Skip to Content
  • 2 Day Quick Delivery! 2 Day Quick Delivery!
  • 365 Day Return Policy! 365 Day Return Policy!
  • 15 million satisfied customers 15 million satisfied customers
  • Over 2.1 Million Parts In Stock Over 2.1 Million Parts In Stock
  • Repair ForumFree Tech Support!
  • Google Trusted Store Google Trusted Store

Kitchenaid Dishwasher Parts

Best Seller
Kitchenaid Hose-Drain
Genuine Whirlpool part
By: Whirlpool
Part Number: W11381654

The Drain Hose is an OEM part for Whirlpool dishwashers. It serves as the connection that allows dirty water to exit the dishwasher tub and flow into the water drain system after each wash cycle. The hose transports wastewater from inside the dishwasher out through the standpipe.

Causes of a bad drain hose can include mineral or food debris buildup blocking water flow within the hose, cracks or breaks in the plastic material from repeated bending, or a loose or damaged hose clamp connection.

Symptoms of a drain hose failure include:

  • Standing water remaining in the bottom of the tub after a cycle
  • Puddles or leaks developing near or underneath the dishwasher
  • Water failing to properly drain during the designated drain portion of cycles
  • Kinks or sagging appearing in the hose affecting water drainage

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

More
$28.43
Compare At:
$34.12
You Save:
$5.69

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Pump Outlet Seal
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302711

Seals the discharge connection on your dishwasher pump to prevent leaks during wash cycles. Replace if water pools under the unit. Verify fit by model.

Do-It-Yourself Stories from Customers like You Loud dishwasher producing dirty dishes   Leon F. • Sylmar , CA • November 11, 2015

I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again. Read more

More
$25.76
Compare At:
$30.40
You Save:
$4.64

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Dishrack Wheel
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3385088

Replacement dishwasher dishrack wheel installs on the upper or lower rack to restore smooth gliding. Replace worn, broken, or missing wheels to fix jamming.

Do-It-Yourself Stories from Customers like You Upper tray roller failure   Michael S. • Atascadero , CA • February 28, 2022

Ordered replacement parts and installed them. A lot less expensive than having a dealership fix it. Read more

More
$12.95
Compare At:
$15.54
You Save:
$2.59

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Power Cord Kit
Genuine Whirlpool part
By: Whirlpool
Part Number: 4317824

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

  • The dishwasher not turning on or completing cycles
  • Warm or hot power cords during operation
  • Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

Do-It-Yourself Stories from Customers like You Mice chewed the drain hose and power cord   Noah C. • Eastsound , WA • February 16, 2015

Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly. Read more

More
$22.53
Compare At:
$26.81
You Save:
$4.28

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Track
Genuine Whirlpool part
By: Whirlpool
Part Number: W10914507

The Dishrack Track (Right) is an OEM part for Whirlpool dishwashers. It is responsible for supporting the third-level dishrack and allowing it to glide in and out smoothly during the loading and unloading process. This track is designed specifically for the right side of the third-level rack. 

Causes of a bad track include damage from heavy use over time, such as dulling or bending of the metal track surface from repeated loading/unloading of dishes. Debris or residue buildup along the track can also cause issues.

Symptoms of a bad track include:  

  • Rack that will not fully extend or retract
  • Binding or sticking during rack movement  
  • Rack that will not stay positioned above

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

More
$78.78
Compare At:
$93.75
You Save:
$14.97

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Circulation Pump Rotor
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8194092

Fix a dishwasher that won't spray water with a new circulation pump rotor. Couples with stator to drive wash impeller. DIY repair takes about 2 hours.

