Heating Element

Best Seller

Genuine Whirlpool part

Dryer Heating Element

4.9 (1639)

By: Whirlpool

Part Number: 279838

Restore full heat and end long dry cycles - install the Whirlpool OEM Dryer Heating Element.

Why this heating element?

Factory-spec 5400 W / 240 V heating element with nickel-chromium coil - built by Whirlpool to Whirlpool OEM standards.
Broad compatibility: fits Whirlpool, Kenmore 110-series, Roper, Estate, Amana, Maytag & more 27-inch dryers.
Built to last: high-temp terminals & mica insulation resist fatigue and hotspots.

Fixes these common dryer problems

Problem	How the element solves it
No heat / cold drum	Replaces burned-out coil to restore heating circuit
Takes forever to dry	Full wattage brings drum back to target temperature
Stops mid-cycle	Prevents over-cycling caused by faulty element
Burning smell	New coil eliminates hot-spot arcing & insulation burn

DIY install — about 20 minutes

Unplug dryer and remove back panel to access heater housing.
Disconnect wires; remove housing screws and slide assembly out.
Swap old element for new, re-use hi-limit thermostat if still good.
Re-assemble, run test cycle - enjoy fast, even drying.

This part fixes the following symptoms

No heat or not enough heat
Doesn't shut off
Touchpad does not respond

Do-It-Yourself Stories from Customers like You My 22 year old dryer just stopped getting hot Michael M. • Brunswick , GA • November 04, 2015

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

$53.95

Compare At:: $64.74
You Save:: $10.79

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Frigidaire part

Bake Element

4.9 (2412)

By: Frigidaire

Part Number: 316075103

The Bake Element is an OEM replacement part for Frigidaire ovens that provides the heat necessary for baking. Located at the bottom of the oven, the bake element heats up when electrical current flows through it, converting electricity into heat. This heat is then distributed throughout the oven cavity to cook or bake the food evenly. Measures approximately 19 ¼ inches x 17 ¾ inches

Causes of a bad bake element can include visible damage such as blistering, cracking, or splitting of the element itself. Over time, exposure to high temperatures can lead to material fatigue and eventual failure. Electrical issues, such as a short circuit or a power surge, can also damage the element, preventing it from heating properly.

Symptoms of a bad Bake Element include:

Oven not heating to the set temperature
Uneven cooking or baking results
Visible damage to the element

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Do-It-Yourself Stories from Customers like You Bake element caught on fire and burned until it broke apart at one spot Steve M. • Merritt Island , FL • July 04, 2014

It took no time to find where the problem was! I got my Frigidaire model number and got on-line with AppliancePartsPros.com where I have gone for over a decade for all my household repairs. Why? because they are honest, helpful, considerate, fast, and its easy to locate and SEE the exact part I need. 10 minutes after the burning of my element, one was in my cart and ordered! Done. TWO days later, the part arrived. I turned off the circuit breaker, unscrewed the two 1/4" screws and pulled off... Read more

$32.95

Compare At:: $42.59
You Save:: $9.64

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Heating Element

4.9 (548)

By: Whirlpool

Part Number: WP3387747

The Dryer Heating Element is an OEM replacement part for Whirlpool dryers. It is responsible for generating the heat necessary for the drying process, ensuring clothes and fabrics are thoroughly dried.

Symptoms of a bad dryer heating element include:

Clothes coming out damp or taking excessive time to dry
No heat or insufficient heat produced during the drying cycle
Visible signs of damage or burnout on the heating element itself
Unusual burning smells emanating from the dryer

Causes of a faulty heating element can include normal wear over time, electrical issues, or physical damage from impact or overloading.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

This part fixes the following symptoms

No heat or not enough heat
Takes too long to dry
Too hot

Do-It-Yourself Stories from Customers like You First longer to dry then no heat in dryer Bobbie M. • King George , VA • October 06, 2017

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

$55.95

Compare At:: $86.67
You Save:: $30.72

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Bake Element

4.9 (371)

By: Whirlpool

Part Number: W10779716

The Bake Element is an OEM replacement part for Whirlpool ovens. It is a component responsible for generating the heat necessary for baking and roasting operations within the oven cavity.

Symptoms of needing to replace the bake element include:

Uneven or inconsistent baking results
Difficulty in reaching or maintaining the desired oven temperature
Visible damage or burnout on the element itself
Unusual smells or odors associated with a faulty heating element

Causes of a faulty bake element can include normal wear and tear over time, electrical malfunctions, or physical damage due to impact or excessive temperature fluctuations.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore oven models.

