Jenn-Air Range Parts

• Won't start
• Element will not heat

Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

1st. replaced thermostat probe inside wall oven - no change. Then removed range heating element and measured it with ohm meter for continuity and found it to be OPEN. Ordered replacement range heating element; measured it before install and found it to be a few ohms - installed in less than 5 minutes and tested. ALL WORKS GREAT. Both items purchased with shipping were just over $100. (I chose to keep the thermostat probe instead of returning it being the oven is just over 10 years old). Read more

We bought replacements which fit very well and the burner elements are level again! Read more

Bought a replacement gasket. Read more

Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks. Read more

If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well. Read more

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more

I replaced the bake element in the bottom of the unit. Read more

I did research on my own prior to ordering. I looked at other sites, but was impressed with the online chatting-this was very helpful! I ordered three items and had difficulty with one rack. I called customer service and received a new rack the next day. This was meaningful to me because we were heading back home in a few days. The rep was very understanding to my situation and helpful. Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

I researched on the net, ordered the part, it arrived the next day. Took about 45 minutes to replace. Fairly easy fix. Read more

I found my model number on AppliancePartsPros.com very easily and found the new element and temperature sensor kit. The temperature has always been a little off, so I figured I needed the new sensor. I am glad I also ordered the element. When I took everything apart I discovered that the wire connector had burned off and the element was no good anymore. I had a spare connector in my tool box, so I crimped it on, and put everything back together. Now the oven heats quickly and I believe it is... Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more