Kenmore / Sears Parts

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Adjustable leveling leg with foot pad for dryers, washers, and pedestals. Replace cracked, broken, or missing legs to stabilize your appliance.

Adjustable leveling leg threads into dishwasher base to support and stabilize the unit. Replace worn, missing, or broken feet to restore proper leveling.

Leveling leg for washers. Installs at the base to support and level your machine. Replace if cracked, broken, worn, or missing for proper stability.

Adjustable leveling leg threads into washer base to stabilize and level the cabinet. Replace worn, missing, or broken legs to prevent rocking and vibration.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Adjustable leveling leg that supports and stabilizes your dishwasher under counters. Replace if cracked, stripped, or unable to hold level position.

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

This drum support roller keeps the dryer drum turning smoothly and quietly by supporting the drum's weight and reducing friction. Replacing a worn roller restores proper drum alignment and reduces noise and rubbing. What it does

• Supports the dryer drum to maintain smooth rotation and proper clearance
• Reduces grinding, thumping, or rumbling noises caused by worn rollers
• Prevents drum wobble and uneven wear on the drum and seals
• Helps the drum spin freely for consistent drying performance

• One replacement roller

• Disconnect power (and gas supply if applicable) before beginning any repair
• Access typically requires removing the dryer's rear panel or front assembly; follow your model's service manual
• Inspect the mating shaft and adjacent roller(s); replace matching rollers if also worn
• Use appropriate tools and avoid forcing parts

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

Replacement cabinet roller wheel for refrigerators. Installs on the bottom of the cabinet to restore smooth rolling movement. Replace if cracked, worn, or broken.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Rear mobility wheel mounts to the back base of your refrigerator. Replace if worn, cracked, or causing uneven rolling when moving the unit for cleaning.

This replacement drum support roller helps the dryer drum turn smoothly and reduces noise from worn or seized rollers. Restores proper drum alignment for more reliable drying and quieter operation. What it does:

• Supports the dryer drum and allows it to rotate on a stable axle
• Reduces squealing, grinding, or scraping noises caused by worn rollers
• Prevents drum wobble and uneven wear that can lead to fabric damage or belt stress
• Helps maintain proper drum alignment to improve drying performance

• Disconnect power before servicing and ensure the dryer is fully powered off.
• Access may require removing the dryer back panel or front bulkhead; support the drum while replacing the roller.
• Inspect adjacent parts (shaft, felt seals, idler, belt) and replace if worn to avoid repeat failures.
• Tighten fasteners securely but avoid over-torquing; test drum rotation by hand before reassembly.

Replace a broken or worn caster wheel on your dryer. This kit includes one rolling caster and washers for stable support and easy movement across floors.