Do-It-Yourself Stories from Customers like You Oven temperature was very low and inconsistant James H. • Fallon , NE • July 23, 2017

I ordered the part I was sure I needed through the Appliance Pro website. I was surprised the part arrived in just two days. FIRST UNPLUG THE OVEN.. I removed the baking racks then two screws holding the plate over the element. I then removed three screws holding the old element in place, then gently wiggle/pull the element free from the electrical connections in the back of the oven. (Note: You cannot see the connections at this point. You'll need to remove the terminal block cover on the... Read more

$50.24

Compare At:: $59.79
You Save:: $9.55

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dishwasher Heating Element

4.9 (239)

By: Whirlpool

Part Number: W10518394

The Dishwasher Heating Element is an OEM replacement part for Whirlpool dishwashers. It is a vital heating component that raises water temperatures sufficiently for sanitizing dishes during hot rinse cycles. Proper heat is essential to drying fully.

Causes of a bad heating element can include scaling or mineral deposition over time that insulates it from conducting heat. Physical damage like burnouts or breaks in coils/wires are also possible.

Symptoms of a faulty element are:

Dishes failing to get fully dry at the end of cycles
Low wash water temperatures
Buzzing, clicking or strange noises from under the dishwasher

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, and other Whirlpool-manufactured dishwashers.

This part fixes the following symptoms

Not drying dishes properly
Not cleaning dishes properly

Do-It-Yourself Stories from Customers like You Whirlpool dishwasher not fully cleaning or drying dishes. Andrew M. • Seattle , WA • January 05, 2020

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

$43.95

Compare At:: $52.74
You Save:: $8.79

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Oven Bake Element

4.9 (924)

By: Ge

Part Number: WB44X5082

The Oven Bake Element is an OEM replacement part for GE ovens. It is a critical component responsible for generating the heat necessary for baking and cooking food in the oven cavity. Measuring 18 ¼ inches wide and 14 ½ inches deep to the mounting flange. It has an element extension of approximately 2 1/4 inches past the bracket to the terminals. This element is rated at 220 volts and 2300 watts.

Causes of needing to replace the bake element can include normal wear over time, electrical malfunctions, or physical damage from impact or excessive temperature fluctuations.

Symptoms of a faulty oven bake element include:

Uneven baking or hot/cold spots within the oven
The oven not heating up to the desired temperature
Visible signs of damage or burnout on the bake element itself
Unusual smells or burning odors coming from the oven

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore oven models, ensuring a perfect fit and reliable heat generation for your specific appliance.

This part fixes the following symptoms

Little to no heat when baking
Oven is too hot
Oven not heating evenly
Won't start

Do-It-Yourself Stories from Customers like You The baking element on our 28 year old oven decided to quit on new year's eve while preheating we heard a loud crackling pop which was the element shorting out it bubbled and started smoking Cynthia B. • Waukesha , WI • January 06, 2015

Of course, these things always seem to happen on a holiday! Luckily we were not having guests for dinner - so quickly changed our eating plans for the evening. I went directly online and Googled "Bake elements for GE ovens". At first I did not think I would have luck finding this part because of the oven's age. AppliancePartsPros.com was one of the service dealers listed first and catered specifically to GE appliances and parts. So, I typed in the Model number and low and behold, a screen... Read more

$49.95

Compare At:: $59.44
You Save:: $9.49

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Heating Element

4.9 (281)

By: Whirlpool

Part Number: WP8544771

The Dryer Heating Element is an OEM part for Whirlpool electric dryers. This element provides critical heat to properly dry wet laundry loads. Consistent warmth throughout cycles is key to leaving clothes completely dry. This 5400-watt, 240-volt heating element heats the air circulating around the drum.

Causes of a bad heating element can include failure due to extended usage cycles over time, or mineral buildup inhibiting heat transfer.

Symptoms of a faulty element include:

Inability to reach or maintain desired drying temperature
Wet or damp clothes after full cycles
Potential safety issues if element overheats
Dryer not working or requiring excess cycles to dry

This OEM Whirlpool replacement element is also compatible with Kenmore, Maytag, Amana and Whirlpool brands.

