Husqvarna Parts

The cutting chain on a garden tiller is used as the primary chain to help drive the unit across the soil. Over time, the chain can start to stretch and may not work as well as it did when new. It can also break entirely and require a full replacement with a new cutting chain. Inspecting the chain can give insight into whether it is stretched or has broken and requires a repair or replacement.A screwdriver and a set of wrenches will be needed to replace this part. The process involves removing all of the components out of the chain case. Next, the bolts that hold the case together will need to be taken out. Once the cutting chain is removed from the tiller, the new replacement part can be placed in the same location. After it has been placed, the rest of the parts will need to be reassembled before using the tiller.This cutting chain is compatible with Husqvarna, Poulan, AYP, McCulloch, Poulan Pro, RedMax, Weed Eater, Jonsered, and Craftsman tillers. It comes as an individual OEM replacement part that is sourced directly from the manufacturer.

This is a genuine replacement flange bearing intended for use on lawnmowers and lawn tractors. The flange bearing is a part located between the rim and tire. Its main function is to secure moving parts while still allowing rotation and guiding movement in the correct direction. The flange bearing is a very high wear part, so it is likely to need replacement. As it wears, the bearing can break, which causes the wheel to wobble and eventually fall off the machine, making it impossible to use. If left untreated, a broken or excessively worn flange bearing can damage multiple parts around it.Replacing the flange bearing is relatively simple. Start by supporting the machine and propping the wheel off the ground. Remove the dust cap and retaining ring. Then remove the tire from the axle, and be sure to notice where the washers are located. Knock the flange bearings free from the rim with a hammer. Then reverse these steps to install the new bearings. Lastly, lubricate the newly installed parts with some grease.This genuine OEM replacement Flange Bearing is sold individually. It is designed to work with several Craftsman and Husqvarna lawn tractors and lawnmowers.

This replacement part is a bearing. It is a genuine replacement part made by Husqvarna. Bearings are used in and around the engine to assist different parts in their rotating mechanisms. They are used to provide additional space to move as well as prevent too much friction from occurring. A new bearing might be needed if the user notices unusual noises coming from inside the appliance or machine. When bearings are damaged, parts rub together and create loud noises. Be sure to wear working gloves during this repair as the bearing could be close to other sharp objects and the user might be in danger of being injured. This part is a genuine OEM replacement part. This bearing is sold individually and is sourced directly from the manufacturer.

This replacement part is a tiller chain intended for use in lawn equipment. This is a genuine replacement part made by Husqvarna. Tiller chains link parts of the machine so that the entire appliance can run smoothly. These chains ensure that the parts in the tiller or cultivator are rotating smoothly.A new tiller chain might be needed if the current one is damaged or broken in any way such as being split or torn. The user might be able to tell when the tiller chain is malfunctioning if there are unusual noises coming from the machine. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. It is recommended that the user refer to the appliance manual for more detailed instructions on how to install this part. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with lawn equipment made by Husqvarna.

This is a push nut that is used in many different models of lawnmowers. It's a black nut made of durable metal. The push nut is used to secure various components in several locations on lawn and garden equipment. This component is made of strong materials but it can experience damage, wear and tear, or even break over time. This can cause the lawnmower to perform poorly or experience other issues. This is a small component that can be broken or lost and needs to be replaced to ensure the best performance from the lawnmower. A set of pliers and a screwdriver may be required to replace the push nut. The parts that will need to be removed before replacement vary based on the location of the push nut. Disassemble any components in the way before taking out the bad or damaged push nut. Place and tighten the new nut and reassemble the parts.This is a genuine OEM replacement push nut that is directly sourced from the manufacturer. It is sold as an individual component. The push nut is created for use with lawnmowers manufactured by Craftsman, Husqvarna, Weed Eater, Poulan, Murray, Ariens, and Dixon.

A flat washer is used in conjunction with threaded screws or bolts. Before inserting and fastening a bolt into the surface, the fastener is inserted through its end. This is a typical application of washers because they distribute the fastener's load. It also helps with heat and friction reduction as the fastener is tightened. In some implementations, a flat washer also works as a spacer, as well as additional electrical insulation. A flat washer is made from metal. However, it can break down. One of the warning signs of a bad washer is that it doesn't have its distinct circular shape, appearing bent or cut in half. Replacing a flat washer is easy, however, and only requires a screwdriver or socket wrench (depending on the type of fastener). Loosen and remove the fastener. Then, take the broken fastener out. Insert the new flat washer into the fastener. Then, screw the fastener back. This flat washer is an original Husqvarna product. It is made for lawnmower models manufactured by Craftsman, Murray, Husqvarna, Ariens, Poulan, and Weed Eater. It is made of metal and is sold individually. Fasteners are not included.