This part fixes the following symptoms
  • Noisy
  • Won't start
See more...
Do-It-Yourself Stories from Customers like You Replaced pump rotor and pc board   Dale C. • Brockport , NY • March 15, 2015

The PC board was bigger than the original so had to modify the mounts, the pump and rotor are pretty straight forward but would have much easier with another pair of hands. It took about 2 hours start to finish. One and a half days to get the parts, fantastic service. A new dishwasher is $1300.00. the parts were $314.00, so more than worth fixing. Read more

More
$206.95
Compare At:
$244.20
You Save:
$37.25

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Electronic Control Board
Genuine Whirlpool part
By: Whirlpool
Part Number: W10854216

Fix dishwashers that won't start, stop mid-cycle, or display error codes with this electronic control board. Moderately challenging DIY repair.

More
$151.51
Compare At:
$178.78
You Save:
$27.27

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Control Board
Genuine Whirlpool part
By: Whirlpool
Part Number: W11368631

Fix a dishwasher that won't start or has no power with a new control board. This part coordinates all cycle functions and monitors safety features.

Do-It-Yourself Stories from Customers like You Shuts down mid cycle   Robert L. • Jeffersonville , IN • May 17, 2026

Display would flicker "Delay" light and then shut down. Replaced control board and door switch. Read more

More
$133.37
Compare At:
$158.71
You Save:
$25.34

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher User Interface Control Board
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8270168

Fix unresponsive buttons, cycles that won't start, or blinking lights. This user interface board restores control panel function in about 30 minutes.

Do-It-Yourself Stories from Customers like You The start button would not work   Ruth M. • Brooklyn , NY • May 10, 2016

1. Turn off the electricity to the dishwasher 2. Unscrew all of the screws on the inside of the dishwasher door. 3. Take off the door and put it aside 4. Loosen the panel that contains the control board, control panel and the door lock mechanism 5. Using a screw driver, push in the small moveable tab in the center of the plastic clip that is holding the control board to the plastic panel. 6. Unhook the ribbon that is attached to the bad control board. 7. Attach the ribbon to the new control... Read more

More
$212.11
Compare At:
$233.32
You Save:
$21.21

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Stand Mixer Phase Control Board
Genuine Whirlpool part
By: Whirlpool
Part Number: W11174552

This is the electronic phase control board that regulates the motor speed in a stand mixer. It adjusts power delivery to the motor based on the speed setting selected by the user. Replace this board if the mixer runs at only one speed, does not respond to speed adjustments, intermittently stops during operation, or fails to turn on entirely.

Do-It-Yourself Stories from Customers like You Would not turn on   Pat T. • Coeur D'alene , ID • December 13, 2015

I replaced the Board-Phas and speed control plate since power was not making it to the motor. When I received the speed control plate it had nuts on the upper screws with springs, since my old one didn't have nuts I assumed that the nuts were to keep the springs on until installed. After putting it back together, I noticed that though it worked, the first two settings did nothing. Now, guys, I was desperate, OK. I downloaded the service manual and read it from front to back, and when I got to... Read more

More
$21.95
Compare At:
$26.12
You Save:
$4.17

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Stand Mixer Power Cord
Genuine Whirlpool part
By: Whirlpool
Part Number: W11728151

Replacement power cord for stand mixers. Connects your mixer to the wall outlet. Replace if cord is frayed, damaged, or has exposed wiring.

Do-It-Yourself Stories from Customers like You Switch was stuck and didn’t work   Paul G. • New Haven , IN • July 08, 2025

Replaced control assembly, didn’t need to change power cord. The video made it easy. Read more

More
$27.37
Compare At:
$32.57
You Save:
$5.20

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Tine Row Holder
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8539102

Secures tines in your dishwasher rack to hold dishes and utensils in place. Replace if cracked, broken, or missing to restore proper rack function.

Do-It-Yourself Stories from Customers like You Broken plastic parts   Debbie K. • Manson , WA • March 04, 2017

Ordered and installed new parts. Amazingly fast service and user friendly website. Read more

More
$60.52
Compare At:
$72.62
You Save:
$12.10

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Circulation Pump And Motor Assembly
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10605058

Fixes dishwasher that fills but won't spray or clean dishes properly. Restores water circulation through spray arms. Average 3-hour DIY repair.

