Kenmore / Sears Heating Element

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This oven bake element is the heating element that warms the oven cavity for baking and roasting. Replacing a damaged element restores proper oven heating and helps return cooking performance to normal. What it does:

• Heats the oven interior for baking, roasting and browning.
• Replaces elements that are visibly burnt, cracked, broken, or no longer glow when the oven is on.
• Common symptoms it can fix: little or no heat from the oven, uneven cooking, or an element that sparks or shows burn spots.
• Works as the direct heater inside the oven cavity; connects to the oven terminal block.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access typically requires removing the oven interior panels or rear access panel; support the element while disconnecting terminals.
• Handle terminals and sharp sheet metal carefully; use insulated tools and secure terminal connections.

This oven heating element replaces a failed bake element to restore even, reliable oven heat for baking and roasting. It's a direct-replacement style part that heats the oven cavity when the bake function is used. What it does

• Heats the oven cavity during bake cycles so food cooks evenly
• Commonly used when the oven won't reach or hold baking temperatures
• Can fail visibly (broken or burned) or electrically (open circuit)
• Works with the oven's temperature control to maintain set temperature

• Disconnect power at the breaker before starting any repair to avoid shock.
• Handle the element carefully; connectors and terminals can be fragile.
• Confirm wire terminal fit and secure mounting; replace only with the correct OEM-style element.

Restore reliable oven heat with this bake element. It produces the lower-oven heat during the Bake cycle, so replacing a failed element brings back normal preheat times and consistent, even results.

• Supplies primary heat from the bottom of the oven during Bake
• Common fix for: no heat on Bake, very slow preheating, uneven baking/browning
• Replace if the element is blistered, cracked, pitted, or has visible breaks
• Helps restore accurate, stable baking temperatures

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; take out the element's mounting screws to free the bracket
• Gently pull the element forward; transfer one wire at a time using insulated pliers and prevent wires from slipping back
• Re-secure the bracket/screws, ensure snug connections, restore power, and test Bake

Restore reliable heat to your dryer. This replacement heating element generates the hot air needed to dry laundry efficiently, helping cycles reach proper temperature and finish on time when the original element has failed.

• Converts electrical energy into heat to warm air passing through the drum
• Failure modes include open coil or short-to-housing
• Common symptoms: no heat, weak heat, longer dry times, visible breaks or hotspots on the coil, tripped breaker or thermal cutoff
• Useful diagnostic step: check the element for continuity and for shorts to ground

• Disconnect power before service; elements get extremely hot and retain sharp edges
• Handle the coil carefully and avoid bending or touching the bare element; support terminals/insulators during transfer
• Move any reusable brackets, insulators, or wiring from the original as required
• After installation, check related thermostats/thermal cutoffs if heat issues persist

The Surface Element is an OEM part for Frigidaire electric ranges and cooktops. It is the individual electric coil located beneath the cooktop that provides heat.

The surface element heats up rapidly upon activation in order to boil, simmer or saute foods efficiently. Its precise heating capabilities assist home cooks in meal preparation.

Causes can be mineral deposits caked onto the element surface over time reducing its ability to transfer heat properly. Excess moisture exposure can also damage internal wiring.

Symptoms of a bad surface element include:

• Burners that do not heat up at all or heat unevenly
• Lights flickering below an element when in use
• Popping, buzzing or crackling noises coming from below an element

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This 6-inch surface coil element restores reliable heat to one burner on your electric range. Replace a burned-out or damaged coil to bring back consistent, even heating for everyday cooking.

