Kenmore / Sears Dishwasher Pump

The Circulation Pump is an OEM part for Whirlpool dishwashers. This component drives the water flow throughout the dishwasher, ensuring efficient cleaning performance. It helps to distribute the water evenly, reaching every corner of the dishwasher, and effectively removing food particles and stains.

Causes of a faulty circulation pump can include wear and tear over time, blockage due to debris or foreign objects, or electrical component failure. These factors can result in reduced water pressure, inadequate cleaning, or the dishwasher not operating at all.

Symptoms of a bad circulation pump may include:

• Weak or no water spray during the wash cycle
• Incomplete or unsatisfactory cleaning results
• Unusual noises coming from the dishwasher

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This is a dishwasher circulation pump. The circulation pump is located inside the dishwasher and includes an impeller and a motor. The purpose of the circulation pump is to provide a means for water to be forced into and out of the wash arms. If this part is damaged or faulty, the dishwasher may not clean properly or may make much more noise than is expected.The first step to replace the circulation pump is turning off the water supply and electrical power to the appliance. Take off the spray arms before removing the toe panel and bottom access panel. Pull the dishwasher away from the wall before removing the drain pump. Use a towel to catch any water. Next, remove the circulation pump and the motor assembly. Transfer the small parts to the replacement part and install it into the dishwasher. Reassemble and reconnect water and power before using the appliance.Made for dishwashers manufactured by Kenmore, Whirlpool, and KitchenAid, the circulation pump is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Circulation Motor is an original and genuine OEM replacement part for Frigidaire dishwashers. It circulates water throughout the wash and rinse cycles to clean all dishes.

Causes of a bad circulation motor include normal wear and tear over time, the mineral buildup that causes mechanical issues, or damage from overfilling the dishwasher with an unbalanced load.

Symptoms of a bad circulation motor are:

• Dishes only partially cleaned with dirt and food soils still stuck on
• Incomplete water coverage inside the dishwasher tub
• Puddles of standing water after a cycle
• Abnormally long cycle times

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Westinghouse, and some Kenmore dishwasher models.

This is a replacement circulation pump. This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This part is intended to replace a broken, faulty, or clogged circulation pump in a variety of dishwashers. The circulation pump transfers water to the spray arms so dishes can be cleaned. If the pump is defective or becomes clogged over time, dishes may not come out clean or the dishwasher may leak. Proper tools are required to install this part. Make sure that the dishwasher is entirely disconnected from water and power before starting any repair work. Always ensure the appropriate safety precautions are adhered to when attempting to fix any appliances. For more accurate information on how and where to install this circulation pump, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this circulation pump is suitable for use on several different models of dishwashers manufactured by Whirlpool, Maytag, KitchenAid, Amana, and other Whirlpool brands. This is a genuine part made of high-quality, non-corrosive, durable materials and is sold individually.

The Blower Motor Assembly is an OEM replacement part for LG dishwashers. Located inside the wash cavity, it functions to distribute heated air throughout during the dry cycle. Rapid rotation of the blower motor blades works to eject moisture from dishes and ensure thorough drying. 

Causes of a bad blower motor include failure of the motor itself, cracks in the blades that disrupt airflow, or bearing issues preventing proper rotation.

Symptoms include:

• Dishes still feeling damp after a cycle 
• Puddles of water remaining in the bottom of the dishwasher
• Water droplets on upper racks/dishes
• The motor producing grinding/squealing noises on startup

It is also compatible with some Kenmore dishwashers using LG components. 

This OEM Replacement Part is a rubber connector with female threads. It is designed to provide a secure connection between the spray arm and the pump in a dishwasher. The connector measures 2-3/4 inches in diameter and 2-1/8 inches in height. This part is crucial to ensuring the proper functioning and efficiency of your dishwasher's spray arm pump.

Over time, the pump connector can wear out or become damaged due to repeated exposure to water, detergent, and high temperatures. This wear and tear can lead to leaks or a decrease in the dishwasher’s performance.

Symptoms of a bad pump connector include:

• Water leaks under or around the dishwasher
• Reduced water pressure during the cleaning cycle
• The dishwasher not draining properly
• Unusual noises during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: This connector has female threads. For male threads use WD18X206.

