Need Help?
Call
Ice dispenser only making crushed ice instead of cubes? This solenoid valve kit fixes the cube/crushed ice selector. Easy DIY repair with video guide.
This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more
Protective cover for the ice maker's infrared emitter sensor in the freezer compartment. Replace if cracked, broken, or missing to shield the sensor.
Followed the video you provided. Read more
Protective cover that secures and encloses the water filter in your refrigerator's interior. Replace if cracked, broken, or tabs are damaged.
Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more
Protective cover that encloses the drive belt and motor pulley. Replace yours if cracked, warped, worn through, or missing to shield moving parts.
There was a horrible screeching noise coming from the washer, and upon inspection I found that the retaining nut that attaches the cam to the machine was either improperly tightened to begin with or had worked itself loose causing the cam to wobble and the belt to work down the cam. The cam gear teeth became worn and the belt worked itself half off the cam and cut a hole in the protective plastic screen containing the whole ensemble. I purchased the belt, shield and cam kit. The parts are... Read more
Allows water to flow directly to your dispenser and ice maker without filtration. Install when choosing not to use a water filter. Confirm fit by model.
Replaced filter with plug. Read more
Cracked or missing ice maker cover exposing internal components? This protective cover shields the ice maker assembly. Simple DIY install in minutes.
Replaced icemaker and shutoff arm. Easy project. Read more
The Water Inlet Valve is an OEM replacement part for Whirlpool dryers. Located where the water supply line connects, it controls the flow of water into the dryer drum for steam cycles. Precise control is needed to prevent temperature fluctuations or flooding. Causes of a bad inlet valve can include mineral buildup clogging water pathways, worn diaphragms allowing constant flow, or mechanical linkage issues. Symptoms of a bad water inlet valve include:
This OEM replacement part is compatible with brands like Maytag, KitchenAid, and more.
Ordered new valve. Easy installation. Saved a service call charge (-; Read more
Plastic trim bezel that mounts around the lid lock on your top-load washer's panel. Replace if cracked, broken, or missing to restore a clean finish.
Put in new lid lock. This is my second one in 1 year. Whirlpool suggested I leave it loose so that if somebody did try and force it open, it wouldn't break it. This lid lock has 4 wires and cannot be bypassed. Read more
Protective cardboard or plastic cover that installs over the internal cooling system and wiring. Replace if cracked, torn, ripped, or missing.
I had to make a few different holes in the cardboard but it worked great! Read more
Covers the rinse aid dispenser compartment on your dishwasher door. Replace if cracked, broken, missing, or won't stay threaded properly.
The drying agent lid was broken for a couple years now and our dishes would never dry completely. We finally decided to google for Kenmore parts and this website came up. Couldn't believe how easy it was. All we had to do was find the brand and model number and all the parts showed up on Appliancepartspros.com website. We scanned thru the list found the lid and ordered. It arrived within 2 days. Viola!! Now we wish we had done this much earlier. Thank you for such a smooth experience. Read more
Secures the door shelf bar in refrigerator doors, providing a finished look and stability. Replace if cracked, broken, or missing to restore support.
Ordered bar from ApplianceParts Pros and two end caps. Had to cut the bar to size create a new cutout for the end cap on the cut end, install the end caps and voila, now I can use that shelf again. Seemed a little pricey for a 20 year old fridge but why not fix it if it’s working. It’s the garage fridge. Tools: hacksaw and diagonal cutters to make the cutout Read more
Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.
Took top off and did a line at a time Read more
Replacement flip-up door that covers the lint screen opening in your dryer's front bulkhead. Needed when original door is cracked, broken, or missing.
There is no good diagram explaining how exactly these fit in. I had to do trial and error. The parts are quite delicate so I actually broke one trying to get it in. I would recommend ordering an extra or two. These need springs tonfit correctly. Luckily I saved the old ones...if you don't have them, it won't work. Unscrew the two screws on outside and two inside. You don't have to take whole thing out, just loosen. Look carefully and you can see the two little holes in the plastic where... Read more
This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.
Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more
This is the exterior air grille that covers the dryer's exhaust outlet, directing warm, moist air out of the appliance. It helps protect internal components and maintain proper airflow during the drying cycle. Replace this grille if it is cracked, warped, or has broken louvers that could restrict airflow and reduce drying performance.
Was an easy fix with the new part and instructions. Read more
This cover assembly attaches to the back or bottom of the refrigerator to enclose and protect the compressor and related components. It helps keep dust and debris away from the compressor area while providing a finished appearance. Replace this cover if it is cracked, broken, or missing, which can allow dirt buildup on the compressor and condenser that reduces cooling efficiency.
Ordered all the parts I needed to finish off a Craigslist purchase that had some cosmetic and function items missing. Thanks for all the parts at great prices! Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.