Kenmore / Sears Washer Pump

The Drain Pump is an OEM replacement part for Frigidaire front load washers. Located inside the base of the washing machine tub, it actively pumps out water through the drain hose after each cycle completion. Efficient drainage is vital for preventing standing water issues.

Causes of a bad drain pump can include mineral or scale buildup within the pump chamber or impeller over time. The water valve may fail to open fully, blocking drain flow. Bearings may wear, causing the impeller to jam.

Symptoms of a bad drain pump are:

• Incomplete water draining after the cycle
• An accumulation of water remaining in the tub
• Leaking from the base
• Error codes could indicate drainage problems.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore.

The Drain Pump is an OEM part for Whirlpool top-loading washing machines. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle.

The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles.

Symptoms of a faulty drain pump are:

• Remaining water at the bottom of the tub after washing
• Puddles or splashing near the machine during drainage
• Grinding or screeching noises when the pump should be operating

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Pump Casing is an OEM replacement part for LG top-load washing machines. This casing houses the water pump, providing a protective enclosure that shields the pump from debris and external factors. The casing is designed to fit snugly around the pump, helping to maintain its position and function within the washing machine.

Causes of casing failure can include cracks or leaks from repetitive pressure fluctuations exerted during machine operation. Casings experience extensive mechanical stresses.

Symptoms of a compromised casing include:

• Water leaks near or below the pump assembly
• Noisy or grinding pump noises during water fills or drainage
• Error codes related to water flow issues

This casing fits LG top load models as well as some Kenmore configurations. 

The Pump Drain is an OEM part for GE washing machines. This component is responsible for removing water from the washer drum during the drain cycle, ensuring that the water is efficiently expelled from the machine. The pump drain plays a crucial role in the washing machine's ability to complete its cycles and maintain optimal performance.

Over time, the pump drain can become clogged, worn out, or damaged due to regular use or foreign objects obstructing the pump. Common causes of a bad pump drain include buildup of debris, wear and tear on the pump mechanism, or blockages from items accidentally left in pockets.

Symptoms of a bad pump drain include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• The washer stopping mid-cycle due to drainage issues
• Water leaking from the bottom of the washer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Direct Drive Washer Pump is an OEM component specifically designed for Whirlpool brand clothes washers. It works to circulate water inside the washtub during cleaning cycles.

Symptoms of a faulty direct drive pump include:

• Incomplete or insufficient water fills  
• Poor drainage at the end of cycles
• Gurgling or drain issues occurring

Causes involve normal wear over extended usage. Mineral buildup within internal components can decrease pumping effectiveness as well. 

Two large ports with flapper valve. Fits most Whirlpool and Kenmore direct drive washers (no belt models). Related item: Motor coupling 285753A.

Compatible models include some brands produced by Maytag, Jenn-Air, and Kenmore as well.

The Water Pump is an OEM replacement part for Whirlpool washing machines. It plays a crucial role in circulating water throughout the wash cycles and draining the used water from the tub.

Symptoms of a bad water pump include:

• Washer not draining properly, leaving standing water in the tub
• Loud grinding or humming noises during the spin or drain cycles
• Leaks around the pump or connected drain hose
• Error codes or indicators related to drainage or pump issues

Causes of a bad water pump can include clogs or obstructions in the pump impeller, worn-out pump seals or bearings, or electrical malfunctions preventing the pump from operating correctly. Foreign objects or debris can also contribute to pump failure.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Pump Assembly, Drain is an OEM part for LG washing machines. This pump assembly is responsible for removing wastewater from the washer's tub during the drain cycle, ensuring efficient drainage and preparation for subsequent wash cycles.

Causes of a bad drain pump can include wear and tear from regular use, blockages from debris or lint, or electrical failures. A malfunctioning drain pump can lead to improper drainage and water remaining in the tub after the wash cycle.