Do-It-Yourself Stories from Customers like You No heat Dan R. • Woodruff , SC • November 30, 2018

First ran the built-in diagnostic tests. Got error code indicating that the inlet thermistor was open. Removed lower access panel and did continuity checks on the inlet thermistor, thermal cutoff and heating element. Even doing these checks is very difficult on this model due to the location of these parts and the limited access through the so-called access panel. But was able to get an open reading on the heating element, so I knew that at least that part was faulty. Could not get a reliable... Read more

$91.33

Compare At:: $108.68
You Save:: $17.35

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Samsung part

Dryer Heating Element Assembly

4.9 (470)

By: Samsung

Part Number: DC97-14486A

The Dryer Heating Element Assembly is essential for ensuring your Samsung dryer heats effectively and dries your clothes efficiently. This high-quality assembly replaces faulty or damaged heating elements, restoring optimal performance to your appliance. Crafted as a genuine OEM part, it guarantees compatibility with a wide range of Samsung dryer models, ensuring a precise fit and reliable operation. Installation is straightforward, allowing you to quickly get your dryer back to working condition without hassle. By choosing this Dryer Heating Element Assembly, you benefit from consistent drying results, energy efficiency, and the longevity of your dryer. If your dryer is experiencing insufficient heat or failing to dry clothes properly, this genuine OEM part is the ideal solution to enhance your dryerGÇÖs functionality and extend its lifespan.

This part fixes the following symptoms

Too hot
Takes too long to dry
Doesn't shut off
tripping breaker

Do-It-Yourself Stories from Customers like You Samsung dryer not producing any heat Maria D. • Niceville , FL • November 12, 2019

This has been posted on my Facebook (but can't tag AppliancePartsPros) titled "As My Husband Slept!" =( Each dash represents a caption in each post. - Nice try taking a few days off! Your vacation days, or hours, are numbered ?? - Step 1: Removed 2 screws from the back. So far so good! - (after removing the top of the dryer) Wow! I'm so proud of myself ????? - (after the front panel was removed) Step 2: Remove the front panel as instructed by the guy on the video ?? ... I think I'm going to be... Read more

$233.66

Compare At:: $280.39
You Save:: $46.73

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Bake Element

4.9 (504)

By: Ge

Part Number: WB44T10011

The Bake Element is an OEM part for GE ovens, designed to provide the heat necessary for baking. This element is located at the bottom of the oven cavity and heats up when electricity is applied, converting electrical energy into heat to cook food evenly.

Over time, however, the bake element can wear out or become damaged.

Symptoms of a bad Bake Element include:

Visible signs of wear or damage, such as blistering, cracks, or breaks in the element.
A burnt out element that no longer glows red or heats up.
Food not baking evenly or thoroughly.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly
Won't start
Element will not heat

Do-It-Yourself Stories from Customers like You Oven bake element malfunction Fred H. • Dacula , GA • March 19, 2014

Watched AppliancePartsPros.com instruction video. Ordered new oven bake element, which arrived a couple days later. Removed old oven bake elelment. Installed new oven bake element. I am very appreciative of the instructional video. It's a very handy way for me to figure out if it's a do-it-yourself repair or not. In this case, another key thing it pointed out was the fact that the two wires that attach to the oven bake element have a tendency to slip back into the insulation behind the... Read more

$53.80

Compare At:: $83.29
You Save:: $29.49

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Bake Element

4.9 (252)

By: Ge

Part Number: WB30X46987

The Bake Element is an OEM replacement part for GE electric ranges. It is the internal heating element located at the bottom of the oven cavity that provides heat for baking and convection cooking functions. This heating element measures 17 1/2 x 18 1/2 inches.

Causes of a bad bake element include failure due to normal wear and tear over extended use. Exposure to spills or splatters inside the oven can potentially damage heating coils or insulators.

Symptoms of a bad bake element are:

Inconsistent or uneven baking temperatures
Element does not heat up or turns red but puts out no heat
Buzzing/humming sounds from beneath oven cavity
Failure of oven to operate or preheat as expected

This OEM part is also compatible with ranges sold under the Hotpoint, RCA and some Kenmore brands.

Do-It-Yourself Stories from Customers like You Ge cafe gas range electric oven would not heat over @ 200f in bake mode John T. • Charlotte , NC • December 26, 2025

Visually inspected bottom heating element and found that it had failed. There was a @2" gap of missing element and burned debris below the damaged area. This was discovered 3 days before Christmas. 1. Open under oven storage drawer and look on the left inside frame frame for Model ID and Serial No. 2. Search on AppliancePartsPro.com for bottom heating element. 3. Ordered part on Sunday evening before Wednedsay Christmas - with expedited next day delivery. 4. Received order confirmation and... Read more

$92.95

Compare At:: $110.61
You Save:: $17.66

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Oven Bake Element

4.9 (448)

By: Ge

Part Number: WB44T10010

The Oven Bake Element is an OEM replacement part for GE ovens. It is a crucial component that generates the heat necessary for baking and roasting functions within the oven cavity.

