Hotpoint Parts

The indication was that when I tried to use the icemaker or water dispenser, the green LED on the front would dim and the ice maker dispenser wouldn't work. It was intermittent at first, but this indicated it may be a power management issue, in that insufficient voltage was getting to the ice dispenser motor. I unplugged the unit to reset the electronics for about a minute, and when I plugged it back it the compressor would try to turn on (solenoid or relay would click about every two... Read more

Ordered all the parts Read more

It was one of 3 things basically, motherboard, pressure sensor or fill valve. I tried cleaning the pressure sensor to no avail. I proceeded to replace both the valve and the sensor because the parts were very inexpensive and the cost of a motherboard wasn't worth it. I completed the repair in about 1 hour and have ran it twice without incident . Read more

• Burning smell
• Spins slowly
• Pumps but will not spin
• Noisy

Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more

Just enter the appliance model and the all the parts are pictured! Really easy! Read more

• Won't start

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

• Leaking
• Not dispensing water

We noticed a puddle of water in front of the fridge a couple of months ago-dried the floor up both times and thought someone had dropped ice-or spilled water. A couple of weeks ago there was water dripping through the dropped tile ceiling in the basement. I shut off the water for the water supply to the fridge at the copper pipe in the basement and removed some of the tiles which felt a little damp. It still dripped all day. When my spouse came home he pulled down more of the tiles. It was as... Read more

• Not dispensing water
• Leaking
• Ice maker not making ice
• Ice maker won't dispense ice

To verify if you have a bad valve in the first place read on... I first pulled out the ice maker to remove all the frozen water including the inlet section which was a huge solid waterfall of ice. While it was out completely disconnected I cleaned/chipped out the freezer section ice puddle. I also completely melted the ice cubes and ice puddles off the ice maker at the fill bucket end in the sink with running water careful to not get water near the power cord area. I then put a tall plastic cup... Read more

Ordered a new heating element. Read more

Replacing head burner d solved the problem. The 8 year old original developed a mild warp, replacing it was the solution. GE gas cook top Model JGP933SEK1SS. I replaced the other burner caps for a cosmetic renewal. Read more

Replaced the gaskets on refrigerator and freezer doors. Read more

• Won't start

The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more

• Too hot
• No heat or not enough heat
• Takes too long to dry

Replaced thermal stats Read more

I ordered a new switch from APP and fixed my fridge. However, the video posted for this repair on this site is not applicable to newer refrigerator models. I have a 2015 GE GTE18IHCRSS and had to drop the control housing (#432 in the diagram) to attach the wire/plug assembly to the switch. Only had to remove the front screw with a 1/4" nut driver and that provided enough of a gap for me to plug in the switch. So the correct method to replace the light switch in a newer model refrigerator is as... Read more

Replaced freezer and refrigerator gaskets Read more

My refrigerator's cooling fan was making a noise. It wasn't loud; in fact, it was barely discernible. However, it was just loud enough to annoy me. The fan blade was hitting the shroud every now and then, creating a subtle, yet annoying sound. I'd tried tightening all the screws back there, and it helped-for a while. The noise came back. After looking at the fan motor, I noticed the bushings; it occurred to me that they might be the culprit. And why not? They were the originals installed at the... Read more