Do-It-Yourself Stories from Customers like You Whirlpool dishwasher about 2 years old would fill but would not wash it would empty when cancel was pushed   Joe G. • Middletown , CT • December 14, 2014

I paid $90 for a repairman fee to tell me I needed a motor. I submitted the same problem to you and you gave me the same advice for FREE. I ordered the unit from you . It came in promptly, It took me about 3 hours to replace and saved about a $300-$400.repair estimate. Thanks. Read more

More
$212.69
Compare At:
$253.10
You Save:
$40.41

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Planetary Drip Ring (Mixer)
Genuine Whirlpool part
By: Whirlpool
Part Number: WP240285

This planetary drip ring fits around a stand mixer's planetary assembly to cover the gap below the gearcase and help catch grease residue, restoring a clean, finished look where the beater hub meets the mixer head.

  • Mounts at the base of the mixer head around the planetary housing
  • Helps deflect incidental gearbox grease residue away from the bowl area
  • Covers the seam between housing and planetary for a clean, finished appearance
  • Replace if bent, cracked, loose, missing, or if you notice grease spotting beneath the planetary
What's included: One planetary drip ring. Install notes:
  • Unplug the mixer and remove the bowl and attachments
  • Gently pry off the old ring; clean the seating surface of debris or residue
  • Align and press the new ring evenly until fully seated; avoid deforming the ring or striking the gearcase
  • On some models, access may require lowering/removing the planetary
Note: This ring is a trim/deflector piece and not a fluid seal. Persistent oil leakage indicates separate gearcase service.

Do-It-Yourself Stories from Customers like You Worm gear failure on my KitchenAid 5 qt "professional" lift bowl mixer.   Edward B. • Mount Horeb , WI • January 24, 2020

This was a problem that I'd had previously with this mixer. The worm gear, which is designed to fail (so that more serious damage does not occur to the motor), did fail while I was mixing some multi-grain bread dough. After the previous failure (pre-youtube days), I took the machine in for repair. The repair-shop cost came to about $150 in labor. Parts were extra. This time, I decided to do the repair myself, since I figured that I knew what was wrong. I found the appliancepartspros... Read more

More
$13.95
Compare At:
$16.60
You Save:
$2.65

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Dishwasher Dishrack Tine Clip
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10077844

Secures tines in your dishwasher rack to keep dishes properly aligned. Replace this clip if it's cracked, broken, or missing to restore rack stability.

Do-It-Yourself Stories from Customers like You Top rack tracks and stoppers were broken   Martina B. • Helotes , TX • December 19, 2015

I searched the model on Appliancepartspros.com and ordered the items needed with overnight shipping. My order came the next day :) All parts were in stock and came clearly labeled and orderly packaged. Within 10 minutes my dishwasher was back in business and I was one happy camper. I would order from here again anytime and attempt to fixt the issue myself. Much cheaper that having somebody come out, only to tell you that they have to order the parts and come back at a later time to fix the... Read more

More
$11.78
Compare At:
$13.90
You Save:
$2.12

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Kitchenaid Washer Water Inlet Valve Screen
Genuine Whirlpool part
By: Whirlpool
Part Number: WP96160

This is a small mesh filter screen that fits inside the water inlet valve to catch sediment and debris from your household water supply before it enters the washer. It prevents mineral buildup and particles from clogging or damaging the valve internals. Replace this screen if your washer is filling slowly, not filling at all, or if the screen is visibly clogged, torn, or deteriorated.

Do-It-Yourself Stories from Customers like You Washing machine was having trouble delivering enough water on rinse cycle   Cynthia S. • Libertyville , IL • August 15, 2014

Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you! Read more

More
$11.78
Compare At:
$14.02
You Save:
$2.24

IN STOCK
Ships Monday Guaranteed
Add to Cart
  • Over 2.1 Million Parts In Stock Over 2.1 Million Parts In Stock
  • 2 Day Quick Delivery! 2 Day Quick Delivery!
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Google Trusted Store Google Trusted Store
​