Need Help?
Call
Components that help remove ice cubes from the ice maker mold and direct them into the storage bin. Replace if ice cubes aren't ejecting properly, get stuck in the mold, or if the ice maker produces malformed ice.
My fridge was too cold - everything was freezing solid, even in the produce bins. The air from the diffuser vent was constantly running. After unplugging the fridge and plugging it back in, the diagnostic code on the control panel indicated that the air diffuser was not working. I purchased a new air diffuser, watched the very helpful video that showed how to install it, and replaced the part in about 10 minutes. The next day, I can tell that everything in my fridge has finally begun to thaw... Read more
This is the complete horizontal ice dispenser bucket assembly with crusher. It fits 22 cubic foot refrigerator models. For 20 cubic foot models order WP2209778. For 25 and 27 cubic foot models order WPW10312300.
I ordered the complete assembly ice bucket and all Read more
The ice maker and auger motor assembly powers the mechanisms that produce ice and push it from the storage bin through the dispenser chute. Without a functioning motor, the ice maker will stop producing ice and the auger will no longer move ice to the dispenser. Replace this assembly if your ice maker has stopped making ice, the dispenser is not dispensing ice, or you hear a humming or grinding noise from the ice bin area.
The new icemaker was a perfect fix. Read more
Ice not dispensing or only partially crushing? The ice dispenser auger moves ice from bin to chute. DIY-friendly repair, typically 30 minutes.
Had to replace the auger. The auger on my ice maker was made of plastic and had broken pieces off it. The new one is made of metal and seems to work much better. Was a fairly simple repair. However pay close attention when disassembling, I recommend using your cell phone and snap a pic of the different stages as I became a little confused when putting it back together. Ordered the part and it was here the next day. I'm very happy to have my ice coming down the chute again. By the way, I'm a 70... Read more
Ice won't dispense or jams in chute? Cracked bin or broken auger blades stop ice flow. This ice bin assembly restores dispensing. Easy DIY, no tools.
Replaced ice bin assy. Read more
Ice won't dispense or auger jammed? This end cap secures the auger shaft and blade stack in the ice bin. Simple 5-minute DIY repair restores dispensing.
Removed old cap replace with new 5 min. works like new received new part in 2 days Read more
Ice dispenser not working or making loud grinding noise? This ice auger and crusher blade assembly is often the fix. Simple 5-minute DIY repair.
Replaced both parts Read more
Ice not dispensing or slow ice flow? This ice bucket and auger assembly stores and moves ice to your dispenser. Simple DIY install in 10-30 minutes.
I ordered a new bucket and auger combination--I didn't want to have to completely disassemble the mechanism to replace the rusted auger helix dispenser, so for about twice the cost of the auger alone I got the complete assembly. The product arrived in pristine condition less than 48 hours after I purchased it online. About 10 minutes later (most of that spent taking out the old bucket and finding my philips head screwdriver), I had removed the four screws holding the cover plate on the old... Read more
Ice not dispensing or auger won't turn? The drive bar transfers motor rotation to crush and dispense ice. Moderate DIY repair with video guide.
My problem started with a rusting condition in the ice bin that spiraled out of hand. I took apart the ice bin and all the hardware thinking I could clean it with the suggested baking powder. Plastic parts cleaned up like new, metal parts were pitted. I wire brushed and sanded the parts put it all back together and gave it a try. All appeared fine then two days later the ice dispenser stopped. I watched a couple of videos and most pointed to the ice auger motor. One video specifically said you... Read more
Ice maker overflowing or not stopping? This shut-off arm extension clips onto the bail arm to help the bin detect when full. Simple 5-minute fix.
Purchased Appliance Parts Pros replacement ice maker, removed the defective unit, matched the proper wiring harness using the wiring color codes at the P and J side connectors. Approximately 1 hour following the installation, I delightfully heard the first set of cubes ! Read more
Ice won't dispense or motor hums without dispensing? A faulty ice container bin often causes these issues. Simple replacement restores ice dispensing.
I ordered a complete new bin with everything in it attached already. All I had to do was wash it and set it in the compartment on freezer door. Within a couple hours, I had ice again. Easy fix. Read more
Ice dispenser jammed or grinding? A cracked baffle prevents smooth ice flow. This support aligns the auger inside the bin. Moderate DIY with video guide.
I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again. Read more
Ice won't dispense or gets jammed? This ice bucket assembly stores and feeds ice to your dispenser. Restores smooth dispensing in about 20 minutes.
I ordered part from appliance parts and it was perfect fit. Read more
Ice maker stopped producing ice? This refrigerator ice maker assembly restores ice production. DIY-friendly installation takes about 15 minutes.
We had a sears tech come out and "inspect" our freezer - he said it was one of the 2 vales behind the fridge that needed to be replaced. I found them for 50 bucks each on amazon... but then I thought I might shop around. Then i found this kit - that has the 2 valves AND the icemaker assembly for basically the same price. I went ahead and swapped out the icemaker assembly since it didn't involve getting behind the fridge. the next morning - BOOM ice. lots of ice. amazed. and happy. Read more
Ice won't dispense or bin tips forward? Replace your worn upper ice bin to fix jamming, spillage, and broken mounting prongs. Easy DIY with video guide.
Took the broken bin out and put the new bin in. all of maybe two minutes. Read more
Ice maker won't stop making ice or arm keeps falling off? This shut-off arm senses bin levels to control production. Simple snap-in installation.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.