Kenmore / Sears Heating Element

This radiant surface element restores heat to a glass-ceramic cooktop burner. Replace a failed element to bring back even, reliable heating and responsive temperature control for everyday boiling, simmering, and cooking. What it does:

• Provides radiant heat to a designated cooking zone beneath the glass cooktop
• Common symptoms: surface burner won't heat, heats unevenly, or cuts out intermittently
• Visible signs can include burned or cracked element traces or damaged terminals

• 1 radiant surface element

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift or remove the glass top to access the element
• Photograph wiring and transfer leads one at a time to the new element to maintain correct connections
• Support the element and brackets during reassembly and avoid touching the element surface with bare hands

This heating element generates the heat your electric dryer needs to dry laundry. Replacing a failed element restores consistent temperatures and helps resolve no-heat or long dry-time issues.

• Converts electrical energy into heat inside the dryer's heater assembly
• Typical symptoms of failure: runs but no heat, takes too long to dry, or clothes remain damp
• Visual clues can include a broken/burned coil or an open-circuit continuity test
• Restores proper drying performance when the original element has burned out

• Disconnect power before servicing; heating components operate at high voltage
• Access the heater assembly; note wiring and component positions for reassembly
• Handle the element carefully to avoid stretching or deforming the coil
• After replacement, clean the exhaust duct and check related thermostats/thermal cutoffs for continuity if heat issues persist

6 inch, 1200 watt single radiant surface element.

This broil element restores the oven's upper heating function so the broiler can produce proper surface browning and high-heat cooking. Replace a damaged or non-heating element to recover consistent broil performance. What it does:

• Provides the high-temperature heat for broiling and top-surface browning.
• Replaces a failed or visibly damaged upper/broil heating element.
• Common symptoms: oven won't broil, food won't brown on top, or the element doesn't glow.
• Visible breaks, blisters, or no heat when broil is selected indicate replacement.

• Disconnect power at the breaker or unplug the appliance before starting.
• Allow the oven to cool completely; wear gloves to protect hands.
• Handle the element and terminals carefully; avoid bending or nicking the heating tube.
• Secure mounting screws and electrical connectors; restore power and test broil function.

Replace the oven's lower heating element to restore reliable bake heat and more even cooking. This bake element supplies the primary lower heat during bake cycles so your oven can reach and maintain baking temperatures. What it does

• Provides the lower heating source used during bake cycles for baking and roasting
• Replaces a burned, broken, or open bake element that won't glow or heat
• Helps correct uneven baking or failure to heat on the bake setting
• Visible signs: blistering, breaks, or dark spots on the element

• Always disconnect power at the circuit breaker before servicing the oven
• Allow the oven to cool completely and wear gloves to avoid cuts from sharp edges
• Support the element while disconnecting terminal wires; secure wiring and terminal nuts when reinstalling
• Test the bake function after restoring power

This 8-inch coil surface element restores reliable heat on electric ranges. Replace a worn or failed burner to bring back consistent heating and everyday cooking performance on your cooktop. What it does:

• Heats cookware at the 8-inch cooking zone by converting electrical power into heat
• Common fix for a burner that won't heat, heats intermittently, or shows visible damage/blistering
• Plugs into the existing surface element receptacle and rests on the cooktop supports
• Helps restore even, consistent heating when the original coil has burned out

• 1 8-inch coil surface element

• Disconnect power at the breaker or unplug the range before servicing
• Allow the element to cool completely before handling
• Lift the old element slightly and pull straight out from the receptacle; avoid twisting or prying
• Align terminals and push the new element firmly into the receptacle until fully seated, then test

The oven broil element delivers intense radiant heat from the top of the cavity to sear and brown foods. Replace a burned-out or shorted element to restore reliable broiling performance and even top heat.