The Sump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is the pump and motor that circulate water throughout the unit. This assembly ensures that water is efficiently pumped through the spray arms, providing thorough cleaning of dishes.

Causes of a bad sump and motor assembly can include debris buildup, wear and tear from regular use, or damage to the motor or pump components. 

Symptoms of a bad sump and motor assembly include:

• Water leaks under the dishwasher
• Unusual noises during operation
• Incomplete or poor cleaning of dishes
• Dishwasher not draining properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Shaft seal included.

Due to manufacturer changes, part may differ in appearance and will include two o-rings.

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This assembly is responsible for draining water from the dishwasher during the drain cycle and recirculating water during the wash cycle. It works continuously throughout the cleaning process to remove dirty water and reuse clean water.

Causes of a bad pump and motor assembly include failures in the motor that drives the pump or internal clogging/blockages of the pump mechanism. 

Symptoms of a bad pump and motor assembly include:

• Incomplete draining of water at the end of the cycle  
• Leaks or flooded bottom of the dishwasher
• Loud vibrating or grinding noises coming from underneath during the operation
• The dishwasher failing to fill or recirculate water properly

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This circulation pump and motor assembly drives water through the spray arms during the wash and rinse cycles. Replace it to restore proper wash performance when the dishwasher fills but doesn't spray, cleans poorly, or runs loudly. What it does:

• Circulates water from the sump through the spray arms for cleaning and rinsing
• Also called the wash motor; provides the pressure needed for effective spray
• Typical failure symptoms: poor cleaning, no spray or weak spray, loud humming/grinding, or leaks at the pump area
• Restores normal water circulation and wash pressure

• One circulation pump-and-motor assembly

• Disconnect power and shut off water supply before servicing
• Access from the bottom/front of the unit; expect residual water—protect floors and wiring
• Move wiring and hoses carefully; transfer any clamps, seals, or brackets from the original as needed
• Ensure seals are seated, reconnect hoses/wiring, then run a short cycle and check for leaks

The Sump Cover and Filter is an OEM part for Frigidaire dishwashers. Located inside the bottom of the tub, it seals off and protects the drainage sump where debris collects after each wash cycle. The attached mesh filter screens out particles that could otherwise clog drain lines.

Causes can involve mineral buildup that blocks the filter mesh over time, cracks in the plastic housing exposing the sump, or a missing or damaged filter that fails to trap solids.

Symptoms of a bad sump cover and filter include:

• Standing water inside the bottom of the dishwasher tub
• Reduced drainage or water removal after cycles complete
• Floating debris trapped near the drain pump area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

The Pump & Motor is an OEM replacement part for Whirlpool dishwashers. As the main component for water circulation, it contains both the water pump and motor required to power it.

Causes of a faulty pump & motor assembly can include bearing or seal failure from prolonged use, dried pumps from excess mineral build-up, or stuck/jammed impellers no longer spinning freely.

Symptoms of a bad pump & motor include:

• Inability to fill with water or drain properly
• Noisy rattling sounds coming from inside the machine
• Failed or incomplete wash cycles
• Leaks developing around the pump area

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This is a circulation pump motor for dishwashers. It controls the main pump of the appliance.The pump is directly responsible for removing extra water from the dishwasher after use. When a dishwasher's circulation pump motor goes bad, the main indicator is usually leaking from the appliance. There will be a noticeable amount of water emerging from the bottom of the machine whenever the cycle is engaged. Unplug the dishwasher from its main power source and water hookup. Remove the dishwasher from its space in the counter. Remove all necessary entry plates to access the interior of the dishwasher. There is a metal bracket holding the current motor in. Unscrew the two screws that secure the bracket and remove this component. Remember which way the motor is oriented before removing it. Unplug the power cable connecting the motor to the dishwasher. Put the two new sealing rings on the new pump motor. Repeat these instructions in reverse to install the new part.This Frigidaire dishwasher circulation pump motor is a genuine OEM replacement part sourced directly from Frigidaire. The pump motor is sold individually. This part is compatible with Frigidaire, Kenmore, Westinghouse, and Gibson appliances.

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.