Jenn-Air Range Parts

This contact assembly restores a reliable electrical connection within an appliance's control circuit. Replacing worn or pitted contacts helps eliminate intermittent operation and arcing so the controlled component can turn on and off consistently. What it does

• Provides the conductive interface that completes the circuit when the control is engaged
• Helps deliver stable power to the connected load
• Typical failure signs: intermittent operation, no operation of the controlled component, visible heat damage/pitting on contacts, arcing or buzzing at the contact point

• 1 contact assembly

• Disconnect power to the appliance before servicing and verify no voltage is present
• Access the control area; photograph or label wire positions and terminal orientation
• Move wires one at a time to the new assembly; ensure tight, clean connections
• Inspect nearby wiring for heat damage and replace any burnt terminals; test operation before reassembly

This oven door hinge supports and guides the door through its range of motion so it opens smoothly and seals tightly when closed. Replacing a fatigued hinge restores proper door alignment and consistent oven performance. What it does:

• Provides spring-assisted tension to control door opening and closing
• Helps the door seal evenly against the gasket to retain heat
• Maintains correct stop positions to prevent slamming or over-travel
• Common symptoms: door won't close fully or pops open, drops/slams, sits crooked, heat escaping/long preheat

• One door hinge assembly

• Disconnect power at the breaker; allow the oven to cool completely before servicing.
• Remove the door per your model's procedure (often open to the broil stop, engage hinge locks, then lift off).
• Use hinge locks/pins to control spring tension and prevent snap-back during removal/installation.
• Support the door to avoid damage; many replace both hinges together to keep tension balanced.

This replacement jack mounts inside the oven cavity and provides the receptacle for the food temperature probe. It restores a dependable connection so the control can monitor internal food temperature and operate probe-cook features as intended.

• Provides the in-oven receptacle for the food/meat temperature probe
• Carries the probe's signal to the control during probe-cook cycles
• Helps resolve issues where the control does not recognize a probe or the probe feature won't run
• Replaces a jack that is damaged, corroded, or loose

• Disconnect power at the breaker and allow the oven to cool completely
• Access from inside the oven; remove the mounting screw(s) and carefully pull the jack to reach the wire harness
• Transfer/connect the harness and seat any gasket or insulation to maintain the oven cavity seal
• Do not overtighten fasteners; avoid pinching or damaging wires and insulation

This plug-in coil cartridge restores reliable surface heating on compatible modular cooktops. Replace a worn or damaged module to regain consistent burner performance and maintain a matching black finish. What it does:

• Provides electric surface heat via a self-contained coil cartridge that plugs into the cooktop receptacle
• Helps resolve issues like a surface burner not heating or heating intermittently
• Addresses problems from visible damage or burned/loose cartridge terminals
• Preserves proper fit and appearance for black-finish cooktops

• 1 coil cartridge assembly

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift out the old cartridge; inspect the cooktop receptacle for heat damage before installing
• Align guides and terminals; seat the cartridge fully without forcing the connection
• Restore power and test burners at low/medium settings first

The black Cooktop is an OEM part for Whirlpool ranges. It serves as the flat surface where cooking is done by using burners or a warming element. The glass-ceramic or stainless steel cooktop provides an attractive and durable cooking area. 

Symptoms of a bad cooktop include: 

• Cracks or chips in the glass or surface material
• Burned, stained, or discolored areas that cannot be cleaned
• Dents or depressions that collect moisture or debris
• Inoperable or intermittent burners or heating elements

Causes of a bad cooktop can be cracks or damage from impacts or heavy pots/pans, heating element failures over time, surface deterioration from abrasive cleaners, or prolonged heat exposure. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This safety thermostat monitors internal temperature and opens the circuit if the appliance overheats. Replacing a failed high-limit thermostat restores heat and helps protect controls, wiring, and nearby components from thermal damage. What it does:

• Monitors temperature and interrupts power to the heating circuit if an unsafe temperature is reached
• Helps prevent overheating damage to internal components
• When failed open, can cause no heat or cause the unit to shut off during high-heat operation
• At room temperature it should read closed/continuous; an open reading indicates replacement is needed

• 1 high-limit thermostat

• Disconnect power at the breaker (and shut off gas supply if applicable) before servicing
• Access location varies by model; commonly mounted to the oven cavity, plenum, or rear panel
• Transfer wires one at a time and mount the thermostat flush to its surface or bracket
• After replacement, verify proper airflow/cooling and address any root causes of overheating

This oven door gasket restores a tight seal between the door and the oven front frame. A proper seal reduces heat loss, supports accurate temperatures, and helps food bake and roast more evenly.

