Need Help?
Call
Central hub that connects the inner tub to the drive shaft in washers. Replace if corroded, cracked, or arms have broken off causing wobble or imbalance.
Looked online at several websites to see if I could figure out the problem Came across AppliancePartsPros video on replacing bearings. Watched it a couple of times and determined (well, guessed) it was the bearings and/or spider. Followed the video (great job by the way) and disassembled the washer. The spider was cracked on one arm so ordered a new one from this site. I also ordered two new bearings and the bearing seal b/c learned from the web and local appliance store that they go bad in 7+... Read more
Suspension rod kit for washers. Supports the drum and reduces vibration during wash and spin cycles. Replace when rods are broken, worn, or damaged.
One of the suspension rods was not working so I replaced the bad one and the other three . Tub has now leveled out and is spinning properly without making the noise. Have not needed to replace the pump but will do so if necessary. Thanks to Appliance Parts Pro for their prompt service and quality products. Read more
Stabilizes the washer tub during spin cycles. Replace worn or broken rear shock absorbers to restore smooth operation and prevent drum contact with cabinet.
Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more
Front shock absorber kit stabilizes the washer tub during spin cycles. Replace worn, loose, or broken dampers to restore smooth operation and stability.
I tore it apart using. YouTube videos to guide me and found the shocks were loose and floppy. I found the shocks in stock here and had them in my hand 2 days later for only $10 shipping! It runs great now! Read more
Set of 4 suspension rods that support and steady the wash tub. Replace if rods are worn, broken, or causing excessive vibration during the spin cycle.
I ordered a tub suspendion Kit for it. Read more
Replacement suspension rod kit for washing machines. Includes 4 rods that stabilize the tub during wash and spin cycles. Needed when rods are worn or bent.
Replaces a broken, corroded, or cracked drum spider assembly. This structural support connects the drum to the shaft in front-load washers.
I noticed my 5-year-old Samsung, front-loading washing machine started to sound like my kids were using it as a drum kit. I immediately checked it out and the stainless drum was wobbling so badly that I just took it for an unbalanced load of clothes. My gut was telling me that something was wrong because I had not remembered the machine being so loud before. I removed the clothes from the washer and I ran it empty to confirm my suspicions: the wobble was still there. I would say it had a 2"-3"... Read more
The Shock Absorber Kit is an OEM part for Whirlpool washing machines. This kit includes 4 shock absorbers designed to reduce vibrations and absorb shocks during the washing and spinning cycles, providing stability and minimizing excessive movement of the washer drum.
Causes of a bad shock absorber can include wear and tear from regular use, exposure to heavy loads or unbalanced loads that put excessive strain on the absorbers, or damage due to impact or mishandling.
Symptoms of a bad shock absorber kit include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I tube what could be the cause. Took apart the washer and ordered the parts. Put parts in. Read more
The Strap is an OEM part for Whirlpool washing machines. It is a component located inside the washer tub that holds onto and spins the outer tub during the wash cycle. The strap washer plays an important role in securing the outer tub in place while continuously channeling rotational force to drive the washing action and clean clothes effectively.
Causes of a bad strap can include wear and tear from years of use, damage due to impact or mishandling, or degradation from chemical exposure.
Symptoms of a bad strap include:
This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Suspension rod assembly for washers. Installs to support the drum and absorb vibrations. Replace if worn, damaged, or causing balance issues during spin.
We had a repair man come and tell us the needed repair at the cost of 70.00 I ordered the parts and saved money. Read more
Replace a broken or worn shock absorber that no longer dampens drum movement. Installs between the drum and base to reduce vibration and noise.
Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more
Replaces broken or worn washer shock absorber that controls tub movement during spin. Installs on washer suspension to reduce vibration and shaking.
I took the front panel off which exposed the front two shock absorbers. But I could still only replace the front left shock. I could not get access to the one on the right. I then took the back panel off which gave me access to both back shocks and the other front shock. A simple twist and they were done. The longest part of the job was taking the back panel off. Read more
Includes suspension pads.
Supports and centers the inner tub in front-load washers. Replace if cracked, corroded, or broken to restore proper drum alignment and balance.
Spider arm connects the wash basket to the drive shaft in front-load washers. Replace if cracked, corroded, or broken to restore proper basket support.
Connects the washer's inner drum to the drive assembly. Replace if cracked, damaged, or worn to restore drum stability and eliminate wobbling or noise.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.