Kenmore / Sears Range Parts

• Little to no heat when broiling
• Element will not heat

I ordered the replacement part; after it arrived, I turned off the power to the oven - watched the video on how to replace the part, which was fantastic as it told me to make sure when I disconnect the old element not to let the wires fall behind the oven (that would have been a big problem b/c it's a wall oven) - However, one wire still slipped back a little - so I used needle nose pliers to retrieve it. Was able to plug the new one in - screw it into place with the original screws. I made... Read more

Order the part from you all. Watched the video how to install, which was easy to understand. the part arrived A DAY EARLIER than we expected! How nice is that? and installed part, stove /oven works. everybody's happy. Read more

The previous tenant in my daughter's new apartment apparently had a grease fire of sorts in the GE XL44 gas oven. This left the insulating double glass panes so fouled up that one could not see into the oven. I removed the oven door (just lifts off the hinges) and proceeded to disassemble the door so as to get to the glass panes. That's when the real problems arose: the window seal rope, which lays around the edge of the opening to the oven, was burnt to a crisp -- see photos. The oven... Read more

Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more

Replaced the oven igniter Whirlpool Part Number WPW10324738. Read more

Looked up the part number at Appliance Part Pros, ordered the window pack (received it the next day), and replaced the glass assembly. Was generally able to follow illustrated parts breakdown as a guide. Read more

It was a Friday afternoon, of course, I went to my local supply house for the part. I did look it up on your site first to see what I needed and how much I was looking to pay. I got there and "They don't stock those!" I said thank you and went to do more hunting. I ended up at what I found to be the only other parts place in town, and they could've ordered it, for much more than you, I don't mind paying more to get it now but am not going to wait a week to pay more. I said no and came home,... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

I removed all the individual burners so I could lift the stainless cover to expose the igniter wires. I cleaned all the wire connections and the 4 good igniters and replaced the one bad igniter. Reassembly was easy and everything worked properly when done. Video of repair was helpful and all parts ordered were correct and shipped promptly and I will definitely use AppliancePartsPros again. Read more

Removed damage terminal block ordered new block on line. when I received new block installed it stove works fine easy to replace. If I had not been home at the time when this happen it may had cause a big house fire. Read more

• Element will not heat
• Won't start

Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start

The repair was relatively simple and quick. The only part required was a new oven thermostat assembly and the tools I used for my model was a flathead screwdriver, cross-point screwdriver, torque bit and 1/4 inch socket using a bit driver. To complete the repair, I did the following: 1. Remove all top stove burner pieces and place to the side. Remove the 3 three screws (torque bit) in each of the 4 burner locations. That will allow the top lid to separate from the main unit later. 2. Pull... Read more

Ordered parts ( very easy) and replaced old ones . Pop out, pop in. Simple but it made my stove and oven new again. Read more

It was a Friday afternoon, of course, I went to my local supply house for the part. I did look it up on your site first to see what I needed and how much I was looking to pay. I got there and "They don't stock those!" I said thank you and went to do more hunting. I ended up at what I found to be the only other parts place in town, and they could've ordered it, for much more than you, I don't mind paying more to get it now but am not going to wait a week to pay more. I said no and came home,... Read more

• Element will not heat
• Won't start
• Gas igniter glows, but will not light

Replaced ignitor. Read more

Watched the video here, took the leap that burner was the problem and ordered it. Also found another vid on you tube that was more specific to my Kenmore. Tip: find out how to take off the oven door. For mine it was very easy but not detailed in the APP vid. I followed instructions in APP vid but also first took off back panel of range and tested resistance of old burner to ensure that was truly the problem (as suggested by other YT vid). Also, dis/connecting the wires from the back is easier... Read more