Kenmore / Sears Hose Or Tube

This is the dishwasher manifold tube only. It attaches to the bottom of the upper rack. For the complete kit order 675808. Also consider checking the mount that attaches this manifold tube to the dishrack. For the mount order WP8539324.

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This is a replacement ice maker fill tube. This is a genuine OEM part made by LG and has been sourced directly from the manufacturer. This part is intended to replace broken or detached ice maker fill tubes in a variety of refrigerators. This piece of plastic tubing supplies the in-built refrigerator ice maker with water so it can make ice. If the ice maker is not working properly and is not making ice, there may be an issue with the tubing. Always make sure that the refrigerator is entirely disconnected from power and water before starting the any repair work. Please ensure that the appropriate safety precautions are followed when attempting to fix any appliances. For more accurate information on how and where to install this ice maker fill tube, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this ice maker fill tube is suitable for use on several different models of refrigerators manufactured by LG and Kenmore. This is a genuine part made of high-quality, durable plastic and is sold individually.

This fill and drain hose assembly connects a portable dishwasher to a sink faucet, delivering incoming water and routing wastewater back to the sink. Replacing a worn assembly restores a secure connection and helps prevent leaks during operation.

• Integrates inlet and drain hoses with a faucet coupler for quick, tool-free hookup
• Supplies water to the dishwasher and returns drain water to the sink
• Can address no fill or no drain symptoms caused by a damaged or obstructed hose/coupler

• Safety first: Unplug the dishwasher and turn off water before servicing
• Expect residual water; place towels/pan and relieve line pressure
• Ensure a compatible faucet adapter is installed; attach the coupler fully and verify a good seal
• Route hoses without kinks, secure the drain end to the sink, and check for leaks on first run

This replacement hose routes water within your washer. Replacing a cracked, worn, or leaking hose restores a secure, watertight path so the machine can move water properly without puddles or performance issues.

• Transfers water between internal components during wash cycles
• Maintains a sealed flow path to help prevent leaks
• Damage may present as water on the floor, moisture under the unit, or related fill/drain errors
• Cracks, swelling, abrasion, or loose connections are common failure signs

• Unplug the washer and turn off water supply; have towels or a pan ready for residual water
• Note hose routing and clamp positions before removal; photos can help
• Transfer or replace clamps as needed; seat connections fully and secure firmly
• Run a test cycle and check all connections for leaks

This inlet hose channels household water to the appliance's fill system. Replacing a worn or leaking hose restores proper water flow and helps protect floors and internal components from water damage.

• Directs water from the household supply to the unit's inlet/fill assembly
• Maintains a watertight path to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or mineral-fouled
• Common symptoms: leaks at fittings or beneath the unit, slow or no fill, intermittent filling, or water-related error messages

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure slowly
• Route the hose without kinks; ensure sealing surfaces and/or washers are clean and properly seated
• Secure connections per the OEM design (compression fitting or clamp); restore water and check carefully for leaks on the first run

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

This water tube connector joins sections of your refrigerator's water line for the dispenser and ice maker. It restores a secure, leak-resistant connection when the original coupling is damaged or leaking.

• Connects two segments of refrigerator water tubing
• Helps maintain proper water flow to dispenser and ice maker
• Resolves leaks caused by a cracked, worn, or loose connector
• Useful when replacing or rerouting water lines during service

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Cut tubing square and insert fully until seated; tug gently to confirm a secure fit
• Restore water and check all connections for leaks; replace any damaged tubing as needed

This collar kit renews the quick-connect faucet interface on select portable appliances, restoring a secure, leak-resistant connection at the sink. Replace a stripped, cracked, or missing collar to stop drips and ensure the coupler attaches smoothly.

• Provides the correct shoulder/threads for the quick-connect coupler or adapter
• Helps seal the faucet connection to reduce leaks and spray
• Replaces worn, damaged, or missing collar in the connector assembly
• Common symptoms: leaking at the faucet, coupler won't latch or pops off, loose connection

• Turn off water and disconnect the appliance from the faucet before service
• Relieve hose pressure and place a towel under the work area
• Remove the existing collar and clean faucet threads before installing the new one
• Hand-tighten only; avoid overtightening and check for leaks on first use

This mechanical tube connector joins sections of your refrigerator's water tubing. Use it to restore a secure, leak-resistant connection when repairing or replacing lines that feed the dispenser, ice maker, or filter. What it does:

• Connects two sections of the refrigerator's water tubing
• Helps stop leaks caused by a cracked, loose, or damaged connector
• Can restore water flow when a line has separated at a coupling
• Provides a serviceable coupling point after replacing a tubing section

• 1 mechanical tube connector

• Unplug the refrigerator and shut off the water supply before servicing.
• Cut tubing ends square; remove any damaged section and ensure clean, burr-free ends.
• Fully insert tubing into the connector and perform a gentle pull test to verify engagement.
• Turn water back on and inspect all connections for leaks before restoring power.

This adjustable manifold connects the upper rack to the dishwasher's rear water feed. It channels wash water to the upper spray arm and maintains a sealed connection as the rack height changes for consistent cleaning performance. What it does:

• Routes water from the rear feed tube to the upper/middle spray arm
• Self-adjusts with rack position to keep a secure, leak-resistant connection
• Replace if cracked, deformed, or the coupling no longer seals
• Common symptoms include poor cleaning on the upper rack, weak spray, upper spray arm not turning, or a small leak at the back of the tub

• 1 adjustable manifold

• Disconnect power and shut off water; wear gloves for protection
• Remove the upper rack by releasing the rail end caps and sliding the rack out
• Unclip the manifold from the rack and disengage it from the rear feed port; seat the new manifold fully
• Reinstall the rack and ensure the spray arm spins freely

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

This water tube routes water between internal components in your appliance to support proper filling and dispensing. Replacing a brittle, cracked, or kinked tube restores reliable flow and helps prevent leaks and water damage. What it does:

• Provides a sealed path for water from the valve to the component it serves
• Helps maintain correct flow by avoiding kinks and restrictions
• Over time, tubing can harden, crack, or deform from heat and age
• Common symptoms: visible leaks or puddling, slow/erratic flow, or no water to the function it serves

• 1 water tube

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure
• Note the original routing and connection points; take a photo for reference
• Fully seat the tube in quick-connect/compression fittings and check for leaks after restoring water

12 Ft in length