Dimensions:

18" side to side 19.50" from the mounting bracket to the back
2-3/4" between terminal centers
3" from the terminal to the back plate (calrod bent at a 45-degree angle)
Male Spade 1/4" terminals

Symptoms of a bad oven bake element include:

Uneven heating or hot/cold spots within the oven
Oven taking longer than usual to reach the desired temperature
Element glowing irregularly or not at all during the baking cycle

Causes of a bad bake element can range from simply burning out due to repeated use over time to physical damage caused by drips, spills, or impact.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly
Won't start

Do-It-Yourself Stories from Customers like You The radiant elements had been dead for years the bake element failed spectacularly on Thanksgiving Christine W. • Golden Valley , MN • December 04, 2020

It took a few of us. One to vacuum up the fire extinguisher residue. One to trip the breaker. One to provide light. One to clean out under the stove while it was pulled out. I disconnected the bake element. I needed help to disconnect one of them because it was very tight. I put the element into the oven and reconnected the right side, very easy. The left side fell back into the slot. Curses ensued. I removed the back plate and it was very easy to thread the left wire back into the oven and... Read more

$58.45

Compare At:: $91.24
You Save:: $32.79

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Oven Bake Element

4.9 (714)

By: Ge

Part Number: WB44X200

The Oven Baking Element is an OEM part for GE electric ranges and wall ovens. This baking element is located at the bottom of the oven cavity and provides heat from below during baking function. Even, consistent heating is vital for optimal cooking performance.

Causes of a bad baking element can include mineral buildup from repeated high temperature use that interferes with heating ability. Element coils breaking or blowing out is also common after several years of use.

Symptoms of a bad baking element include:

Inconsistent or inadequate heating from the bottom of the oven
Cook times longer than normal for many recipes
Error codes indicating issues with the lower heating element
Open or shorted element coils preventing any heating

This OEM GE replacement is also compatible with Hotpoint, RCA, and some Kenmore electric wall oven models.

This part fixes the following symptoms

Oven is too hot
Little to no heat when baking
Oven not heating evenly
Element will not heat

Do-It-Yourself Stories from Customers like You Broiler element burnt out on very old oven Deloris B. • Spokane , WA • November 23, 2015

I cannot not sing the praises of this company & their helpful & fast service. I am going to post the online site address w/my praises on my facebook page for my friends that live on ranches many miles from appliance repair shops & towns. The Oven in our house is for sure over 20 yrs old it was in this home when we bought it, the home is 33 yrs old & the Oven is a Wall Oven, there is not room for a standard Oven in this Kitchen. The Oven itself still looks very nice. About 8 yrs ago or more... Read more

$30.60

Compare At:: $68.17
You Save:: $37.57

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Oven Bake Element

5.0 (197)

By: Whirlpool

Part Number: WPW10308477

The Oven Bake Element is an OEM part for Whirlpool ovens. It is a component responsible for providing the heat necessary for baking and cooking. This element is located at the bottom of the oven and heats up when electricity is applied, allowing for consistent cooking temperatures.

Symptoms of a bad Oven Bake Element include:

Uneven baking results or undercooked food
Lack of heat generation even though the oven is turned on
Visible damage to the element such as blistering, cracks, or breaks

Causes of a bad element can stem from natural wear and tear, excessive cooking temperatures overextending the element's capacity, or electrical issues causing the element to fail prematurely.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly
Element will not heat

Do-It-Yourself Stories from Customers like You My electric oven would not fully heat up Richard Z. • Avon , MN • December 20, 2014

The first thing I did was call appliance pros. The tec told me it was a good chance it was the thermostat. He told how to test it with my ohm meter and what range it should be in. I pulled it out and tested it, which was out of the limits he told me it should be in. So I ordered the part. When it arrived in two days, I installed it. The oven now works perfect. Thank you so much. I was just about to go spend $800 on a new oven, and instead fixed it for $75. Awesome website. It was... Read more

$48.95

Compare At:: $57.76
You Save:: $8.81

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Heating Element

4.8 (51)

By: Ge

Part Number: WD05X30818

The Heating Element is an OEM part for GE dishwashers. It is responsible for heating the water during the wash cycles and for drying the dishes after the rinse cycle. Proper functioning of the heating element ensures optimal cleaning and drying performance.

Causes of a bad heating element can include mineral buildup from hard water, electrical faults, or general wear and tear over time. Damage to the heating coil or connections can also impair its functionality.

