This burner box wiring harness connects the cooktop/oven burner components to the appliance's control systems, restoring reliable ignition and power routing for the burner box area. Use to replace a damaged or burnt harness for safer operation. What it does

• Routes electrical connections between igniters, sensors, switches, and control modules in the burner box
• Restores ignition or heating when a frayed or open harness prevents burners from sparking or heating
• Replaces harnesses with cracked insulation or melted connectors that can cause intermittent operation or arcing
• Helps eliminate electrical shorts and poor contact at connector plugs inside the burner box

• One burner box wiring harness as shown

• Disconnect all power (electrical and gas) before servicing; verify power is off
• Inspect connectors and routing in the burner box, replacing any mounting clips or fasteners if damaged
• Ensure correct connector seating and secure wiring away from high-heat components

Burner won't change heat settings or stays on one temperature? This infinite switch restores adjustable control to your range's surface elements.

This fan relay is an electrical replacement part that restores the relay control for the refrigerator/freezer fan motor so the appliance can circulate air properly and maintain even cooling. Use it to replace a failed relay and return fan operation. What it does:

• Switches electrical power to the evaporator/condenser fan motor when the control calls for airflow
• Commonly used when the fan won't start, runs intermittently, or the appliance struggles to maintain temperature
• Helps stop clicking or repeated start attempts caused by a bad relay
• Works as the control interface between the main control and the fan motor

• One fan relay

• Always unplug the appliance before starting any repair to avoid shock risk
• Locate the relay on the compressor or control module per your model's service guide and note connector positions before removal
• Transfer wiring/plug connectors exactly; avoid bending pins or over-tightening fasteners

Replace a faulty range igniter switch when burners won't light or spark inconsistently. This switch controls the spark ignition system for gas burners.

Burner stuck on high or won't adjust temperature? This infinite switch restores adjustable heat control to your surface burner. 10-minute repair.

Fixes burner that won't heat or adjust temperature properly. This 6-inch surface element switch restores precise heat control to your electric range cooktop.

This compressor start relay helps the refrigerator compressor receive the initial jolt it needs to start running, restoring normal cooling when a worn relay prevents compressor startup. It's a direct-fit replacement specified by the manufacturer. What it does:

• Provides the momentary boost the compressor needs to start under load
• Helps prevent repeated hard-start attempts that can overheat or damage the compressor
• Commonly used when a refrigerator hums but the compressor won't start
• Works with the compressor's start device circuitry to control start winding engagement

• One replacement compressor start relay

• Disconnect power to the appliance before servicing to avoid shock
• Access and replace the relay per the appliance's service instructions; avoid bending terminals
• Inspect the compressor and wiring for additional damage before reassembly

If your upper oven won't switch cooking modes or heat settings, the selector switch likely failed. This direct-fit control panel switch restores mode selection.