This tire is a genuine Husqvarna part, sold individually. This tire can be used as a replacement part for a lawn mower. The purpose of a tire is to facilitate the steering of the appliance so an operator can navigate the appliance over a variety of surfaces in order to mow and clip the greenery.The tire of a lawn mower might have to be replaced at some point within the standard lifespan of the appliance if the tread or the internal structure is punctured, torn, ripped, scraped, or eroded beyond repair. If this occurs, the tire should be removed and replaced by this genuine OEM replacement part before using the lawn mower again. It is a simple repair process that will require only basic tools. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This tire is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Poulan, Murray, Ariens, and Dixon.

This tire is a genuine Husqvarna part, sold individually. This tire can be used as a replacement part for a lawn mower or a lawn tractor.The tire for a lawn mower or a lawn tractor might eventually have to be replaced if it shows signs of damages that cannot be fixed by a basic repair. If the tire has been damaged, it should be removed and replaced with this genuine OEM replacement part before using the appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This tire is compatible with the following outdoor appliance brands: Husqvarna, Poulan, Weed Eater, and Craftsman.

Here is an authentic replacement drive belt from the manufacturer for riding mowers and tractors. It is a replacement for the original belt that came with the machine. The drive belt is also known as the V-belt. This belt is used as a link between the transmission pulley and the engine pulley. The belt provides the mower with the capability to drive. The drive belt gets a substantial amount of use, which means it is subject to wearing down over time. When a belt becomes worn, it can start to stretch, and it could even tear or break entirely. If this were to happen, the mower would no longer be capable of driving. Owners need to check the condition of their belts several times a year if the mower has been used frequently. Replace the belt as needed. The genuine OEM replacement drive belt is sold individually. The belt can work with more than 150 riding mowers and tractors from several brands. It is compatible with certain makes from Husqvarna, Craftsman, and Ariens.

This v-belt is a genuine Husqvarna part, sold individually. This v-belt can be used as a replacement part for a tiller. The purpose of a v-belt is to affix the pulley of the motor to the drive mechanism of the appliance so the wheels are rotated, and the appliance can be operated properly.The v-belt might have to eventually be replaced if it suffers damage that cannot be fixed through a simple repair process. A damaged v-belt should be removed and replaced by this genuine OEM replacement part before using the tiller again. It is a simple replacement process that will require only basic tools. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This v-belt is compatible with the following outdoor appliance brands: Husqvarna, Poulan, and Craftsman.

This is a V-belt made from durable materials and designed for use on a variety of lawn and garden equipment. The main job of the V-belt is to ensure the tines on a tiller are rotating properly. While it is made of strong materials, the V-belt can break or wear out over time. If the belt is extremely worn, the tool may no longer operate the way it should since the part can slip off of the pulley.This V-belt is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual part. The belt can be used with lawnmowers, tillers, and snowblowers manufactured by Husqvarna, Poulan, Weed Eater, and Craftsman.

This genuine OEM part is a bushing for lawnmowers. The bushing is the plastic piece that goes into the wheel, allowing it to turn smoothly. If the wheels of the mower are no longer turning smoothly, the bushings might need to be replaced. Luckily, replacing a bushing is a relatively simple task.To replace the bushing, start by removing the wheel assembly from the mower. Unfasten the bolts that secure the wheel. Once removed, locate the old bushing and slide it out of its place. Slide the new bushing into the proper position. Reinstall the wheel assembly and make sure the bolts are tightened securely. Once secured, test to see if the wheel is rolling smoothly. If it is, then the installation was a success.This replacement part is sold individually and is compatible with Husqvarna brand lawnmowers.

This type of lawnmower blade is characterized by deeper curves on the ends, which create enough suction to circulate and expel the grass clippings into a bagger. It is designed to improve the way clippings are ejected out of the discharge chute. It also has larger wind wings that increase airflow. This helps prevent clogging when mowing wet or tall grass. Without a bagger, these blades put excess load on the engine and don't expel clippings as efficiently as low lift blades.  The wear and tear on a high lift blade are considerable, so there's a risk of using a dull blade without regular replacement. Blade erosion can happen over time due to debris, and the mower may offer noticeably less efficient performance when cutting grass. It is time to replace the blade if it has nicks and dents. For the average homeowner, a good rule of thumb is to replace the mower blades annually.  This part is compatible with specific models from Ariens, Craftsman, Husqvarna, Poulan, and Murray. It is an OEM part sourced directly from the manufacturer and is sold individually.