• Provides cooking heat for a 6-inch burner position on electric ranges/cooktops
• Helps resolve a burner that won't heat or heats intermittently
• Addresses uneven heating or visible hot spots on the coil
• Replaces elements with visible breaks, blistering, or burned terminals

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• For plug-in coil models: lift the element, pull straight out of the receptacle, and remove from the support/drip pan
• Align the new element's terminals with the receptacle, push firmly until fully seated, and set into the support
• Inspect the receptacle and wiring for heat damage and replace any compromised components before use

This replacement bake element heats the lower oven cavity so your range can bake and roast food at set temperatures. Restores normal baking performance when the oven isn't heating properly. What it does:

• Heats the oven's lower cavity to reach and maintain baking temperatures
• Replaces a burned-out, warped, or visibly damaged element
• Helps correct symptoms like no heat or uneven baking results
• Works with the oven control to provide consistent interior temperatures

• Disconnect power to the appliance before any service to avoid shock
• Handle element carefully; sharp edges and fragile terminals can be damaged
• Verify proper terminal connection and secure mounting during installation

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

This oven bake element heats the oven cavity so food cooks and bakes properly. Replacing a worn or broken element restores consistent heat for even baking and broiling. What it does:

• Converts electrical power into heat to warm the oven interior during bake and broil cycles
• Replaces a damaged or open element that can cause the oven to not reach temperature or cook unevenly
• Works with the oven's control system to provide steady, distributed heating
• Common symptom: oven won't heat, heats very slowly, or produces uneven cooking results

• Disconnect power at the breaker before starting any repair
• Allow the oven to fully cool and wear gloves to protect against sharp edges
• Remove the oven bottom or access panel as required, disconnect element wiring, and secure the replacement element in the original mounting
• Reconnect power and perform a short test bake to ensure proper operation

This bake element is the oven's primary heating element for baking and roasting, restoring proper oven heat so food cooks evenly. It replaces a damaged or worn element to bring back reliable bake performance. What it does

• Heats the oven cavity during bake cycles to provide consistent cooking temperatures.
• Commonly linked to symptoms like an oven that won't heat, takes too long to preheat, or produces unevenly cooked food.
• Visible damage (breaks, blisters, or heavy corrosion) or open electrical continuity are signs this element needs replacement.
• Works with the oven's control and safety systems to cycle heat as required.

• One bake element

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Allow the oven to cool completely and handle the element carefully to avoid sharp edges.
• Inspect wiring and terminal connections; replace any damaged connectors before reassembly.
• After installation, restore power and run a short bake cycle to ensure proper operation.

This 24" bake element heats the oven cavity to cook and brown food. Replace a damaged or broken element to restore even baking and proper oven heat for reliable cooking results. What it does:

• Heats the oven's lower cavity to provide the radiant heat used for baking and roasting
• Replaces cracked, burned-through, or non-heating elements that prevent the oven from reaching temperature
• Helps restore consistent baking and browning when the original element fails
• Works with the oven's control system to deliver heat when a bake cycle is selected

• Disconnect power to the appliance before beginning any repair to avoid shock hazard
• Remove oven access panels and wire connectors carefully; note terminal locations before disconnecting
• Use appropriate fasteners and gaskets as required by your oven; do not force or bend terminals

This is a replacement broil element for the oven's upper heating function. It restores high-heat broiling and top-surface browning so you can sear, brown, and finish foods as intended. What it does:

• Produces the direct, high heat required for broiling and browning
• Replaces a burned-out, visibly damaged, or non-heating upper element
• Restores even top-heat for recipes that require searing or finishing
• Helps eliminate weak or no heat from the oven's broil function

• One broil element

• Disconnect power to the appliance before starting any repair
• Allow the oven to cool completely and use basic hand tools to remove mounting screws and the old element
• Handle the new element carefully to avoid bending or damaging terminals

This genuine surface coil element replaces a damaged or non-working burner on an electric cooktop to restore even heating for everyday cooking. It fits standard countertop ranges and reconnects to the existing socket for simple swap-outs. What it does:

• Heats cookware by converting electrical power into a cooking surface heat source
• Replaces a cracked, broken, or non-heating burner element
• Fixes symptoms like no heat from a burner, intermittent heating, or uneven cooking
• Works with the existing element receptacle and trim/reflector assembly when compatible

• Disconnect power at the breaker before attempting any service
• Allow the cooktop to cool completely and use gloves to avoid cuts
• Remove and retain any trim or mounting hardware; install using original screws/connectors

Note: 6" surface element