Kitchenaid Dishwasher Parts

Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure. Read more

Replace the leaking seal. Part fitment was original and easy to replace. Read more

The upper spray arm mount on our KitchenAide dishwasher wore out, allowing the spray arm to droop into the dishes and pots in the lower rack. The replacement part was in stock and it arrived the very next day after I ordered it, with no special shipping cost. An amazing experience! The part took just 10 minutes to install--it could have taken less, but it always takes a few more minutes with a new fix. The washer is back in action, as good as new. I'm delighted with the response of... Read more

• Door latch failure

Had to remove the screws that hold the dish washer to the counter top by knocking them out of the counter top. After seeing how the door handle worked I will not have to do again as all you have to do to open is stick a long screw driver up inside and push the chip and it opens. Ordered handle installed it now everything works fine. $29.00 for little plastic handle seems quiet rediculous but Kitchenaid and parts direct where $39.00 so I guess I got a bargain. As for the tools you a trox driver... Read more

I figured out that it was probably a plugged pump hose, since the pump would run, it somtimes it drained and sometimes it didn't. Your video helped with how to take the dishwasher out and replace the hose. I replaced the hose and everything is now working fine. It turned out to be a broken check valve in the old hose that caused the problem. It took 90 mins to do the repair. Read more

Removed the old planetary and cleaned metal shavings from gears. Transferred the old axle/gear assembly onto the new planetary. Inserted the new (and expensive) screw for the main gear and torqued it very tight (as well as the original other four screws). Slid the new planetary gears together and re-inserted the holding pin. Tapped on the cover ring and was done. Read more

Looked at Utube video. Was not as easy as it seemed to be. But I got it Read more

Somehow my Whirlpool dishwasher spray arm and supply tube broke. The plastic literally snapped. I tried to glue it back with Gorilla glue but it didn't hold due to the high heat... so in a few weeks I had the same problem again. I ordered both the Spray Arm and Supply Tube Kit and the Upper Spray Arm Mount Assembly. BTW I also ordered the Wash Arm Tube Holder not knowing that one came with the Spray Arm and Supply Tube Kit (NO BIG DEAL). The on-line videos with your website made the repair work... Read more

Watched your very helpful and informative "how to" video and replaced both right and left hinges. Getting the front panel to line up on the clips was the most difficult part. Read more

I searched the model on Appliancepartspros.com and ordered the items needed with overnight shipping. My order came the next day :) All parts were in stock and came clearly labeled and orderly packaged. Within 10 minutes my dishwasher was back in business and I was one happy camper. I would order from here again anytime and attempt to fixt the issue myself. Much cheaper that having somebody come out, only to tell you that they have to order the parts and come back at a later time to fix the... Read more

Replaced the main pump and motor assembly. Read more

Ordered new control panel...got it in two business days-fixed the problem-5 minutes to replace Read more

All of the repairs were incredibly easy, however the experience might be different for everyone. My skills and background experience make troubleshooting and repairing fairly easy for me. I began the journey by troubleshooting out some of the peripherals such as the float mechanism and door latch switch by using a multimeter to ohm them out. I then moved towards the thermostat and turbinator. I measured the resistance on the thermostat and it seemed to be fine. I then cleaned the turbinator... Read more

Fixed with your replacement Read more

Part was updated from original equipment (3 pieces) to a one piece tube. Snip the top of hanger loop then install. Just a couple minute job. Updated tube is much better than the original design. Read more