Symptoms of a bad pump assembly include:

• The washer not draining water properly
• Standing water in the tub after a cycle is complete
• Unusual noises during the drain cycle
• Error codes related to drainage issues

This OEM LG part is also compatible with Sears/Kenmore models.

The Drain Pump Assembly is an OEM part for LG washing machines. This part removes water from the washer's tub during the drain cycle.  

Causes of a bad drain pump assembly can include blockages from debris or small clothing items, wear and tear on the pump motor, or damage to the pump's impeller.  

Symptoms of a bad drain pump assembly include:

• Water not draining from the washer
• Loud or unusual noises during the drain cycle
• Error codes related to drainage issues
• Water leaking from the pump area

This OEM LG part is also compatible with some Kenmore models.

By Frigidaire. 27 inch models, 1990 and up.

This drain pump assembly actively removes water from the washer tub during drain and spin cycles, helping prevent standing water and cycle interruptions. Replacing a worn pump restores proper draining and reliable cycle completion.

• Pumps water from the tub through the drain hose to the household drain
• Common symptoms: no drain or slow draining, water left in tub, cycle stops due to drainage issues
• May present with unusual pump noises (buzzing/grinding) or leaks at the pump housing
• Restores proper water evacuation to allow cycles to finish

• Unplug the appliance and turn off water supply before servicing
• Expect residual water—use towels or a shallow pan when removing hoses
• Access the pump (front lower or rear panel varies by model); disconnect wiring and hoses, and transfer any brackets/grommets from the old pump if needed
• Clear the drain filter, sump, and hose of debris; then test for leaks after installation

The Washer Filter Assembly is an essential component for maintaining your Samsung washer's optimal performance. This genuine OEM part ensures a perfect fit and reliable functionality, specifically designed for Samsung washing machines. By effectively trapping lint, debris, and other particles, the filter assembly helps prevent blockages and enhances the efficiency of your washer. Installing this filter assembly is straightforward, allowing you to quickly restore your appliance's performance without hassle. Regular replacement with this genuine OEM part can extend the lifespan of your washer, reducing the need for costly repairs. Additionally, maintaining a clean filter assembly contributes to cleaner laundry results, providing a better washing experience. Compatible with a wide range of Samsung washer models, this washer filter assembly offers both quality and peace of mind. Choose the Washer Filter Assembly to ensure your Samsung washer operates smoothly and efficiently for years to come.

This is the water pump that moves water through your appliance so cycles can run correctly. Replacing a failing pump restores proper water flow and helps prevent standing water, poor performance, and leaks. What it does:

• Circulates and/or removes water as the appliance operates
• Supports proper flow so wash/rinse/drain steps can complete
• Maintains a sealed path at the pump connections to help prevent leaks
• Typical symptoms of a failing pump: standing water, weak/no water movement, loud humming or grinding from the pump area, leaks, or related drain/circulation errors

• 1 water pump

• Disconnect power and shut off water supply before servicing
• Have towels/containment ready; some residual water is normal when hoses are removed
• Move wires and hoses one-for-one to the new pump; tighten clamps and check any O-rings/seals
• Run a short test cycle and inspect for leaks and proper water movement

2 Port. Whirlpool and Kenmore washers.

The Washer Drain Pump Assembly ensures your Samsung washer efficiently removes water after each cycle. This genuine OEM part is specifically designed to fit a variety of Samsung washer models, guaranteeing a secure and reliable connection. Built with durability in mind, the drain pump assembly effectively prevents leaks and maintains optimal washing machine performance. By replacing a faulty or worn-out pump with this high-quality assembly, you can restore your washer's functionality and extend its lifespan. Installation is straightforward, allowing you to quickly get your appliance back in working order without hassle. The Washer Drain Pump Assembly not only enhances the efficiency of your washer but also contributes to a smoother and more dependable laundry experience. Trust in this genuine OEM part to provide the performance and reliability you expect from your Samsung appliance, ensuring your washer operates seamlessly for years to come.