Kenmore / Sears Hose Or Tube

These inserts are for 1/4 inch plastic tubing. Package of 4.

This drain hose channels used water from the appliance's drain pump to the household plumbing. Replacing a cracked, kinked, or clogged hose stops leaks and helps your unit drain correctly at the end of the cycle.

• Directs wastewater from the drain pump to the home drain system
• Helps maintain proper outflow during the drain portion of the cycle
• Common symptoms: standing water after a cycle, water on the floor, drain error codes, visible cracks or kinks in the hose
• Old hoses can become brittle, split, or obstructed over time

• Disconnect power; shut off water supply if applicable
• Place towels or a pan to catch residual water when removing the old hose
• Note original routing; install the new hose without sharp bends or kinks and secure all connections with existing clamps or appropriate replacements
• Run a test drain/cycle and check every connection for leaks

This inlet hose supplies household water to the appliance's fill system. Replace a worn, kinked, or cracked hose to restore normal water flow and help prevent leaks that can lead to poor performance or damage. What it does:

• Connects the home water supply to the unit's inlet/fill connection
• Provides a sealed pathway for water during operation
• Helps maintain consistent water flow to the appliance
• Common symptoms: leaks at fittings, slow or no fill, visible kinks, bulges, or cracks

• Includes: One inlet hose

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve any line pressure
• Hand-thread fittings to avoid cross-threading, then tighten snugly—do not overtighten
• Restore water, check all connections for leaks, and test operation

Water tube connector that joins two sections of a refrigerator's water tubing for a secure, leak-resistant connection. Replacing a cracked or leaking connector can help restore consistent water flow to the dispenser and ice maker.

• Connects two lengths of refrigerator water tubing in the supply, filter, dispenser, or ice maker circuit
• Helps maintain a sealed connection to reduce leaks and air intrusion
• Common symptoms of failure: dripping at the fitting, water under the unit, weak/no dispensing, or ice maker not filling
• Replace if the connector is cracked or will not hold tubing securely

• Unplug the refrigerator and shut off the water supply
• Dispense water to relieve line pressure; place a towel under the connection
• Cut tube ends square; push each tube fully into the connector until seated, then tug gently to confirm engagement
• Restore water and check carefully for leaks before reconnecting power

This water fill tube directs water from the inlet valve into the ice maker's fill cup. Replace a cracked, kinked, or frozen tube to restore reliable ice production and help prevent leaks or splashing inside the freezer.

• Routes water from the rear inlet valve to the ice maker fill area
• A damaged or blocked tube can cause no ice, small cubes, leaks near the back/freezer, or ice buildup at the fill spout
• Formed design helps aim water into the fill cup for proper filling
• Replace if the tube is cracked, brittle, kinked, or repeatedly freezing

• Disconnect power and shut off the water supply before servicing
• Access the rear and freezer liner; disconnect the old tube at the valve and liner/fill area
• Seat the new tube fully through the liner and into the ice maker fill cup; reconnect to the valve and secure any reused clips/seals
• Restore water and power, then check for proper fill and leaks

This faucet adapter threads onto a compatible sink faucet to provide the connection point for an appliance's quick-connect hose, creating a secure, watertight hookup during filling and operation. What it does:

• Adapts faucet spout threads to accept the appliance hose/coupler
• Helps prevent leaks and drips at the faucet connection
• Replaces a worn, stripped, or missing adapter
• Common fix when a quick-connect hose (e.g., on a portable appliance) won't attach or pops off

• 1 faucet adapter

• Turn off water and remove the existing faucet aerator before installing
• Hand-thread the adapter carefully to avoid cross-threading; snug gently if needed with a non-marring tool
• Attach the hose/coupler and slowly open the faucet; check for leaks and retighten if necessary

This drain tube directs defrost/condensate water from the appliance's drain outlet into the drain pan, helping prevent water from pooling inside the cabinet or leaking onto the floor for reliable, mess-free operation. What it does:

• Channels defrost/condensate water from the drain outlet to the pan
• Helps prevent interior leaks, puddles beneath the unit, and ice at the drain
• Restores proper drainage when the original tube is cracked, misshapen, or clogged
• Addresses symptoms like water under drawers/shelves or musty odors from standing water

• 1 drain tube

• Disconnect power and pull the unit forward for rear access; turn off water supply if applicable
• Remove the old tube and clear any debris/ice from the drain opening
• Fully seat the new tube on the drain outlet and position the outlet over the pan, following original routing
• Test by pouring a small amount of warm water into the drain to ensure proper flow and no leaks

The Drain Hose is an OEM part for Whirlpool dishwashers. This hose works to divert wastewater from the dishwasher to the garbage disposal or drain pipe beneath the kitchen sink.

The drain hose is responsible for safely transporting soapy water, food debris and other particles away from the washing cavity during each cycle. It prevents leaks and backup within the dishwasher tub.

Causes of a bad drain hose can include cracks, splitting, or deterioration of the plastic tubing over many years of use. Clogs within the hose are also problematic.

Symptoms of a failed drain hose include:

• Puddles or leaks developing beneath the dishwasher
• Inability to fully drain wash and rinse water after cycles
• Fault codes showing drainage issues

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement water tube routes water within the refrigerator's internal water system. Installing a fresh, intact tube helps stop leaks and restores reliable water flow to the dispenser and ice maker. What it does:

• Carries water between components such as the inlet valve, reservoir, dispenser, and ice maker
• Maintains a sealed, kink-free path for proper flow and pressure
• Common signs of failure: leaks or puddling, weak or no dispenser flow, ice maker not filling, brittle or discolored tubing

• One tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the original routing; take photos to match length and path
• If trimming, cut ends square and fully seat into the existing push-to-connect or compression fittings
• Restore water and check all connections for leaks before powering the unit back on

Includes connector and both clamps.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

Inlet valve to icemaker

Replacement water tube that routes water from the inlet valve to the refrigerator dispenser and ice maker, helping restore proper water flow for reliable dispensing and ice production. What it does:

• Carries water from the refrigerator inlet/valve to the dispenser and ice maker fill system.
• Used when cracked, kinked, clogged or brittle tubing prevents water flow.
• Helps stop leaks and restore normal ice maker fill when tubing is damaged.
• Addresses symptoms such as no water at the dispenser, ice maker not filling, or visible leaking under the fridge.

• Turn off the water supply and unplug the refrigerator before beginning any work.
• May require basic hand tools and careful routing to avoid kinks; do not overtighten fittings.
• Inspect and replace any damaged clamps or seals; test for leaks after reconnecting the water supply.

This replacement hose restores a secure, leak-resistant path for air or condensate in your appliance. Replacing a cracked, kinked, or brittle hose helps maintain proper flow, prevents leaks, and supports overall performance.

• Channels air or water as designed to ventilate or drain the unit
• Helps maintain a sealed connection at fittings to minimize leaks
• Flexible design supports correct routing without sharp kinks
• Common symptoms: visible cracks or brittleness, kinks, leaks, poor draining or reduced airflow

• Disconnect power and, if applicable, shut off water before servicing; allow components to cool.
• Place towels/containers to catch residual water; wear gloves to protect from sharp edges.
• Transfer and reuse existing clamps/adapters if required; replace any worn seals or clamps.
• Route without sharp bends; fully seat and secure both ends; test for leaks or airflow after installation.

Contains two, six foot long braided hoses with 90 degree ends.