General Electric Range Parts

Purchased new end brackets. Then installed them very easily by taking out 6 screws. Read more

Easy fix. Both elements replaced while I was at it, so all new. Figured if one went the other was going to follow. CIRCUIT BREAKER OFF. Removed the back metal panel with my nut driver for the hex head screws. Note where the panel may slip under tabs for support. Remove slip on electrical connections on upper and lower elements. May need a pliers. (I did not want to just pull the element and the wires into the oven with the element and remove them there, like a technician would do. After 15... Read more

I first checked a repair video and found the procedure was a 10 minute job. I then went to the website, put in my stove model number and searched for the switch. While I was looking I was offered a chat session with one of their experts. I am glad that I accepted. The switch I was looking at was not the right switch for the job. My expert verified my model number and the switch that need to be replaced. After a couple of minutes, she came back with the right part and placed the order for... Read more

Fixed it by replacing Valve Control Assemble and Range Oven Igniter, a little intimidating at first,but the videos from Appliance Parts Pro made so much easier.Whenever I need parts for appliance in the future AppliancePartsPros will be my first choice. Read more

Ordering the right part is the key. This is the element with 3 wire connectors NOT the usual kind with 2 prongs that slide in. Thank goodness this company carries these elements for old GE built-in stoves. I'm not super handy but replaced two in about 40 min. Make sure you save the old ceramic clamps. The three prongs of the element with connected wires need to fit completely in the ceramic grooves so the two sides can be clamped together. The new element comes with everything you need but... Read more

Got the window and replaced it no time Read more

Found and ordered the handle on appliance parts pros. It was easy to find came in earlier than expected. The handle was easy to install and fit perfectly Read more

The video shown was completely incorrect for the gasket needed on my range. I had to remove the door, disassemble the inside panel, and remove the old gasket. I suggest you have assistance when doing this. Putting on the new gasket was challenging but not impossible for a do it your selfer. You should make a video for this gasket so people don't think it is as easy as pulling a few pins around the window!! Read more

Was able to get part number and ordered online. Was an easy fix! New knob looks a little new now but that should change! Read more

Removed the defective burner labeled the leads as to their location and coil connections. Replaced the connections to the corresponding locations, 1 to 1, 2 to 2 and the bridged terminal as it was. I noticed that the coils in the replacement burner were not wound in the same direction as the original burner and made note of this. I did not think much of this at the time, but on turning the power back on and lighting up the burners I noticed up they were not lighting up the corresponding... Read more

Put in new glass Read more

Ordered new light bulb Read more

I always save original books and assembly sheets for appliances. That helped a lot ! The assembly sheets showed how the ovens went in, how they were attached to the cabinet and what to avoid so I didn’t bend trim piece. Original booklet showed how to replace oven doors and lights etc. Once the hinge assemblies arrived I started replacement after having read on the internet original hinges had some problems. So I had ordered both right and left hinges to avoid a possible problem with the... Read more

Took top apart to find out that the problem was just the lens for the light was broken. Come to find out that the lens is what holds the light in place. When the lens broke the light fell down into the base of the cooktop. I bought a light and lens but for the price I could not go wrong. I cannot believe how fast and easy my order was handled!! Awesome company Read more

• Timer will not advance

Replaced above parts, easy to do, looks like a new stove. Needed to pry open knob stem slot segments very slightly to remove broken plastic from previous knobs. Spreading stem slot metal sides too much and they will break. With slots cleaned out, pinch stem sides almost together for new knobs to slide on. Customer service rep was helpful and parts delivery was next day as promised. Before contacting Appliance Parts Pros, I found their on-line customer reviews were much better than their... Read more

Very easy replaced switch. Read more