Symptoms of a bad heating element include:

Dishes not drying properly
Dishwasher cycles taking longer than usual
Water not heating during the wash cycle
Error codes related to heating issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Do-It-Yourself Stories from Customers like You Dishwasher was not heating water and dishes were coming out wet and cold no steam at all James C. • Lubbock , TX • February 15, 2019

I followed the directions on several websites for repairs. The obvious place to start is the heating coil and thermostat. I checked the continuity of the coil and it was good with a reading of almost zero resistance. Next I read that there is no thermostat controls on my GE dishwasher so I followed another webpage that said the Sensor Turbidity Assembly acts like a thermostat so I replaced that. Wasted effort as that switch sensor was OK. Normally it has a light on when it is working, a... Read more

$43.31

Compare At:: $51.97
You Save:: $8.66

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Oven Bake Element

4.9 (531)

By: Whirlpool

Part Number: WP308180

The Oven Bake Element is an OEM part for Whirlpool ovens. This part heats the oven's interior during the baking process. Located at the bottom of the oven, the bake element heats up when electricity passes through it, allowing for consistent and even cooking.

Causes of damage to the Oven Bake Element can include normal wear and tear from regular use, a buildup of food debris causing hot spots and potential burns out, or electrical issues leading to shorts or surges that damage the element.

Symptoms of a bad Oven Bake Element include:

Visible signs of damage to the element, such as blistering, holes, or breaks in the element itself.
The oven failing to heat up at all
A lack of visible glowing from the element during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly
Oven is too hot
Won't start

Do-It-Yourself Stories from Customers like You Heating element lower broke creating a direct ground fault to the oven wall and resulted a flash of bright fire Stanley B. • Chula Vista , CA • June 16, 2017

My wife was using the oven and she shouted "emergency, oven fire" as i was half asleep in the reclining chair (I will be 86 in Oct.) As I dashed, well not quite, into the kitchen mentioning the fire extinguisher, she exclaimed "no, electrical fire, throw the circuit breaker"....which I very promptly did and the fire was no more; just a lot of bad odor. Removing the severed 32 year old bake oven element was somewhat delayed due to corrosion of the element mounting screws and electrical... Read more

$40.95

Compare At:: $71.72
You Save:: $30.77

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Frigidaire part

Dryer Heating Element Assembly

4.9 (428)

By: Frigidaire

Part Number: 131553900

The Heating Element Assembly is an OEM replacement part for Frigidaire dryers that is responsible for generating the heat necessary for drying clothes. This assembly converts electrical energy into heat and creates the warm air that circulates within the drum to dry clothes efficiently.

Symptoms of a bad Dryer Heating Element Assembly include:
Clothes remain damp after a full drying cycle.
The dryer takes longer than usual to dry clothes.
No heat is produced, resulting in cold air circulating within the drum.

Causes of failure can include overuse, a surge in electrical power, or lint buildup causing overheating and damage to the components.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Includes rear housing with the element and insulators already attached. For the element only order 5300622034. For the insulators order 131472100.

This part fixes the following symptoms

No heat or not enough heat

Do-It-Yourself Stories from Customers like You Constant beeping no heat Amy N. • Pike Road , AL • March 27, 2018

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

$117.95

Compare At:: $140.36
You Save:: $22.41

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Heating Element Replacement Parts

There's nothing quite like a dependable appliance, and when it comes to keeping your dryer or oven running smoothly, having access to top-quality heating element replacement parts is essential. These crucial components ensure your appliance reaches the necessary temperatures for drying clothes or cooking meals efficiently.

Heating elements play a pivotal role in various appliances by providing the necessary heat to get the job done. Whether it's your oven baking a delicious batch of cookies or your dryer fluffing up a fresh load of laundry, the heating element is at the heart of the action. High-quality heating element parts not only ensure optimal performance but also help extend the overall life of your appliance.

Original Equipment Manufacturer (OEM) replacement parts are particularly noteworthy. Known for their quality and compatibility, OEM heating elements are designed to fit perfectly and function seamlessly with your appliance, offering a reliable solution when you need it most.

Trust heating element replacement parts to keep your ovens baking and dryers drying, just like new.

Appliance

Appliance

Lawn & Garden

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Heating Element

Dryer Heating Element

Why this heating element?

Fixes these common dryer problems

DIY install — about 20 minutes

Bake Element

Dryer Heating Element

Bake Element

Dishwasher Heating Element

Oven Bake Element

Dryer Heating Element

Dryer Heating Element Assembly

Bake Element

Bake Element

Oven Bake Element

Oven Bake Element

Oven Bake Element

Heating Element

Oven Bake Element

Dryer Heating Element Assembly

Appliance Type

Brands