General Electric Refrigerator Gasket & Seal

This self-adhesive foam strip provides a flexible seal and buffer for appliance gaps, helping reduce drafts, rattling, and moisture intrusion. Designed for easy stick-on replacement where foam padding or sealing is needed. What it does

• Seals small gaps between components to help reduce air leaks and temperature loss
• Cushions panels and doors to minimize noise and vibration
• Helps block moisture and dust from entering sensitive areas
• Self-adhesive backing allows for quick placement without extra glue

• One self-adhesive foam strip

• Surface must be clean and dry; wipe with isopropyl alcohol for best adhesion
• Measure and trim the foam strip to fit—use scissors or a utility knife
• Press firmly along the length to ensure full contact; allow adhesive to set before closing doors or panels
• For safety, disconnect power to the appliance before working in internal areas

This front pan seal replaces the worn gasket that seals the refrigerator's front drip/pantry pan, helping keep water contained and directing drainage properly to prevent puddling and odors. Fits the pan edge at the fridge base. What it does

• Creates a tight edge seal along the front of the refrigerator drain/drip pan to keep condensation and defrost water contained.
• Helps direct water toward the drain channel so it can evaporate or flow to the condenser pan.
• Reduces chance of water pooling on the floor near the refrigerator base.
• Can improve odor control by preventing trapped moisture under the pan.

• One front pan seal.

• High-level swap: remove lower kickplate (if present), peel out the old seal and press the new seal into the pan groove; follow OEM instructions for your model.
• Use gentle, even pressure to seat the seal fully into the pan channel; avoid stretching the seal excessively.
• If adhesive is used by the model, only apply OEM-recommended adhesive in small amounts.
• Disconnect power or follow safety steps before working near electrical components.

This evaporator block seal replaces the rubber gasket that seals the evaporator block assembly to the freezer cabinet, helping maintain proper airflow and prevent leakage. It restores a tight seal around the evaporator block for reliable cooling performance. What it does:

• Seals the evaporator block to the cabinet to prevent warm air intrusion and water leaks
• Helps direct refrigerant-condensed water into the drain rather than inside the cabinet
• Commonly used when you see frost build-up around the evaporator or water pooling in the freezer
• Helps maintain consistent cold temperatures by preserving the sealed evaporator area

• One evaporator block seal

• Designed for field replacement; inspect surrounding gaskets and mounting surfaces for damage before installing
• Clean and dry mating surfaces thoroughly to ensure a proper seal
• Use common hand tools; avoid over-stretching or cutting the seal during installation
• Disconnect power to the appliance before servicing and follow safety precautions for refrigeration components

A self-adhesive foam strip that cushions gaps and seals edges to reduce air leaks, vibration, and moisture intrusion. Simple peel-and-stick design makes it a fast way to restore proper sealing and quiet operation. What it does

• Creates a soft seal along doors, panels or trim to help stop cold air loss and drafts.
• Dampens vibration and rattles caused by loose or worn mounting surfaces.
• Helps block dust and moisture from entering seams and crevices.
• Works where a thin, compressible filler is needed for a snug fit.

• Clean and dry the mounting surface thoroughly before installation for best adhesion.
• Measure and trim foam to fit; peel backing and press firmly to adhere along the entire length.
• Avoid stretching the foam during installation; allow adhesive to set before regular use.
• If adhesive residue remains on hands or surfaces, use a mild solvent per manufacturer guidance.

This Seal QC Damper is the gasket that seals the refrigerator/freezer air damper to help maintain proper airflow and temperature control. It replaces a worn or damaged seal to reduce air leaks and improve cooling consistency. What it does:

• Seals the damper opening to prevent warm or humid air from entering the cooled compartment
• Helps maintain consistent internal temperatures and more efficient cooling
• Commonly replaced when the damper area shows visible gaps, cracks, or air leakage
• Can reduce frost buildup or uneven cooling caused by a compromised damper seal

• One damper sealing gasket

• Disconnect power before starting any repair to avoid electrical shock
• Remove the damper housing or cover per your model's service instructions to access the seal
• Inspect the damper and surrounding area for damage; clean mating surfaces before installing the new seal
• Handle gently and seat evenly to ensure a full seal; test operation after restoration of power

This plenum gasket creates a tight seal around the refrigerator's plenum assembly to help direct airflow and reduce frost buildup. It replaces a worn or damaged gasket to restore proper airflow control and help maintain efficient cooling. What it does:

• Seals the plenum chamber to prevent air leaks that can reduce cooling efficiency
• Helps direct cold airflow from the evaporator into the fresh food/freezer compartments
• Can reduce frost or ice accumulation caused by damaged or compressed seals
• Commonly replaced when gasket is torn, brittle, or no longer holds a snug fit

• One plenum gasket as shown

• Install with power to the appliance turned off and the unit unplugged for safety
• Remove any snapped-in trim or panels carefully to access the plenum area; retain fasteners for reassembly
• Inspect surrounding foam/adhesive surfaces and clean them before seating the new gasket for best results
• If adhesive is used, allow any recommended cure time before returning the appliance to service