• Creates a heat-resistant seal at the door-to-cavity opening to contain heat and airflow
• Helps maintain stable oven temperatures and normal preheat times
• Replace if the seal is torn, frayed, brittle, flattened, burned, or leaking
• Helps resolve heat escaping around the door, uneven baking, or longer cook times

• Disconnect power; for gas appliances, also shut off gas. Allow the oven to cool completely
• Remove the old gasket by releasing end retainers or pulling it from the channel; clean the groove
• Install the new gasket without stretching; seat it evenly around the perimeter with corners aligned
• Close the door and check for uniform contact all around; adjust as needed per your model instructions

The Top Burner Control Knob is an OEM part for Whirlpool ranges and cooktops. This part is crucial for the precise control of the heat output from the burners, allowing users to adjust the flame or element temperature accurately. It fits directly onto the stem of the burner switch, providing a tactile interface for easy operation. 

Causes of a bad Top Burner Control Knob can include cracking, melting, or fading from exposure to heat or aggressive cleaning, as well as internal damage that can prevent the knob from engaging with the burner switch correctly.  

Symptoms of a bad Top Burner Control Knob include:

• Difficulty in turning the knob or a lack of resistance which indicates a failure to engage with the burner switch.
• Visible damage such as cracks, warping, or melting that interferes with function.
• Faded or worn labels that make it difficult to see the settings.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:

• Protects the line and control circuits from shorts and overloads
• Time-delay design helps prevent nuisance opening during startup surges
• When open, the unit will be completely dead—no display, lights, or response
• Repeatedly opening usually indicates an unresolved electrical fault that needs diagnosis

• 1 time-delay fuse

• Disconnect power at the breaker before servicing; some appliances can retain dangerous high voltage
• Replace only with the same type and rating specified by the manufacturer
• Inspect the fuse holder and wiring for heat damage or loose connections before reassembly
• If the new fuse opens immediately, stop and diagnose the underlying cause; never bypass or upsize a fuse

This is a Whirlpool range control panel assembly. It houses the display, user interface buttons, and has space for temperature control knobs. With extended use, the buttons on a control panel may wear out or stop responding to user input.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the old control panel in place. Remove the screws from each side of the old control panel to disconnect it, then carefully remove any boards or other components installed within the panel. Once it has been completely removed, the new control panel can be installed in its place.This is a genuine OEM part compatible with ranges manufactured by Jenn-Air, but may also work with other Whirlpool brands, including Maytag, KitchenAid, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

The Screw is an OEM part for Whirlpool microwaves. It is responsible for securing various parts of the microwave together. This screw ensures a tight and secure fit for parts and helps maintain the structural integrity of the microwave, preventing any loose or rattling parts.

A bad microwave screw can occur due to wear and tear, accidental damage, or misplacement during maintenance or repairs. If you notice symptoms such as loose or wobbly components, difficulty in opening or closing the microwave door, or abnormal noises while the microwave is in use, it may be time to replace this part.

Symptoms of a bad microwave screw include:

• Loose or wobbly components
• Difficulty in opening or closing the microwave door
• Abnormal noises during operation

Restore your Whirlpool microwave by replacing the faulty or missing microwave screw with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.

This oven door seal creates a tight, heat-resistant barrier between the oven door and front frame. A good seal helps the oven heat efficiently and prevents hot air from escaping into your kitchen.

• Cushions and seals the perimeter of the main oven door to contain heat
• Helps maintain stable cooking temperatures and energy efficiency
• Resolves issues like heat escaping around the door, uneven baking, longer preheat times, or visible gaps in the gasket
• Replaces a flattened, brittle, cracked, or torn door gasket

• Disconnect power and allow the oven to cool completely before service
• Open the door and remove the old gasket from its retaining clips or channel
• Press the new seal evenly into place, ensuring corners seat fully
• After installation, check door alignment and seal contact all around

Color: black. It measures about 2 inches in diameter.

This broil element provides the intense top heat your oven uses for broiling. Replace a failed or damaged element to restore consistent broiler performance and proper browning when broiling meats and other foods.

• Supplies high, direct radiant heat from the top of the oven during broil cycles
• Restores proper broiling performance for browning and searing
• Replaces elements with open circuits, blisters, cracks, or shorts
• Common symptoms include: broiler won't heat, weak or uneven broiling, visible damage, or the breaker trips when broil is turned on

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and disconnect wires; support wires so they don't slip back into the rear cavity
• Attach wires to the new element and secure with existing screws; avoid bending the element or overtightening
• Restore power and test the broil function