• Produces high, radiant heat from above when Broil is selected
• Helps sear meats and brown casseroles quickly and evenly
• Common failure signs: no heat on Broil, weak/uneven browning, visible cracks/blistering or breaks

• Disconnect power at the breaker and allow the oven to cool completely
• From inside the oven, remove mounting screws, pull the element forward, and disconnect the two wire terminals; support wires so they don't slip back
• Transfer any mounting bracket/spacers from the old element if present; reconnect terminals firmly
• Inspect and replace any heat-damaged terminals; test Broil before final reassembly

This upper oven broil element delivers direct, intense heat for broiling and top-browning. Replace a failed element to restore fast, even broiling performance and consistent top heat in your electric range or wall oven.

• Provides high radiant heat from the top of the oven during Broil for searing and browning
• May cycle on for top-browning during Bake (on some models)
• Typical failure symptoms: no broil heat or slow, uneven top browning
• Replace if the element is cracked, blistered, pitted, or sparks/arcs when energized

• Unplug the appliance or switch off power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws/clips and gently pull the element forward
• Transfer wires one at a time and support them so they don't slip back through the oven liner
• Avoid bending the new element; secure brackets/screws, restore power, and test broil

Restore reliable top heat for broiling and browning. This replacement broil heating element brings your oven's broil function back to full strength so foods brown evenly and the broiler heats when selected.

• Provides high, direct heat from the top of the oven during the broil cycle
• Helps with top-browning in some baking/roasting modes
• Common failure signs: broiler won't heat or glow, uneven browning, visible breaks or blistering on the element
• Often tests "open" (no continuity) when failed

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, then gently pull the element forward and support the wires
• Label and transfer wires to the new element one at a time; do not allow wires to slip back into the rear cavity
• Reinstall screws, ensure secure connections, restore power, and test the broil function

This replacement heater assembly restores proper heat output in your appliance. It delivers the thermal energy needed for normal operation so your unit can reach and maintain the correct temperature and complete cycles as designed.

• Generates heat for the appliance's heating/drying/defrost function (as applicable to your model)
• Helps the unit reach and maintain target temperature for proper performance
• Common failure signs: no heat or weak heat; cycles take too long or do not complete
• May trigger heating-related error/fault codes; visible breaks or hot spots on the element; tripped breaker from a short to ground

• Disconnect electrical power before servicing; allow hot components to cool
• Wear cut-resistant gloves; internal panels and chassis edges can be sharp
• Document wire routing and mounting positions before removal; route wiring exactly as original
• After installation, ensure secure connections and clearance from metal surfaces; run a brief test cycle to verify operation

Size: 8 inch. 2200 watt. Radiant.

This heater assembly restores consistent, controlled heat inside your appliance so cycles reach the correct temperature. Replacing a failed heating element assembly helps resolve no-heat complaints and performance issues that leave loads cold or extend run times.

• Generates the heat required during the appliance's heating phases so temperatures rise as intended
• Works with thermostats/sensors to achieve and maintain target temperature
• Typical symptoms: no heat, lukewarm operation, unusually long cycles, or heating-related error codes
• Often confirmed by an open element or out-of-range resistance in continuity tests

• Disconnect power and allow the appliance to cool completely before servicing
• Access the heater per the service documentation; photograph wiring and routing to aid reassembly
• Handle the element carefully to avoid bending or damaging coils; transfer any brackets/sensors from the original if they are not supplied with the new part
• After installation, inspect and clear airflow or circulation paths and verify correct voltage before test operation

This surface heating element restores reliable heat to a cooktop burner. Replace a failed or damaged element to bring back even, responsive heating performance and consistent temperature control for everyday cooking.

• Converts electrical power into heat for one cooktop burner
• Common fix for a burner that won't heat or only heats intermittently
• Can address uneven heating or erratic cycling at a set temperature
• Appropriate when the element shows visible damage or burned spots

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access varies by model; lifting the cooktop or removing the glass top may be required
• Handle the element carefully and avoid stressing the heating surfaces
• Move wires one at a time to matching terminals; ensure all connections are secure before reassembly

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance